Techni Mobili RTA-8401-OAK Owner's manual

Thanks for purchasing one of our products.

Please read carefully the assembly instructions before the installation.

Please save this manual for future reference.

ASSEMBLY INSTRUCTIONS

▪

A B

-Top Panel Lower  Lower

Stand Panel Lower

FG

Front Crossbar

Lower

H

Leg Crossbar

Right & Left x 2

C

Side Panel Left Lower

D

Side Panel Right Lower

I

Leg Crossbar

Back - Front Leg Left

- Front Leg Right - Back Leg Left - Back Leg Right

KL

J

E

Partition Panel Upper Side Panel Left

Upper

PQ

O

M N

Top Panel Upper Bottom Panel Upper

RS

Drawer Side

Panel Left - B x 2

Drawer Side

Panel Right - B x 2

S2 S3

S1 S4

T

Drawer Side

Panel Left - S x 5

Drawer Side

Panel Right - S x 5

T2 T3

T1 T4

U

-Drawer Bottom

Panel - S x 3

U2 V

U1

Side Panel Right

Upper

Stand Panel

Upper x 3 Drawer Front - B x 2

Drawer Front - M

x 2

Drawer Front-S x 3

S5



▪

PART QTY. ITEM

1 10Pcs Wooden Pin

6x25mm

38Sets

4

8Pcs Screw - 3.5 x 15mm

5Hole Covers

3

10Pcs

7

16Pcs Screw - 4 x 38mm

Cam Lock &

Bolt Sets

15mm

20Pcs Screw - 4 x 30mm

6

2Sets Drawer Metal

Sliders Set

8

4Pcs

9

10

7Sets

8Pcs Screw - 5 x 8mm

11

270Pcs Wooden Pin

8x25mm

10Sets

Cam Lock &

Bolt Sets

12mm

Attention : Holes on panels may be hidden underneath PVC laminate!!!

Do not tighten the screws until all of them are in the right position.

Plastic Feet

Handle ( 2293 )

M4x20mm

Handle Screw

12

1

- Install all the thick wooden pins (2) into the panels shown in the illustrations, but please make sure

to insert them in the correct holes as some holes are intended for cam bolts in subsequent steps.

2

T1

T1 T1

T1 T2

T2

1

2x70

B

CD

EF

G

H

NO

P

Q

RRR

S1

S2

2

- Install all the thin wooden pins (1) into the panels shown in the illustrations, but please make sure

to insert them in the correct holes as some holes are intended for cam bolts in subsequent steps.

1x10

3

▪ Attach Bolts (4) to all panels as shown, but please make sure to insert them in the

correct holes as some holes are intended for the wooden pins in subsequent steps.

4

- Attach Bolts (3) to all panels as shown, but please make sure to insert them in the correct

holes as some holes are intended for the wooden pins in subsequent steps.

3

4x38

KLIJ

S

PQ

MO

CD

B

A

4

3x10

UUU

TT

5

▪ Assemble the FLAT shaped drawer sliders (9) to the panels (C), (D) and (E) using screws

(12) as shown. In panel (E), the sliders attach on both sides of the panel. Set aside the "L"

shaped drawer sliders as they will be used until step 19.

6

▪ secure with (4)

12

9

E

CD

RIGHT VIEW

LEFT VIEW

BE

9

x8 x2 Sets

12

x1

4

7

▪ secure with (8)

8

▪ Position all the panels as shown in both illustrations, paying close attention

to the orientation of legs (K) and (L), and then assemble the panels using

Cam Locks (4) as shown.

8

F

CK

I

G

DJ

G

L

x1

8

4

x8

4

9

▪ secure with

6 Pcs (4)

10

▪ secure with 8 Pcs (4) as shown.

10

H

B

FD

L

C

K

4

-Attach all Plastic Feet (10) to Leg (I), (J),(K) & (L) as shown.

I

J

A

4

x6

4x4

10

x8

4

11

▪ secure with (8)

12

▪ secure with (8)

13

▪ secure with (4)

8

R

O

R

N

8

4

x2

8

x1

4

x1

8





outwards, and its groove faces down)

14

▪ secure with 4 Pcs (4)

15

▪ Turn the assembled pieces over again, and assemble panel (M) secure

with 4 pcs of Cam Locks (4) as shown.

16

Turn the assembled pieces over, and insert back panel (V) with its finished

side facing outwards as shown.

4

P

V

M

Q

4

x4

4

x4

4



(The groove on "M" faces down).

17

19

-

bottom of the drawers using screws (6) as shown.

Please refer to the illustration for the correct

installation, because if they protrude at the



drawer won't fit in the unit.

-Assemble drawer back panel (S3),

secure with screw (8) as shown.

-Attach Hole Covers (5) to panels (S1) &

(S2) as shown.

18

20

S4

S2

S5

S1

8

S3

9

6

9

6

511

S

-Install Handle with screw (11) to panel (S)

as shown.

S

S2

S1

x3

4x5

8

Left

x4

6

x1 Set

9x2

5

x1

11

-Repeat steps 17 to 20 for the second

large drawer.

21

23

-Assemble drawer side panel (T1) & (T2) to

drawer front (T), secure with Cam Locks (3)

as shown.

-Assemble drawer back panel (T3),

secure with screw (7) as shown.

-Insert drawer bottom panel (T4) as shown.

22

24

T2

T1

T4

T

T3

7

11

T

-Repeat steps 21 to 24 for the second

medium drawer.

3

x4

7

x2

3

x1

11

-Install Handle with screw (11) to panel (T)

as shown.

25

27

-Assemble drawer side panel (T1) & (T2) to

drawer front (U), secure with Cam Locks (3)

as shown.

-Assemble drawer back panel (U1),

secure with screw (7) as shown.

-Insert drawer bottom panel (U2)

as shown.

-Repeat steps 25 to 28 for the other two

small drawers.

26

28

U2

T2

T1

U

U1

11

7

U

x2

3

x4

7

x1

11

29

- secure with (8)

30

-Place all Drawers into cabinet as shown.

5

8

-Attach 6 Pcs Hole Covers (5) to panels (G) & (H) as shown.

G

H

G

U

T

S

U

T

S

x6

5x2

8

Techni Mobili RTA-8401-OAK Owner's manual

Techni Mobili RTA-8401-OAK Owner's manual

Related papers

Other documents