American Standard RU101SS Installation guide

RU101SS
American Standard
Brand
American Standard
Model
RU101SS
Category
Sanitary ware
Type
Installation guide
- 1 -
M965907 Rev. 1.2 (8/19)
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2019
Thank you for selecting American-Standard...
the benchmark of fine quality for over 140 years.
To ensure that your installation proceeds smoothly-please
read these instructions carefully before you begin.
RECOMMENDED TOOLS
ROUGHING-IN DIMENSIONS
n To assure proper positioning in relation to wall,
note roughing-in dimensions.
INSTALLATION
INSTRUCTIONS
RU101SS
RU102SS
RU107SS
RU108SS
RU109SS
RU107ESS
RU108ESS
Tubing Cutter Adjustable Wrench Channel Locks
Flat Blade Screwdriver
Plumbers' Putty or Caulking
Phillips Screwdriver
101 mm
(4")
89 mm
(3-1/2")
RU102SS
RU101SS
92 mm
(3-5/8")
123 mm
(4-7/8")
120 mm
(4-3/4")
150 mm
(5-7/8")
RU108SS
RU107SS
RU107ESS
92 mm
(3-5/8")
166 mm
(6-1/2")
RU109SS
92 mm
(3-5/8")
168 mm
(6-5/8")
OUTLETS
1/2" NOM.
COPPER SWEAT
or 1/2" NPT
92 mm
(3-5/8")
126 mm
(4-7/8")
INLETS
1/2" PEX
(ASTM F1960)
OUTLETS
1/2" NOM.
COPPER SWEAT
or 1/2" NPT
INLETS
1/2" NOM. CPVC
92 mm
(3-5/8")
126 mm
(4-7/8")
OUTLETS
1/2" NOM.
COPPER SWEAT
or 1/2" NPT
INLETS
1/2" PEX
(ASTM F1807-2)
RU108ESS
92 mm
(3-5/8")
166 mm
(6-1/2")
OUTLETS
1/2" NOM.
COPPER SWEAT
or 1/2" NPT
INLETS
1/2" PEX
(ASTM F1960)
1/2" NPT
FINISHED WALL
BOTTOM OF TUB
TOP OF
TUB RIM
4"
(102 mm)
1/2" NPT
7/8" TO 2"
(22 TO 50 mm)
2-3/4" MAX. (69 mm)
1-3/4" MIN. (45 mm)
OPTIONAL TO
FINISHED
FLOOR USUALLY
BETWEEN
65'' AND 78''
OUTLETS
1/2" STUB OUT
INLETS
1/2" STUB OUT
OUTLETS
1/2" NOM.
COPPER SWEAT
OR 1/2" NPT
INLETS
1/2" NOM.
COPPER SWEAT
OR 1/2" NPT
OUTLETS
1/2" NOM.
COPPER SWEAT
or 1/2" NPT
INLETS
1/2" PEX
(ASTM F1807-2)
PLASTER
GUARD
NOTE: TO AVOID SHOWER RISE OR
OTHER RELATED ISSUES, DO NOT
USE PEX CONNECTIONS AT THE TUB
OUTLET CONNECTING TO THE TUB
SPOUT.
Flash
™
Shower Valve Rough
With Screwdriver Stops
- 2 -
M965907 Rev. 1.2 (8/19)
STANDARD WALL INSTALLATION
1
CAUTION
Turn off hot and cold water
supplies before beginning.
COLD
1
2
3
WOOD
SCREWS
CROSS BRACE
HOT
6
8
SERVICE
STOPS
4"
(101 mm)
2 x 4
Cross
Brace
7/8" TO 2"
(22 mm to
50 mm)
3-1/2"
(100 mm)
2-3/4" MAX.
(69 mm)
1-3/4" MIN.
(45 mm)
SIDE VIEW
NOTE: TO AVOID SHOWER RISE OR
OTHER RELATED ISSUES, DO NOT
USE PEX CONNECTIONS AT THE TUB
OUTLET CONNECTING TO THE TUB
SPOUT.
n See Roughing-in diagram before starting.
n Remove the PLASTER GUARD (8) for proper installation.
n Mount VALVE BODY to cross brace (2" X 4") with-in wall. Use wood screws to secure VALVE BODY to brace.
n Connect HOT and COLD water supplies per connection method of selected valve.
n Connect RISER PIPE (1) to VALVE BODY (2) top outlet marked “UP”.
n Connect TUB FILLER PIPE (3) to bottom outlet.
n Install PLASTER GUARD (8) back onto the valve. Only remove PLASTER GUARD (8) when ready to install trim Kit.
n Finished wall should allow for a 4" diameter opening (Use PLASTER GUARD for guidance)
n Screw driver stops are primarly used to shut water off. To shut “HOT” or “COLD” water using a at head screw driver,
turn the head of the screw vertically. And to turn the water back on, turn the screw horizontally.
CAUTION: After valve installation, inspect the VALVE BODY for any debris. It can damage Pressure Balance
Valve cartridge.
NOTE: For back to back installation, follow steps mentioned above. Reversal of Hot/Cold water supplies is
accomplished by rotating cartridge (supplied with trim) 180° during installation.
- 3 -
M965907 Rev. 1.2 (8/19)
THIN WALL INSTALL
2
CAUTION
Turn off hot and cold water
supplies before beginning.
n See Roughing-in diagram before starting.
n Finished wall should allow for a 3-1/2" diameter opening (Use PLASTER GUARD for guidance).
n Remove PLASTER GUARD (8), rotate 90˚ counter clockwise and install the two screws. (Thin wall text should be on top)
n Use SELF-CENTERING HOLE GUIDES (9) as a guide for thin wall install.
