Minka Group P1641-895-L User manual

Minka Group
Brand
Minka Group
Model
P1641-895-L
Type
User manual

Minka Group P1641-895-L is a dimmable LED pendant light fixture. It comes with three 12" and one 6" rods, allowing you to customize the hanging height to your preference. The fixture includes three 12" and one 6" rods, allowing you to customize the hanging height to your preference. It is easy to install and can be completed by a qualified electrician. The fixture is compatible with ELV and/or LED compatible wall dimmer switches, giving you control over the brightness of the light.

Minka Group P1641-895-L is a dimmable LED pendant light fixture. It comes with three 12" and one 6" rods, allowing you to customize the hanging height to your preference. The fixture includes three 12" and one 6" rods, allowing you to customize the hanging height to your preference. It is easy to install and can be completed by a qualified electrician. The fixture is compatible with ELV and/or LED compatible wall dimmer switches, giving you control over the brightness of the light.

Fig.1
A
C
E
B
D
F1
F2
G
Set#A-021-112
Mounting plate
Green screw
Mounting screw(2)
INSTALLATION INSTRUCTIONS FOR P1641-895-L
For LED Pendant
READ AND SAVE THESE INSTRUCTIONS
WA R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R
A V E R T I S S E M E N T ! C O U P E R L E C O U R A N T A U N I V E A U D E S F U S I B L E S O U D O D I S J O N C T E U
ASSEMBLING THE FIXTURE (Fig.1)
1. Shut off power at the fuse box or circuit breaker box. If necessary,
remove the existing fixture and its mounting hardware.
2. Carefully remove the new fixture from the carton and check that all parts
are included as shown in the illustration.
3. Attach mounting plate (A) to junction box (not included) using mounting
screws (C) (Size: 8-32*1/2’’L). The side of mounting plate (A) marked
“GND” must face out.
4. Fixture includes three 12" and one 6" rods. Determine desired hanging
height and thread rods (F1:W30-1-783 and F2:W30-H-783) to all thread
on top of fixture. Feed fixture wire carefully through each rod. If installing
with one 6" rod only. the all thread must be removed.
5. Secure rod to swivel of canopy (E).
6. Use wire nuts to connect red output wire (marked output +) from driver
to red LED wire (marked LED +) from led module. Connect black output
wire (marked output -) from driver to black LED wire (marked LED -) from
led module.
CONNECTING THE WIRES (Fig.2)
7. Connect the electrical wires as shown in Fig.2, making sure that all wire
connectors are secured. If your junction box has a ground wire (green
or bare copper), connect fixture's ground wire to it. Otherwise, connect
the fixture's ground wire directly to mounting plate (A) using the green
screw (B) provided.
COMPLETING THE INSTALLATION
8. Align canopy (E) onto mounting plate (A) and secure with screws (D).
Your installation is now complete. Return power to the junction box and test
the fixture.
Fig.2
IMPORTANT: Fixture should be installed by a qualified electrician
to ensure proper wiring and installation.
Dimmable with ELV and/or LED compatible wall
dimmer switches
  • Page 1 1

Minka Group P1641-895-L User manual

Minka Group
Brand
Minka Group
Model
P1641-895-L
Type
User manual

Minka Group P1641-895-L is a dimmable LED pendant light fixture. It comes with three 12" and one 6" rods, allowing you to customize the hanging height to your preference. The fixture includes three 12" and one 6" rods, allowing you to customize the hanging height to your preference. It is easy to install and can be completed by a qualified electrician. The fixture is compatible with ELV and/or LED compatible wall dimmer switches, giving you control over the brightness of the light.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents