RTA Techni Mobili RTA-S07 Assembly Instructions Manual

RTA
Brand
RTA
Model
Techni Mobili RTA-S07
Type
Assembly Instructions Manual
MODEL RTA-S07
MODEL RTA-S07
RTA-S07
DIMENSIONS
MAXIMUM WEIGHT CAPACITIES
DO NOT exceed this limit
Please use care and good judgement
when placing objects on wood surface
Product Size: 17"W x 16"D x 25"H
Small drawer inside space: 13.5"W x 13"D x 3"H
File drawer inside space: 13.5"W x 13"D x 10.4"H
RTA-S07
P.3
2
3
1
4
7
8
5
6
9
10 11 12
PARTS LIST
Right
Left
Right
Left
4
9
21
14
18
20
Small Drawer Left
Panel
Small Drawer Right
Panel
Caster
Top Drawer Front
Panel
Drawer Bottom Panel
Small Drawer Back
Panel
File Drawer Left
Panel
File Drawer Right
Panel
File Drawer Front
Panel
File Drawer Back
Panel
File Tube
Slider
x2 x2
x4
x3
x2
x2
x3 SETS
RTA-S07
P.4
18
17
19
20
1413 16
15
21
22
22A 22B
22C
22D
22E
22F
22G
SCREWS LIST
A
B
C
3X15 MM
6X40 MM
4X14 MM20
12
40
PART
QTY.
ITEM PART
QTY.
ITEM
D
6X12 MM
4X35 MM
6
1
1
E
18
F
1
4X20 MM
Handle
Left Panel
Right Panel
Bottom Panel
Back Panel
Top Panel
Bracket and nut, SET
File Drawer Caster
Middle Drawer Front
Panel
Locking Fittings
x3
Cam lock
Cam bolt
1. 2. 3.
Screw the bolt into the
corresponding panel.
In the other panel, insert
and align the cam lock.
Join the panels.
Turn the cam lock.
MISALIGNED:
TURN CAM LOCK
TO POINT TOWARDS
THE HOLE
CORRECT
HOW TO ASSEMBLE USING BOLTS AND CAM LOCKS:
If the panel already comes with the cam lock inserted, make sure is aligned:
RTA-S07
P.5
P.6
30mm
RTA-S07
P.7
RTA-S07
ASSEMBLY STEPS:
1
Tighten the metal plates
on the marked position
of the metal bar
22C
22C
22C
22C
22A
22A
22F
22F
22E
22C
22C
22F
Insert the metal fittings into the bar (22E) in the following order: (22A)x1, (22C)x3, (22A)x1. Then tighten
the (22C) on the marked positions of the bar (22E).
15
22A
SCREWS
C
8PCS
3X15 MM
2
X2
Place the bar (22E) inside the channel of Right panel (15) with the tubes
towards the top of the panel, and secure the fittings (22A) to the panel using
Screws (C).
P.8
RTA-S07
14
15
15
14
16
12
Right
Left
12
X3
X3
SCREWS
C
12PCS
3X15 MM
SCREWS
4PCS
6X40 MM
A
14
15
17
3
4
5
Screw the Bolts (A) to the corresponding holes on the inside
face of Left & Right Panels (14&15), then assemble the
panels to the Bottom Panel (16) by turning all the
corresponding cam locks.
Grab all the flat shaped sliders (12) and set aside the “L” shaped ones. Assemble the sliders to the inside
face of the Left & Right Panels (14&15) with using Screws (C). The wheels will be located at the front and
facing down.
If you don't see the holes, pass the tip of your finger around the area where
the holes should be, pressing against the surface to feel the indentation.
Slide the Back Panel (17) thru the channels in
between panels (14), (15) & (16) as shown.
Make sure the panel fits inside all the
channels.
16
P.9
RTA-S07
14
15
18
16
2
8
SCREWS
4PCS
6X40 MM
A
3
3
SCREWS
16PCS
4X14 MM
E
SCREWS
C
6PCS
3X15 MM
6
7
8
22B
22B
22B
2
Screw the Bolts (A) to the bottom face of the Top
Panel (18), then assemble it to the cabinet by turning
the corresponding cam locks.
Use Screws (E) to assemble the Casters (3) to the
Bottom Panel (16).
Use Screws (C) to attach the lock fittings (22B) to the outside face of the
Small Drawer Right Panels (2) and File Drawer Right Panel (8).
P.10
RTA-S07
Screw Bolts (A) to the holes on the inside face of Top Drawer Front Panel (4)
and Middle Drawer Front Panel (21). Then assemble the Small Drawer Left &
Right Panels (1&2) to Top Drawer Front Panel (4) and Middle Drawer Front
Panel (21) as shown by turning the cam locks.
SCREWS
8PCS
6X40 MM
A
9
1
2
4
1
2
21
10
5
1
2
1
2
5
Slide the Drawer Bottom Panels (5) thru the channels in between panels (1), (2) and (4) / (21) as shown.
Make sure the panel fits inside all the channels.
SCREWS
8PCS
4X35 MM
B
11
6
2
1
1
2
6
Assemble the Small Drawer Back Panels (6) in between the Small Drawer
Left & Right Panels (1&2) using Screws (B) as shown.
P.11
RTA-S07
1
1
Left
12
Left
12
12
Right
12
Right
SCREWS
C
8PCS
3X15 MM
Left
12
12
Right
SCREWS
C
2PCS
3X15 MM
12
13
4
22G
22D
Place the small drawers upside-down. Grab the “L” shaped sliders (12) and
assemble them to the drawers using Screws (C), with the wheels facing
towards the back of the drawers. Make sure the sliders are touching the side
panels, and that they are not “up in the air”.
Assemble the lock (22D) and ring (22G) to the Top Drawer Front Panel (4)
using Screws (C).
IMPORTANT: The rod on the lock MUST face down, and the lock MUST turn
counter-clockwise with the key.
SCREWS
4X20 MM
D
4PCS
14
4
21
13
13
Assemble the Handles (13) to the small drawers using Screws (D) as shown.
P.12
RTA-S07
20
19
SCREWS
2PCS
4X14 MM
E
9
19
1PC
6X12 MM
F
E
E
F
9
7
8
SCREWS
4PCS
6X40 MM
A
15
16
17
Assemble the Bracket (19) to the bottom of the inside face of the File
Drawer Front Panel (9) using Screws (E) & (F) as shown.
Attach the File Drawer Caster (20) to the Bracket (19) using the nut and tighten with the wrench.
Screw the Bolts (A) to the inside face of the File Drawer Front Panel (9) as
shown. Then assemble the File Drawer Left & Right Panels (7&8) by turning
the cam locks.
P.13
RTA-S07
7
8
18
5
Slide the Drawer Bottom Panel (5) thru the channels in between
panels (7), (8) and (9) as shown. Make sure the panel fits inside
all the channels.
7
8
10
9
11
10
SCREWS
4PCS
4X35 MM
B
19
20
Assemble the File Drawer Back Panel (10) to the File Drawer Left
& Right Panels (7&8) using Screws (B) as shown.
Carefully insert the File Tubes (11) thru the File Drawer Back Panel (10)
and screw them into the insert of the File Drawer Front Panel (9).
WARNING: DO NOT OVERTIGHTEN the tubes as it may perforate and
damage the front panel. Such damage is not covered by the product's
warranty.
P.14
RTA-S07
7
12
Right
Left
12
9
SCREWS
C
4PCS
3X15 MM
Left
12
12
Right
SCREWS
4X20 MM
D
2PCS
13
4
9
21
21
22
23
Place the file drawer upside-down. Grab the “L” shaped sliders (12)
and assemble them to the file drawer using Screws (C), with the
wheels facing towards the back of the drawer. Make sure the sliders
are touching the side panels, and that they are not “up in the air”.
Attach the Handle (13) to the file drawer using Screws (D) as shown.
Carefully insert all the drawers starting from the bottom.
Make sure the wheel from the drawers engage and roll in
the middle of the sliders.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

RTA Techni Mobili RTA-S07 Assembly Instructions Manual

RTA
Brand
RTA
Model
Techni Mobili RTA-S07
Type
Assembly Instructions Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents