ML Accessories HCBC User manual

Brand: ML Accessories

Model: HCBC

Type: User manual

ML Accessories HCBC is a low voltage recessed ceiling light that can be used for general indoor lighting purposes. It is dimmable, allowing you to adjust the brightness to your preference. The HCBC has an IP20 rating, indicating that it is suitable for indoor use only and should not be exposed to moisture or water. It has a 1-year warranty from the date of purchase and should be installed by a qualified electrician in accordance with the latest edition of the IEE Wiring Regulations (BS7671).

INSTALLATION & MAINTENANCE MANUAL

HCxx

HCXX INSTRUCTIONS.indd 1HCXX INSTRUCTIONS.indd 1 02/05/2023 16:41:0902/05/2023 16:41:09

These instructions should be read carefully and retained after installation by the end user for future

reference and maintenance.

These instructions should be used to aid installation of the following products:

HCBC / HCC / HCW

GENERAL INSTRUCTIONS

• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)

and current Building Regulations. If in any doubt, consult a qualiﬁed electrician

• Please isolate mains prior to installation or maintenance

• Allow 50mm above and around the product for air dissipation (do not cover with insulation)

• This product is for indoor use only

• This product is either Class I and must be earthed or Class III depending on the choice of lampholder

• This product is IP20 rated

SAFETY

• The following instructions assume an existing cut-out of diameter from 78 to 120mm

• If cutting a hole, ensure not to infringe with any joists, gas/water pipes or electrical cables

• Choose which lampholder to use, either the 12V MR16 or the 230V GU10, and ﬁt this to the secondary

side of the terminal box, replacing the existing if necessary

• If using the 230V GU10 lampholder, connect the terminal box to the mains supply ensuring the correct

polarity is observed: L - Live (brown), E - Earth (green/yellow), N - Neutral (blue)

• If using the 12V MR16 lampholder, connect the terminal box to the secondary side of the 12V transformer

or driver (not included) in either polarity. The earth terminal must not be connected

• Separate the ﬁtting from the outer part of the hole converter by pulling downwards from the middle

INSTALLATION

HCXX INSTRUCTIONS.indd 2HCXX INSTRUCTIONS.indd 2 02/05/2023 16:41:0902/05/2023 16:41:09

• Offer the outer part of the hole converter to the ceiling and pass the terminal block and bracket through

• Hold the bracket with the “H” shaped hole over the same shaped hole in the side of the ﬁtting, with the

terminal box facing away from the centre of the ﬁtting

• Still holding the bracket in place, grip one of the retaining springs and squeeze the coils together with the

short leg facing downwards

• Hook the coils of the spring into the middle of the “H” shaped holes so that the ﬁtting and bracket are held

together (see Fig. 1)

INSTALLATION & MAINTENANCE MANUAL

These instructions should be read carefully and retained after installation by the end user for future reference

and maintenance.

These instructions should be used to aid installation of the following product(s):

HCBC / HCC / HCW

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

• Please isolate mains prior to installation or maintenance

• Allow 50mm above and around the product for air dissipation (do not cover with insulation)

• This product is for indoor use only

• This product is either Class I and must be earthed or Class III depending on the choice of lampholder

• This product is IP20 rated

INSTALLATION

• The following instructions assume an existing cut-out of diameter from 78 to 120mm

• If cutting a hole, ensure not to infringe with any joists, gas/water pipes or electrical cables

• Choose which lampholder to use, either the 12V MR16 or the 230V GU10, and fit this to the secondary

side of the terminal box, replacing the existing if necessary

• If using the 230V GU10 lampholder, connect the terminal box to the mains supply ensuring the correct

polarity is observed: L - Live (brown), E - Earth (green/yellow), N - Neutral (blue)

• If using the 12V MR16 lampholder, connect the terminal box to the secondary side of the 12V

transformer or driver (not included) in either polarity. The earth terminal must not be connected

• Separate the fitting from the outer part of the hole converter by pulling downwards from the middle

• Offer the outer part of the hole converter to the ceiling and pass the terminal block and bracket through

• Hold the bracket with the "H" shaped hole over the same shaped hole in the side of the fitting, with the

terminal box facing away from the centre of the fitting

• Still holding the bracket in place, grip one of the retaining springs and squeeze the coils together with

the short leg facing downwards

• Hook the coils of the spring into the middle of the "H" shaped holes so that the fitting and bracket are

held together (see Fig. 1)

Fig. 1

• Fix the other spring into the other side of the fitting in the same manner

• Holding the outer part of the hole converter in position, pass the terminal box through the centre, hold

the long legs of the springs upwards and pass them through the hole, keeping the short legs

downwards (see Fig. 2)

• Fix the other spring into the other side of the ﬁtting in the same manner

• Holding the outer part of the hole converter in position, pass the terminal box through the centre,

hold the long legs of the springs upwards and pass them through the hole, keeping the short legs

downwards (see Fig. 2)

Fig. 1

HCXX INSTRUCTIONS.indd 3HCXX INSTRUCTIONS.indd 3 02/05/2023 16:41:0902/05/2023 16:41:09

Fig. 2

• As the fitting is pressed into position in the centre of the plate, the long legs will engage with the top

surface of the ceiling, and the short legs will engage with the inner surface of the outer ring

• Remove the circlip fitted into the lamp aperture in the bottom of the fitting

• Fit a suitable lamp, max. 50W (not included)

• Insert the lamp into the centre of the fitting and replace the circlip

• Switch on and check for correct operation

GENERAL

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the

product.

This product is dimmable dependent on lamp type.

This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities

for where facilities exist.

WARRANTY

This product has a warranty of 1 year from date of purchase. Failure to install this product in accordance with

the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will

invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of

purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation

costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve

the right to alter product specification without prior notice.

ICONS: 230V 50Hz, 12V, IP20, Class 1, Class 3, Dim, Non-IC, indoor only

DCMAY21_V2

EU authorised representative: SLV Group Holdings GmbH, Niederkasseler Lohweg 18, Germany – 40547 Düsseldorf

Contact: [email protected]

Fig. 2

• As the ﬁtting is pressed into position in the centre of the plate, the long legs will engage with the top

surface of the ceiling, and the short legs will engage with the inner surface of the outer ring

• Remove the circlip ﬁtted into the lamp aperture in the bottom of the ﬁtting

• Fit a suitable lamp, max. 50W (not included)

• Insert the lamp into the centre of the ﬁtting and replace the circlip

• Switch on and check for correct operation

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage

the product.

This product is dimmable dependent on lamp type.

This product should be recycled in the correct manner when it reaches the end of its life. Check local

authorities for where facilities exist.

GENERAL

HCXX INSTRUCTIONS.indd 4HCXX INSTRUCTIONS.indd 4 02/05/2023 16:41:0902/05/2023 16:41:09

This product has a warranty of 1 year from date of purchase. Failure to install this product in accordance

with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch

code will invalidate the warranty. If this product should fail within its warranty period, it should be returned

to the place of purchase for a free of charge replacement. ML Accessories does not accept responsibility for

any installation costs associated with the replacement product. Your statutory rights are not affected. ML

Accessories reserve the right to alter product speciﬁcation without prior notice.

WARRANTY

HCXX INSTRUCTIONS.indd 5HCXX INSTRUCTIONS.indd 5 02/05/2023 16:41:0902/05/2023 16:41:09

DCMAY21_V2

ML Accessories Limited LU5 4LT

www.mlaccessories.co.uk

INTERNATIONAL

CONTACT DETAILS

INTERNATIONAL

CONTACT DETAILS

INTERNATIONAL

CONTACT DETAILS

HCXX INSTRUCTIONS.indd 6HCXX INSTRUCTIONS.indd 6 02/05/2023 16:41:1002/05/2023 16:41:10

ML Accessories HCBC User manual

ML Accessories HCBC User manual

ML Accessories HCBC User manual

Related papers

Other documents