Minka Group P1649-895-L User manual

Minka Group
Brand
Minka Group
Model
P1649-895-L
Type
User manual

This manual is also suitable for

Fig.1
Set#: A-021-580121
Mounting plate
Green screw
Wood screw (4)
Drywall anchor (4)
Mounting screw(2)
K1
K2
L
A
B
C
D
EF
G
H
I
J
M
N
INSTALLATION INSTRUCTIONS FOR P1648-895-L P1649-695-L
For LED Island
READ AND SAVE THESE INSTRUCTIONS
WA R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R
A V E R T I S S E M E N T ! C O U P E R L E C O U R A N T A U N I V E A U D E S F U S I B L E S O U D O D I S J O N C T E U
ASSEMBLING THE FIXTURE (Fig.1)
1. Shut off power at the fuse box or circuit breaker box. If necessary,
remove the existing fixture and its mounting hardware.
2. Carefully remove the new fixture from the carton and check that all
parts are included as shown in the illustration.
3. Position the mounting plate (B) onto the ceiling and mark the location
of four drywall anchors (A). Pre-drill the holes for drywall anchors (A)
and insert four drywall anchors (A) into the ceiling.
4. Attach mounting plate (B) to the junction box (not included) with
mounting screws (D)(size:8-32*1/2”L). The side of the mounting
plate (B) marked “GND” must face out.
5. Place wood screws (C) through mounting plate (B) and into drywall
anchors (A).
6. This fixture includes two 6” and six 12” rods. Determine the desired
hanging height and connect rods (K1:W30-1-783 and K2:W30-H-
783). Feed the fixture wire carefully through each rod.
7. Secure swivel (J) to the last section of rod (K).
8. Slide faceplate (H) onto two swivels (J) and secure tightly with lock
washers (G) and hex nuts (F).
9. Use wire nuts to connect red output wire (marked output +) from
driver to two red LED wires (marked LED +) from led module.
Connect black output wire (marked output -) from driver to two black
LED wires (marked LED -) from led module.
10. The support cable is provided to support the weight of the fixture
while wiring. Align the fixture to mounting plate (B) and attach hook
(M) on the end of support cable
（
N
）
into a slot located on mounting
plate (B). Carefully allow the support cable (N) to support the weight
of the fixture while wiring.
CONNECTING THE WIRES (Fig.2)
11. Connect the electrical wires as shown in Fig.2, making sure that all
wire connectors are secured. If your junction box has a ground wire
(green or bare copper), connect fixture's ground wire to it.
Otherwise, connect the fixture's ground wire directly to the
mounting plate (B) using the green screw (E) provided.
COMPLETING THE INSTALLATION
12. Raise faceplate (H) to mounting plate (B) and secure with screws
(I).
Your installation is now complete. Return power to the junction box and
test the fixture. Fig.2
IMPORTANT: Fixture should be installed by a qualified electrician
to ensure proper wiring and installation.
Dimmable with ELV and/or LED compatible wall
dimmer switches
  • Page 1 1

Minka Group P1649-895-L User manual

Minka Group
Brand
Minka Group
Model
P1649-895-L
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents