2.
Visor and Non-Visor
Do not
performed by a certified electrician.
work must meet local/national codes and be
Warning
: Before starting any work ensure
that all sources of power are turned off. All
mount fixtures vertically.
Installation Instructions
1.
Sheet 1 of 3
Roundel, XL
IN/OUTDOOR
P1R
(Pendant, 1-way, Remote)
ADY080866 REV A(ECN080377)
Hex end bolt
All extra large fixtures require additional bracing/structure around J-box to support fixture.
End cap
3/8-16x1"
(by others)
Mounting plate
J-box
Canopy
dependant on order
Pendant length
plate
1-way Yoke
Yoke arms
Fixture door
Electrical cover
Exploded View and Part Call-Out
(x2)
Securing Pendant to Structure in Ceiling
(x2)
Hex bolt
Securing Yoke to Pendant
Attention:
spacer
Aiming screw
1/4-20 x 4"
1/4-20 x1"
Aiming screw
(x2)
1/4-20 x1"
Button socket screws
(x4)
yoke.
and secure using both 1/4-20 x 4" hex bolts.
After securing arms, slide 1-way yoke assembly onto pendant
2.
Yoke arms
Using all four 1/4-20 x1" screws, secure yoke arms to 1-way
yoke
1-way
1.
1/4-20 x 4"
Hex bolt
(x2)
Pan head screws
#10-32 x 1/2"
(x2)
(by others)
J-box
plate
Mounting
(by others)
Canopy
Appropriate fasteners
1.
Loosen both #10-32 x1/2" Pan head screws and allow canopy
to slide down pendant.
2.
Feed power wire from j-box into pendant, ensure wire reaches
electrical cover plate on base of pendant.
3.
Using appropriate fasteners(by others), secure mounting plate
to structure/bracing around J-box.
Securing and Wiring the Fixture Head to Pendant
Captive door
screws
(x10)
End cap
(x2)
1/4-20 x1"
Aiming screw
(x2)
Electrical cover plate
gasket
Wire connectors
(x2)
1.
To aim fixture, unscrew end caps from fixture. Loosen both 1/4-20 x1" aiming screws on both sides of fixture. When
yoke indicator and fixture head indicator are lines up the slope of the fixture head is 40-degrees. Each subsequent notch
is an additional 10-degrees. When fixture is rotated to desired angle, secure with aiming screws.
2.
Secure door using proper torque specifications and sequence as described in supplementary sheet.
3.
Thoroughly check seal on all gaskets and wire connectors to ensure seals are smooth and compressed.
End cap
Electrical cover
plate
3/8-16 x 1"
Hex end bolt
(x2)
1/4-20 x 1"
Aiming screw
(x2)
Wire connector
1.
While firmly supporting fixture head, use 3/8-16 x1" hex end bolt to secure fixture head to yoke arms.
2.
Slide one aiming screw spacer between fixture head and yoke arm on each side and secure fixture heads angle using 1/4-20 x1"
aiming screws.
3.
Remove electrical cover plate from pendant tube.
4.
Insert fixture head wire into wire connection at base of pendant tube and run up to electrical cover plate.
5.
Attach appropriate wires ensuring all connections are properly matched and replace electrical cover plate.
Aiming and Sealing Fixture
Aiming screw
spacer
(x2)
Side View
Warning
: Before starting any work ensure
that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician.
Do not
mount fixtures vertically.
Installation Instructions
4.
Sheet 1 of 3
Roundel, XL
IN/OUTDOOR
P1R
(Pendant, 1-way, Remote)
Visor and Non-Visor
3.
ADY080866 REV A(ECN080377)
40
Warning
: Before starting any work ensure
that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician.
Do not
mount fixtures vertically.
Installation Instructions
Sheet 3 of 3
Roundel, XL
IN/OUTDOOR
P1R (Pendant, 1-way, Remote)
Visor and Non-Visor
ADY080866 REV A(ECN080377)
16
"
6"
"
4
3
"
1"
4
R
3
R
3
6"
Front View Top View
1
2
"
dependant on order
Pendant length
Lamp Description
(lamps provided by others)
Mounting Plate Dimensions
In[mm]
FIXTURE SIZE
(inches/ mm)
WATTAGE
# OF
LAMPS
LAMP TYPE LAMP DESCRIPTION
LAMP
(not to scale)
27/ 685.8 250W 1 ED28 Metal Halide
27/ 685.8 400W 1 ED28/BT37 Metal Halide
27/ 685.8 400W 2 ED28/BT37 Metal Halide
27/ 685.8 750W 1 BT37 Metal Halide
27/ 685.8 1000W 1 BT37 Metal Halide
/