n LOCKING SCREW (10) keeps valve in place when installing. Completely Thread LOCKING SCREW (10) onto
PLASTER GUARD (8).
n During the installation, make sure to position the Locking feature screw as shown in Figure A below. Once the valve is
positioned on the Thin Wall, turn counterclockwise as shown in Figure B to secure VALVE BODY (2) in place.
n Connect HOT and COLD water supplies per connection method of selected valve.
n Connect RISER PIPE (1) to VALVE BODY (2) top outlet marked “UP”.
n Connect TUB FILLER PIPE (3) to bottom outlet.
CAUTION: After valve installation, inspect the VALVE BODY for any debris. It can damage Pressure Balance
Valve cartridge.
NOTE: For back to back installation, follow steps mentioned above. Reversal of Hot/Cold water supplies is
accomplished by rotating cartridge (supplied with trim) 180° during installation.
COLD
1
2
3
HOT
10
6
3-1/2"
SIDE VIEW
8
9
Fig. B
Fig. A
UNLOCK
LOCK
10
10
Hex
Wrench
4 mm
- 4 -
M965907 Rev. 1.2 (8/19)
COLD
1
2
3
HOT
5
4
8
7
6
3-1/2"
SIDE VIEW
n Finished wall should allow for a 3-1/2" diameter opening.
n Discard or throw away PLASTER GUARD (8).
n Thread MOUNTING PLATE (4) on to the valve with the two SCREWS (5).
n Install Mounting Screws (7) through Escutcheon Holder (8) and into Threaded holes (6).
Tighten Mounting Screws (7) Securely.
Note: MOUNTING PLATE (4), Mounting Screws (7), Escutcheon Holder (8), and the two SCREWS (5) can be found
packaged with the Belshire Trim rather than the valve.
n Connect HOT and COLD water supplies per connection method of selected valve.
n Connect RISER PIPE (1) to VALVE BODY (2) top outlet marked “UP”.
n Connect TUB FILLER PIPE (3) to bottom outlet.
n Service stops are primarily used to shut water off. To shut “HOT” or “COLD” water using a at head screwdriver,
turn the head of the screw vertically. And to turn the water back on, turn the screw horizontally.
THIN WALL INSTALLATION FOR BELSHIRE TRIMS
3
CAUTION
Turn off hot and cold water
supplies before beginning.
- 5 -
M965907 Rev. 1.2 (8/19)
4
n Valve comes with Flush Plug that allows hot and cold supply lines to be ushed independently (without cross ow).
n Flush plug is shipped in Orientation A.
– ORIENTATION A directs cold water through the shower port and hot water through the tub port.
n Flush plug can be reversed to Orientation B.
– ORIENTATION B directs cold water through the tub port and hot water through the shower port.
n For shower only installation ush cold supply line rst in Orientation A. Then reverse to Orientation B and ush
hot supply line. Alternatively, the ush plug can be removed entirely to ush water through the valve body.
n To switch between orientations follow these steps:
– Unthread BONNET NUT (1).
– Rotate FLUSH PLUG (2) 90 degrees to desired orientation.
– Rethread BONNET NUT (1).
n Upon completion of ushing both hot and cold supply lines unthread BONNET NUT (1), remove FLUSH PLUG (2),
and rethread BONNET NUT (1).
2
1
2 2
ORIENTATION BORIENTATION A (as shipped)
SHOWER
TUB
COLDHOT
SHOWER
TUB
COLDHOT
TEST PROCEDURES FOR FLUSH PLUG
RU102SS
RU101SS RU107SS
RU108SS
1
4
2
1
2
1
2
2
1
3 3 3
050145-0070A
1/2" SWEAT PLUG
2
M970452-0070A
FIXATION RING KIT
1
M970453-0070A
LOCKING CAM
SCREW KIT
3
M970451-0070A
SCREWDRIVER
STOPS
4
M970453-0070A
LOCKING CAM
SCREW KIT
2
M970451-0070A
SCREWDRIVER
STOPS
3
M970452-0070A
FIXATION RING KIT
1
3
4 4
M954805-YYY0A
DEEP ROUGH-IN
KIT
PURCHASED SEPARATELY
RU108ESS
RU109SS
RU107ESS
1
2
1
2
1
2
3 3 3
4 4 4
MODEL NUMBERS
RU101SS
RU102SS
RU107SS
RU108SS
RU109SS
RU107ESS
RU108ESS
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are
trademarks of AS America, Inc.
© AS America, Inc. 2019
- 6 -
M965907 Rev. 1.2 (8/19)
Flash
™
Shower Valve Rough
With Screwdriver Stops
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

American Standard RU101SS Installation guide

RU101SS
American Standard
Brand
American Standard
Model
RU101SS
Category
Sanitary ware
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents