Page is loading ...
1. To aim fixture, loosen both #10-32 x5/8" end screws. When
both indicators are lined up, the slope of the lens face is 40-
degrees. Each subsequent notch is an additional +/- 10-
degrees
2. When fixture head is rotated to desired angle, retighten end
screws to secure the position.
#10-32 x5/8"
End screw
Fixture head
indicator
Yoke arm
indicator
Warning
: Before starting any work ensure
that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician.
Do not
mount fixtures vertically.
Installation Instructions
Vault
C-Scroll
Roundel
These installation instructions are valid with the above Ametrix styles.
1
3
2
Sheet 1 of 2
Small, INDOOR
CR
(C
antilever
, R
emote ballast
)
Visor and Non-Visor
ADY071478 REV B (ECN80481)
Exploded View and part call-out
#8-32 x3/8"
Set screw
(2x)
Mounting
plate
Wiring the fixture
#10-32 x5/8"
End screw
(2x)
Fixture head
Attention:
All cantilever fixture assemblies require additional
bracing/structure around J-box to support fixture.
J-box
(by others)
Fasteners
(by others)
(4x)
#8-32 x3/8"
Set screw
(2x)
Securing the fixture to structure
1.
Secure fixture head to pendant yoke using both #10-32 x5/8"
end screws.
2.
Feed fixture wire through pendant tube.
3.
Remove both #8-32 x3/8" set screws and slide canopy down
pendant.
4.
Run wires from pendant and j-box through wiring holes in
mounting plate.
5.
Use appropriate fasteners, secure mounting plate to structure
around J-box.
Use additional bracing around J-box to
support fixture.
Aiming the fixture
Use additional bracing around
J-box to support fixture
Fixture
wire
Wiring holes
1.
After securing fixture to structure, attach appropriate wires
and ensure connections are properly matched.
2.
Push wire connections into J-box and cover mounting plate
with canopy.
3.
Secure canopy with both #8-32-3/8" set screws.
#8-32-3/8"
Set screws
(2x)
Use only GE and Sylvania
CFL lamps
Installation Instructions
Vault w/ visor
C-Scroll w/ visor
Roundel w/ visor
These installation instructions are valid with the above Ametrix styles
Mounting Plate Dimensions In [mm]
Lamping Size Chart
(lamps provided by others)
Warning
: Before starting any work ensure
that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician.
Do not
mount fixtures vertically.
Small, INDOOR
CR
(C
antilever,
R
emote ballast
)
Visor and Non-Visor
Sheet 2 of 2
ADY071478 REV B (ECN80481)
Side View Top View
5"
127
5"
127
4"
101.60
4"
101.60
1"
25.40
1"
25.40
1
4
" (4x)
6.35
1
2
"
12.70
1
2
"
12.70
7
16
"
11.42
on order
Length dependant
FIXTURE SIZE
(inches/ mm)
WATTAGE
# OF
LAMPS
LAMP TYPE LAMP DESCRIPTION
10
3/4
/ 273.05 39 W 1 T6 Ceramic Metal Halide
12
3/4
/ 323.85 70 W 1 T6 Ceramic Metal Halide
12
3/4
/ 323.85 150 W 1 T6 Ceramic Metal Halide
12
3/4
/ 323.85 26 W 1
4-Pin Triple
Tube
Compact Fluorescent
12
3/4
/ 323.85 32 W 1
4-Pin Triple
Tube
Compact Fluorescent
12
3/4
/ 323.85 42 W 1
4-Pin Triple
Tube
Compact Fluorescent
10
3/4
/ 273.05 100 W 1 T4 Halogen (Single Ended)
12
3/4
/ 323.85 150 W 1 T4 Halogen (Single Ended)
12
3/4
/ 323.85 250 W 1 T4 Halogen (Single Ended)
LAMP
(not to scale)
/
