Knightsbridge ODA1FSB is a dimmable LED downlight with a 5-year warranty, suitable for indoor use in residential or commercial settings. It has an IP20 rating, meaning it is not suitable for outdoor use or in areas with high moisture levels. With easy installation and a sleek design, the ODA1FSB provides efficient and customizable lighting for a variety of applications.
Knightsbridge ODA1FSB is a dimmable LED downlight with a 5-year warranty, suitable for indoor use in residential or commercial settings. It has an IP20 rating, meaning it is not suitable for outdoor use or in areas with high moisture levels. With easy installation and a sleek design, the ODA1FSB provides efficient and customizable lighting for a variety of applications.
INSTALLATION & MAINTENANCE MANUAL
ODA1FRxx / ODA1FSxx / ODA1TRxx
ODA1TSxx
These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following products:
ODA1FRxx / ODA1FSxx / ODA1TRxx / ODA1TSxx
GENERAL INSTRUCTIONS
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• Allow 50mm above and around the fitting for air dissipation (do not cover the fitting with insulation)
• This product is for indoor use only
• This product is Class I and must be earthed
• This product is IP20 rated
SAFETY
INSTALLATION
• Provide power to the required point of installation
• Cut a suitable hole in the mounting surface as per the cutout details (see Fig. 1) ensuring not to infringe with
any joists, gas/water pipes or electrical cables
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following products:
ODA1FRxx / ODA1FSxx / ODA1TRxx / ODA1TSxx
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• Allow 50mm above and around the fitting for air dissipation (do not cover the fitting with insulation)
• This product is for indoor use only
• This product is Class I and must be earthed
• This product is IP20 rated
INSTALLATION
• Provide power to the required point of installation
• Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring not to
infringe with any joists, gas/water pipes or electrical cables
Fig. 1
• Connect the luminaire to the mains supply ensuring the correct polarity is observed (see Fig. 2):
L – Live (brown), E – Earth (green/yellow), N – Neutral (blue). Two cables can be inserted into the
push-fit terminal block in order to achieve loop-in/loop-out wiring
Fig. 2
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following products:
AMA1TSxx / AMA2TSxx / AMA3TSxx / AMA4TSxx
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• Allow 50mm above and around the fitting for air dissipation (do not cover the fitting with insulation)
• This product is for indoor use only
• This product is Class II double insulated
• This product is IP20 rated
INSTALLATION
• Provide power to the required point of installation
• Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring not to
infringe with any joists, gas/water pipes or electrical cables
Fig. 1
• Connect the luminaire to the mains supply ensuring the correct polarity is observed (see Fig. 2):
L – Live (brown), E – Earth (green/yellow), N – Neutral (blue). The earth terminal is non-functional and
only provided for convenience. Two cables can be inserted into the push-fit terminal block in order to
achieve loop-in/loop-out wiring
Fig. 2
Fig. 1
Fig. 2
• Connect the luminaire to the mains supply ensuring the correct polarity is observed (see Fig. 2):
L – Live (brown), E – Earth (green/yellow), N – Neutral (blue). Two cables can be inserted into the push-fit
terminal block in order to achieve loop-in / loop-out wiring
• Lift both spring clips on the sides of the downlight and push into the ceiling
• Switch on and check for correct operation
Fig. 3
• Insert the terminal block bracket into the side of the spring clip on the downlight and add a suitable
LED GU10 lamp (see Fig. 3)
• Insert the terminal block bracket into the side of the spring clip on the downlight and add a suitable
LED GU10 lamp (see Fig. 3)
Fig. 3
• Lift both spring clips on the sides of the downlight and push into the ceiling
• Switch on and check for correct operation
GENERAL
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
This product is dimmable dependent on lamp type.
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist.
WARRANTY
This product has a warranty of 5 years from date of purchase. Failure to install this product in accordance with
the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will
invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of
purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve
the right to alter product specification without prior notice.
230V 50Hz, IP20, Class I, Dim, Non-IC, indoor only
AVNOV21_V1
• Insert the terminal block bracket into the side of the spring clip on the downlight and add a suitable
LED GU10 lamp (see Fig. 3)
Fig. 3
• Lift both spring clips on the sides of the downlight and push into the ceiling
• Switch on and check for correct operation
GENERAL
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
This product is dimmable dependent on lamp type.
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist.
WARRANTY
This product has a warranty of 5 years from date of purchase. Failure to install this product in accordance with
the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will
invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of
purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve
the right to alter product specification without prior notice.
230V 50Hz, IP20, Class I, Dim, Non-IC, indoor only
AVNOV21_V1
WARRANTY
This product has a warranty of 5 years from date of purchase. Failure to install this product in accordance with
the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will
invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place
of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve
the right to alter product specification without prior notice.
GENERAL
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
This product is dimmable dependent on lamp type.
This product should be recycled in the correct manner when it reaches the end of its life. Check local
authorities for where facilities exist.
AVNOV21_V1
ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
143
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
-
1
-
2
-
3
-
4
-
5
-
6
Knightsbridge ODA1FSB is a dimmable LED downlight with a 5-year warranty, suitable for indoor use in residential or commercial settings. It has an IP20 rating, meaning it is not suitable for outdoor use or in areas with high moisture levels. With easy installation and a sleek design, the ODA1FSB provides efficient and customizable lighting for a variety of applications.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Knightsbridge CSPT1BC User manual
-
Knightsbridge AMA3TSBC User manual
-
-
Knightsbridge EMPOWER3 User manual
-
Knightsbridge ORA1TSB User manual
-
Knightsbridge SPEKFCWA Installation guide
-
-
-
Other documents
-
ML Accessories VFCFIPW User manual
-
-
-
-
-
-
-
-
Eurolux D108SC Owner's manual
-