2. Barco
  3. F50 Panorama
F50 Panorama

Barco F50 Panorama User manual

  • Hello! I am an AI chatbot trained to assist you with the Barco F50 Panorama User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Sales Support - Projection
www.barco.com
Page 1 of 2
V1.0 – CMAD 07/15
F series SRP™ (Smear Reduction Processing)
GENERAL RELEASE APPROVED
‘F’ Series SRP™ (Smear Reduction Processing)
SRP™ (Smear Reduction Processing) is a feature on some Barco F series projectors.
F35 (including F35 AS3D) - UHP Lamp projectors.
Dependent upon colour wheel variant these projectors feature SRP™. Available settings are either
SRP Half, SRP Full or Off. The non-adjustable Dark Time increase setting is fixed at 8.3333 ms.
Settings can be enabled from the projector ‘On Screen User Menu’ (Picture \ RealColor \
BrilliantColor) or via external control.
Note - SRP™ on the F35 (including F35 AS3D) projector is available for 60Hz video sources only.
FL3x & FS3x - LED & LED + IR projectors.
These projectors feature SRP™. Available settings are either 6 ms or 8 ms Dark Time. Settings can
be enabled from the projector ‘On Screen User Menu’ (Picture \ RealColor \ BrilliantColor) or via
external control.
Note - SRP™ on the FL3x and FS3x projectors is available for 60Hz video sources only.
F50 - UHP Lamp projectors.
Dependent upon colour wheel variant these projectors feature SRP™. Available settings are either
SRP Half, SRP Full or Off. The non-adjustable Dark Time increase setting is fixed at 8.3333 ms for
60Hz and 4.1666 ms for 120Hz. Settings can be enabled from the projector ‘On Screen User Menu’
(Picture \ RealColor \ BrilliantColor) or via external control.
Note - SRP™ Full functionality on the F50 is disabled for 120Hz video sources (although still visible
Note - in the projector ‘‘On Screen User Menu’, SRP Half settings are applied when SRP™ Full is
Note – selected).
The table below provides an overview of the SRP™ features available on each projector:-
Projector Model
Supported Colour
Wheels
(where applicable)
6 ms Dark
Time
F35 Panorama (UHP)
(2560 x 1080)
VizSim & VizSim
Bright
N/A
F35 (UHP)
(WQXGA)
VizSim & VizSim
Bright
N/A
F35 AS3D (UHP)
(HD / WUXGA)
N/A
N/A
FL32 (LED)
(HD / WUXGA)
N/A
Yes
FL33 (LED)
(HD / WUXGA)
N/A
Yes
FS33 (LED + IR)
(HD / WUXGA)
N/A
Yes
FL35 (LED)
(HD / WUXGA / WQXGA)
N/A
Yes
FS35 (LED + IR)
(WUXGA / WQXGA)
N/A
Yes
F50 (UHP) – 60Hz
(HD / WUXGA / 2560 x 1080 / WQXGA)
F50 (UHP) – 120Hz
(HD / WUXGA / 2560 x 1080 / WQXGA)
VizSim & VizSim
Bright
VizSim & VizSim
Bright
N/A
N/A
N/A
N/A
Sales Support - Projection
www.barco.com
Page 2 of 2
V1.0 – CMAD 07/15
F series SRP™ (Smear Reduction Processing)
GENERAL RELEASE APPROVED
Dark Time side effects explained.
Increasing Dark Time has an adverse effect on projector brightness. For example increasing
Dark Time by 8.3333 ms represents exactly half of the 16.6666 ms video frame interval at
60Hz, brightness subsequently reduced by 50% as a result.
It is important to note that although brightness is reduced full colour bit depth is retained.
In order to recover some brightness colour wheel spokes are enabled by default when SRP™
Half and Full settings are applied. This default setting can be over ridden by enabling SRP in the
projector Service Menu (Settings \ Service) if required.
SRP™ Half and Full explained.
SRP™ Half and SRP™ Full both introduce 8.3333 ms Dark Time. Colour wheel sequencing
differs between the two modes of operation to give a different visual effect. Results are
subjective and therefore the mode selected is entirely at the discretion of the end user.
Respective colour wheel sequences are RGB, blank for SRP™ Half and RGB, RGB blank / blank
for SRP™ Full. For reference SRP™ Full behaviour is comparable to FL3x series 8 ms Dark Time
setting in so much as it introduces some image flicker.
Using SRP™ with the projector in stereoscopic (3D) mode.
Using SRP™ with the projector in stereoscopic (3D) mode (where applicable) is not supported.
/