Cooper Lighting AMETRIX ADY080863 User manual

Cooper Lighting
Brand
Cooper Lighting
Model
AMETRIX ADY080863
Type
User manual

This manual is also suitable for

access to bolts from side of fixture.
2.
Using 1/4-20 x1" screws, secure mounting brackets to bottom
Brackets can be attached as shown or reversed allowing
of ballast enclosure.
1.
Insert driver through
mounting holes in bracket
to secure brackets to ballast
enclosure.
Visor and Non-Visor
Sheet 1 of 3
performed by a certified electrician.
2.
Warning
: Before starting any work ensure
that all sources of power are turned off. All
work must meet local/national codes and be
mount fixtures vertically.
Installation Instructions
1.
Do not
Roundel, XL
IN/OUTDOOR
BI
(Base, Integral)
ADY080863 REV A(ECN080377)
Pre-installed
(x4)
1/4-20 bolts
1/4-20 nut
(x4)
1.
After securing mounting brackets to ballast enclosure, slide
brackets over pre-installed 1/4-20 bolts in mounting
surface.(Refer to page 3 for mounting dimensions)
2.
Using appropriate nuts, secure ballast enclosure to surface.
(x10)
1/4-20 x1"
Fixture door
screws
Exploded View and Part Call-Out
enclosure
Captive door
Aiming screw
(4x)
Securing Mounting Brackets
(2x)
(x12)
Integral ballast
Screw
cover plate
#10-32 x 1/2"
brackets (2x)
End cap
Pan head screws
Hex End bolt
Mounting
Ballast enclosure
(2x)
3/8-16 x1"
1/4-20 x1"
1/4-20 x1"
Screw
(4x)
Securing Ballast Enclosure to Surface
Aiming the Fixture
1. To aim fixture, unscrew end caps from fixture. Loosen both
1/4-20 x1" aiming screws on both sides of fixture. When yoke
indicator and fixture head indicator are lined up, the slope of
the lens face is 40-degrees. Each subsequent notch is an
additional 10-degrees.
2. When fixture is rotated to desired angle, re-tighten set screws
and replace end caps.
End cap
(x2)
Fixture head
indicator
Yoke arm
indicator
Wiring the Fixture
Ballast
cover plate
#10-32 x1/2"
Pan head screws
(x12)
1.
Loosen all 12 screws and remove ballast box cover plate.
2.
Attach appropriate wires ensuring all connections are properly
matched.
3.
Secure ballast box cover plate using all twelve screws.
Securing Yoke Arms to Ballast Enclosure
1/4-20 x 1"
Pan head screws
(4x)
Yoke arms
(2x)
1.
Attach yoke arms to ballast enclosure using all four 1/4-20x
1" Pan head screws.
Warning
: Before starting any work ensure
that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician.
Do not
mount fixtures vertically.
Installation Instructions
3
5
4
Sheet 2 of 3
6
Roundel, XL
IN/OUTDOOR
BI
(Base, Integral)
Visor and Non-Visor
ADY080863 REV A(ECN080377)
3/8-16 x 1"
Hex end bolt
(x2)
1/4-20 x1"
Aiming screw
(x2)
End Cap
Fixture Wire
Securing Fixture Head
1.
While firmly supporting fixture head, secure to yoke arms using
both 3/8-16 x1" hex end bolts.
2.
Slide spacers between fixture head and yoke and secure
fixture head position using both 1/4-20 x1" aiming screws.
3.
Insert fixture wire into compression fitting in ballast enclosure.
4.
Replace end cap.
Aiming screw
spacer
(x2)
12
7
8
"
327.03
C
L
3
654.05
4
25 "
1
6
165.10
"
2
"
32
13
10.32
(4x)
704.85
"27
4
3
10
1
4
"
260.35
Warning
: Before starting any work ensure
that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician.
Do not
mount fixtures vertically.
Installation Instructions
Sheet 3 of 3
Roundel, XL
IN/OUTDOOR
BI
(Base, Integral)
Visor and Non-Visor
ADY080863 REV A(ECN080377)
Mounting Plate Dimensions
In[mm]
Lamping Size Chart
(lamps provided by others)
FIXTURE SIZE
(inches/ m m)
WATTAGE
# OF
LAMPS
LAMP TYPE LAMP DESCRIPTION
LAMP
(not to scale)
27/ 685.8 250W 1 ED28 Metal Halide
27/ 685.8 400W 1 ED28/BT37 Metal Halide
27/ 685.8 400W 2 ED28/BT37 Metal Halide
27/ 685.8 750W 1 BT37 Metal Halide
27/ 685.8 1000W 1 BT37 Metal Halide
  • Page 1 1
  • Page 2 2
  • Page 3 3

Cooper Lighting AMETRIX ADY080863 User manual

Cooper Lighting
Brand
Cooper Lighting
Model
AMETRIX ADY080863
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents