Vitek VTC-TNT5RFE-2 User manual

VITEK

OPERATION MANUAL

Transcendent IP

5MP Cameras

Transcendent Series 5 Megapixel

Indoor/Outdoor WDR IP

Cameras with IR Illumination

FEATURES

• 1/2.5” 5 Megapixel Progressive Scan CMOS image sensor

• Up to 30fps live view @ 5 MegaPixel (2592x1944)

• Motorized Varifocal & Fixed Lens Options

• Infrared LED

Illumination

• 120dB Super Wide Dynamic Range (WDR)

• True Mechanical Day/Night function by ICR

• XD-DNR (2D-DNR & 3D-DNR) Noise Reduction

• Fully Programmable Intelligent Analytics including Face Detection,

Object Removal/Museum Search, Exception, Line Crossing, Area

Intrusion, People Counting, People Intrusion, Crowd Density Monitoring

• H.265/H.264/MJPEG Triple Streaming

• Secondary Video Output (CVBS)

• Remote Viewing via CMS, Internet Explorer, and iOS & Android Apps

• IP66 Weather Resistance *IK10 Impact Rating on select Dome Units

• ONVIF Compliant

• Charcoal Finish Available on Select Models

• Optional Mounts Available - see page 51 for details

• 12VDC & PoE (Power over Ethernet) Operation

Transcendent IP Cameras v4: Operation Manual

1

n Please use the specified power supply to connect.

n Do not attempt to disassemble the camera; in order to prevent electric shock, do not remove

screws or covers.

n There are no user-serviceable parts inside. Please contact the nearest service center as soon as

possible if there is any failure.

n Avoid incorrect operation, shock, and vibration, which can cause damage to

product.

n Do not use corrosive detergent to clean main body of the camera. If necessary, p

lease use soft dry

cloth to wipe dirt; for hard contamination, use neutral detergent. Any cleanser for high grade

furniture is acceptable.

n Avoid aiming the camera directly towards extremely bright lights or the sun, as this may

damage the image sensor.

n Please follow these instructions to install the camera. Do not reverse the camera, or the reversed

image will be received.

n Do not o

perate when temperature, humidity and power supply are beyond limited stipulations.

n Keep away from heat sources such as radiators, heat registers, stove, etc.

n Do not expose the product to direct airflow from an air conditioner.

n These are product instructions only, not a quality warranty. We reserve the rights of amending

typographical errors, inconsistencies with the latest version, software upgrades and product

impr

ovements, interpretation and modification. These changes will be published in the latest

version without special notification.

n When this product is in use, the relevant contents of Microsoft, Apple and Google will be

involved in. The pictures and screenshots in this manual are only used to explain the usage of our

product. The ownerships of trademarks, logos and other intellectual properties related to

Microsoft, Apple and Google belong to the above-mentioned companies.

n This

manual is suitable for IR IP66 and 67 network cameras. All pictures and examples used in the

manual are for reference only.

Transcendent IP Cameras v4: Operation Manual

2

Table of Contents

1 Introduction................................................................................................4

2 IE Remote Access......................................................................................5

2.1 LAN.....................................................................................................5

1.1.1 Access through IP-Tool...................................................................5

1.1.2 Directly Access through IE..............................................................7

2.2 WAN....................................................................................................8

3 Remote Preview........................................................................................11

4 Remote Live Surveillance........................................................................12

1.2 System Configuration.....................................................................12

1.2.1 Basic Information.........................................................................12

1.2.2 Date and Time.............................................................................12

1.2.3 Local Config................................................................................13

1.2.4 Storage................................................................................................13

1.2.5 SD Card Management...............................................................13

1.2.6 Snapshot Settings......................................................................14

1.3 Image Configuration.......................................................................14

1.3.1 Display Configuration..................................................................14

1.3.2 Video / Audio Configuration........................................................16

1.3.3 OSD Configuration.....................................................................17

1.3.4 Video Mask................................................................................17

1.3.5 ROI Configuration......................................................................18

1.3.6 Lens Control..............................................................................18

1.4 Alarm Configuration.......................................................................19

1.4.1 Motion Detection.....................................................................19

1.4.2 Alarm In.................................................................................21

1.4.3 Alarm Out...............................................................................21

1.4.4 Alarm Server.........................................................................22

1.5 Event Configuration.......................................................................22

1.5.1 Object Removal.......................................................................22

1.5.2 Exception.................................................................................23

1.5.3 Line Crossing.........................................................................24

1.5.4 Intrusion................................................................................26

1.5.5 Crowd Density Detectiion.....................................................27

1.5.6 People Intrusion...................................................................27

1.5.7 People Counting..................................................................27

1.5.8 Face Detection....................................................................29

1.6 Network Configuration...................................................................30

1.6.1 TCP/IP......................................................................................30

1.6.2 Port..........................................................................................31

1.6.3 Server Configuration................................................................31

1.6.4 DDNS......................................................................................31

1.6.5 SNMP......................................................................................32

1.6.6 802.1x.....................................................................................33

1.6.7 RTSP......................................................................................33

1.6.8 Multicast Address...................................................................33

1.6.9 UPNP.....................................................................................34

1.6.10 Email....................................................................................34

1.6.11 FTP.......................................................................................34

1.6.12 HTTPS.................................................................................35

Table of Contents (Continued)

4.1 Security Configuration.................................................................................36

1.6.13 User Configuration.........................................................................36

1.6.14 Online User....................................................................................37

1.6.15 Block and Allow Lists.....................................................................37

4.2 Maintenance Configuration..........................................................................37

1.6.16 Backup and Restore.........................................................................37

1.6.17 Reboot.............................................................................................38

1.6.18 Upgrade..........................................................................................38

16.6.19 Operation Log.............................................................................39

5 Record Search..........................................................................................................40

5.1 Photo Search.................................................................................................40

5.2 Photo Search.................................................................................................40

5.3 Video Search.................................................................................................41

16.6.20 Local Video Search.............................................................................41

16.6.21 SD Card Video Search........................................................................42

6 Specifications..........................................................................................................43

Transcendent IP Cameras v4: Operation Manual

3

Transcendent IP Cameras v4: Operation Manual

4

1 Introduction

This IP c

amera is designed for high performance CCTV solutions. It adopts state of the art video

processing chips. It utilizes most advanced technologies, such as video encoding and decoding

technology, complies with the TCP/IP protocol, SoC, etc to ensure this system is more stable and

reliable.

Main Features

l ICR auto switch, true day/night

l 3D DNR, digital WDR, ROI coding

l Support BLC, HLC, Defog, Anti-flicker

l Supports smart phone, table, remote monito

ring

l Supports Face Detection

Surveillance Application

Transcendent IP Cameras v4: Operation Manual

5

2 IE Remote Access

2.1 LAN

In LAN, there are two ways to access the IP-Cam: 1. access through IP-Tool; 2. directly access through

IE browser.

1.1.1 Access through IP-Tool

Network connection:

Make sure the PC and IP-Cam are connected to the LAN and the IP-Tool is installed in the PC from

the CD.

Double click the IP-Tool icon on the desktop to run this software as shown below:

Modify the IP address. The default IP address of this camera is 192.168.226.201. Click the

information of the camera listed in the above table to show the network information on the right side.

Modify the IP address and gateway of the camera and make sure its network address is in the same

local network segment as that of the computer. Please modify the IP address of your device according

to the practical situation.

(2)

(3)

(1)

If

Transcendent IP Cameras v4: Operation Manual

6

For example, the IP address of your computer is 192.168.1.4. So the IP address of the camera shall be

changed to 192.168.1.X. After modification, please input the ADMIN password of the administrator

and click “Modify” button to modify the setting.

F

Double cl

ick the IP address and then the system will pop up IE browser to connect IP-CAM. IE

browser will ask to download the Active X control. After downloading, a login window will pop up

as

shown below.

Input the username and password to log in.

F

The default password of the administrator is “123456”.

The default username is “admin”; the default password is “123456”.

(4)

1.1.2 Directly Access through IE

The default network settings are as shown below:

IP address: 192.168.226.201

Subnet Mask: 255.255.255.0

Gateway: 192.168.226.1

HTTP: 80

Data port: 9008

Transcendent IP Cameras v4: Operation Manual

7

The

system will prompt the above-mentioned textbox to ask you to change the default

password.

It is strongly recommended to change the default password for account security. If

“

Do not show again” is checked, the textbox will not be prompted next time.

You may use the above default settings when you log in the camera for the first time. You may directly

connect the camera to the computer through network cable.

Manually set the IP address of the PC as the network segment should be as the same as the default

settings of the IP camera. Open the network and share center. Click “Local Area Connection” to pop

up the following window.

Select “P

roperties” and then select internet protocol according to the actual situation (for example:

IPv4). Next, click “Properties” button to set the network of the PC.

(1)

Transcendent IP Cameras v4: Operation Manual

8

Open IE bro

wser and input the default address of IP-CAM and confirm. IE browser will ask to

download the Active X control.

After downloading the Active X control, the login dialog box will pop up.

Input the default username and password and then enter to view.

2.2 WAN

Ø Access through the router or virtual server

Make sure the camera is connected via LAN and then log into the camera via LAN and go to

ConfigàNetworkàPort to set the port number.

Port Setup

Go to ConfigàNetworkàTCP/IP menu to modify the IP address.

(2)

(3)

(4)

(1)

(2)

Transcendent IP Cameras v4: Operation Manual

9

IP Setup

Go to the r

outer’s management interface through IE browser to forward the IP address and port of

the camera. Please check your router manual for instructions on port forwarding.

Router Setu

p

Open IE browser and input its WAN IP and http port to access.

Ø Access through PPPoE dial-up

Network connection

You may access the ca

mera through PPPoE auto dial-up. The setting steps are as follow:

Go to ConfigàNetworkàPort to set the port number.

(3)

(4)

(1)

Transcendent IP Cameras v4: Operation Manual

10

Go to ConfigàNetworkàTCP/IPà PPPoE Config menu. Enable PPPoE and then input the user

name and password which you can get from your internet service provider.

Go to ConfigàNetworkàDDNS menu. Before you configure the DDNS, please apply for a

domain name first. Please refer to DDNS configuration for detail information.

Open IE browser and input the domain name and http port to access.

Ø Access through static IP

Network c

onnection

The setting steps are as follow:

Go to Co

nfigàNetworkàPort to set the port number.

Go to ConfigàNetworkàTCP/IP menu to set the IP address. Check “Use the

following IP address”

and then input the static IP address and other parameters.

Open IE browser and input its WAN IP and http port to access.

(2)

(3)

(4)

1.

2.

3.

Transcendent IP Cameras v4: Operation Manual

11

3 Remote Preview

After you log in, you will see the following window.

The following table is the instructions of the icons on the remote live interface.

Icon Description Icon Description

Original size Scene change indicator icon

Appropriate size Abnormal clarity indicator icon

Auto Color abnormal indicator icon

Full screen Motion alarm indicator icon

Start/stop live view Start/stop recording

Enable/disable audio Zoom in

Snap Zoom out

l

When motion detection alarm is triggered, the people icon will turn red.

l In full screen mode, double click to exit.

l icons may not be displayed for some versions without intelligent analysis function.

Transcendent IP Cameras v4: Operation Manual

12

4 Remote Live Surveillance

1.2 System Configuration

The “System” configuration includes four submenus: Basic Information, Date and Time, Local Config

and storage.

1.2.1 Basic Information

In the “Basic Information” interface, you can check the relative information of the device.

1.2.2 Date and Time

Go to ConfigàSystemàDate and Time. Please refer to the following interface.

You can select the time zone and D

ST as required.

Click “Date and Time” tab to set the time mode.

Transcendent IP Cameras v4: Operation Manual

13

1.2.3 Local Config

Go to Config(use right arrow)System(use right arrow)Local Config to set up the storage path of

captured pictures and recorded videos on the local PC. There is also an option to enable or disable

the bitrate display in the recorded files.

1.2.4 Storage

Go to ConfigàSystemàStorage to go to the interface as shown below.

Go to ConfigàSystemàStorageàRecord to go to the interface as shown below

Additionally, local face information storage can be enabled here:

1.2.5 SD Card Management

Click “Format” to format the SD card. All data will be cleared by clicking this button.

Click “Eject” to stop writing data to SD card. Then the SD card can be ejected safely.

Snapshot Quota: Set the capacity proportion of captured pictures on the SD card.

Video Quota: Set the capacity proportion of record files on the SD card.

card record stream. Set the pre record time if you enable pre record. Click “Save” button to save the

settings.

Pre Record Time: Set the time to record before the actual recording begins.

Set schedule recording. Check “Enable Schedule Record” and set the schedule.

Transcendent IP Cameras v4: Operation Manual

14

1.3

Image Configuration

Image Configuration includes Display, Video/Audio, OSD, Video Mask, ROI Config and

Zoom/Focus.

1.3.1 Display Configuration

Go to ImageàDisplay interface as shown below. You can set and adjust the picture’s brightness,

contrast, hue and saturation, etc.

1.2.6 Snapshot Settings

Go to ConfigàSystemàStorageàSnapshot to go to the interface as shown below

Set the format, resolution and quality of the image saved on the SD card and the snapshot interval and quantity and

the timing snapshot here.

Snapshot Quantity: The number you set here is the maximum quantity of snapshots. The actual quantity of

snapshots may be less than this number. Supposing the occurrence time of an alarm event is less than the time of

capturing pictures, the actual quantity of snapshots is less than the set quantity of snapshots.

Timing Snapshot: Enable timing snapshot first and then set the snapshot interval and schedule. The

setup steps of schedule are the same as the schedule recording (See “Schedule Recording”).

Transcendent IP Cameras v4: Operation Manual

15

Brightness: Set the brightness level of the camera’s image.

Contrast: Set the color difference between the brightest and darkest parts.

Hue: Set the total color degree of the image.

Saturation: Set the degree of color purity. The purer the color, the brighter the image is.

WDR: WDR can adjust the camera to provide a better image when there are very bright

and very dark areas simultaneously in the field of view by lowering the brightness of the

bright area and increasing the brightness of the dark area.

Sharpness: Set the resolution level of the image plane and the sharpness level of the image edge.

Noise Reduction: Decrease the noise and make the image more thorough. Increasing the

value will make the noise reduction effect better but it will

reduce the image

resolution. Defog: Activating this function and setting an appropriate value as needed

in foggy, dusty, smoggy or rainy environment to get clearer images.

Backlight Compensation (BLC):

à Off: disables the backlight compensation function. It is the default mode.

à HLC: lowers the brightness of the entire image by suppressing the brightness of the

image’s bright area and reducing the size of the halo area.

à BLC: If enabled, the auto exposure will activate according to the scene so that the object

of the image in the darkest area will be seen better.

Antiflicker:

à Off: disables the anti-flicker function. This is used mostly in outdoor installations.

à 50Hz: reduces flicker in 50Hz lighting conditions.

à 60Hz: reduces flicker in 60Hz lighting conditions.

Smart IR: This function can effectively avoid image overexposure and underexposure by

controlling the brightness of the IR lights according to the actual conditions to make the i

mage more realistic. Please enable it as needed.

White Balance: Adjust the color temperature according to the environment automatically.

Frequency: 50Hz and 60Hz can be optional.

Day/night Mode: Please choose the mode as needed.

Auto= will change to Black & White in low light

Day= Camera will be in color all the time

Night= Camera will be in Black & White all the time

Schedule= set a particular time the camera switches to Night mode or Day mode

Exposure Mode: Choose “Auto” or “Manual”. If manual is chosen, the digital shutter speed

can be adjusted.

Corrid

or Pattern: Corridor viewing modes can be used for situations such as long hallways.

0, 90, 180 and 270 are available. The default value is 0. The video resolution should be 1080P

or below if this function is used.

Image Mirror: Turn the current video image horizontally.

Image Flip: Turn the current video image vertically.

Schedule Settings of Image Parameters:

Click the “Schedule” tab as shown below

1.3.2 Video / Audio Configuration

Go to ImageàVideo / Audio interface as shown below. In this interface, you can set the resolution,

frame rate, bitrate type, video quality etc. subject to the actual network condition.

Transcendent IP Cameras v4: Operation Manual

16

Click “Audio” tab to go to the interface shown here.

Three video streams can be adjustable.

Resolution: The higher the resolution is, the clearer the image is.

Frame rate: The higher the frame rate is, the more fluid the video is. However, more storage will

be used.

Bitrate type: Including CBR and VBR. CBR means that no matter how the video changes, the

compression bitrate keeps constant. This will not only facilitate the image quality better in a constant

bitrate but also help to calculate the capacity of the recording. VBR means that the compression bitrate

can be adjustable according to the change of the video resources. This will help to optimize the

network bandwidth.

Bitrate: Please choose according to the actual network situation.

Video Quality: When VBR is selected, you need to choose image quality. The higher the image

quality you choose, the more bitrate will be required.

I Frame interval: It is recommended to use the default value. If the value is to high, the read speed of

the g

roup of pictures will be slow resulting in the quality loss of the video.

Video Compression: H264 and H265 are optional. Higher quality of image can be transferred under

limited network bandwidth by using H265 video encoding; however, higher quality of the hardware is

required.

Profile: Baseline, main/high profiles are optional. Baseline profile is mainly used in interactive

application with low complexity and delay. Main/high profile is mainly used for higher coding

requirement.

Send Snapshot: Please select according to the actual situation.

Video encode slice split: If enabled, you may get a more fluid image even though using a

low-performance PC.

Watermark: If enabled, input the watermark content. You may check the watermark when playing

back the

local recording in the search interface, unless the recording file has been tampered with.

Audio Encoding: G711A and G711U are selectable.

Audio Type: MIC and LIN are selectable.

Set full time schedule for common, day, night mode and specified time schedule for day and night.

Choose “Timing” in the drop-down box of schedule as shown below.

Transcendent IP Cameras v4: Operation Manual

17

1.3.3 OSD Configuration

Go to ImageàOSD interface as shown below.

You can set the time stamp, device name and OSD content here. After enabling the corresponding display

and entering the content, drag them to change their position. Then click “Save” button to save the settings.

1.3.4 Video Mask

Go to ImageàVideo Mask interface as shown below. You can set 4 mask areas at most.

To set up video mask:

1. Enable video mask.

2. Click “Draw Area” button and then drag the mouse to draw the video mask area.

3. Click “Save” button to save the settings.

4. Return to live view to see the following picture.

Clear the video mask:

Go to

video mask interface an

d the

n

click

“

C

lear” button to delete the current video mask area.

Transcendent IP Cameras v4: Operation Manual

18

1.3.5 ROI Configuration

Go to ImageàROI Config interface as shown below.

1. Check “Enable” and then click “Draw Area” button.

2. Drag the mouse to set the ROI area.

3. Set the level.

4. Click “Save” button to save the settings.

Now, you will see the selected ROI area is clearer than other areas especially in a low bitrate condition.

1.3.6 Lens Control

This function is only available for the model with motorized zoom lens. Within this section, zoom and

focus can be controlled. If the image is out of focus after a manual adjustment, one key focus can be

used to set the focus automatically.

Transcendent IP Cameras v4: Operation Manual

19

1.4 Alarm Configuration

Alarm configuration includes

two submenus: Motion Detection and Alarm Server.

1.4.1 Motion Detection

Go to AlarmàMotion Detection to set motion detection alarm.

1. Check “Enable Alarm” check box to activate motion

based alarm, choose alarm holding time and set

alarm trigger options.

Trigger Snap: If selected, the system will snap images on an alarm and save them

to the SD

card.

Trigger SD Recording: If selected, the recording will be triggered and saved to the

SD card on an

alarm (this function is only available for the models with SD card slot).

Trigger Email: If “Trigger Email” and “Attach Picture” checkbox is checked (email address shall be

set first in the Email configuration interface), the captured pictures and triggered event will be sent to

those addresses.

Trigger FTP: If “Trigger FTP” and “Attach Picture” checkbox is checked, the captured pictures will

be sent to the FTP server address. Please refer to FTP configuration chapter for more details.

2. Set motion detection area and sensitivity. Click “Area and Sensitivity” tab to go to the interface as

shown below.

Alarm Out: If selected, this would trigger an external relay output that is connected to the camera on

detecting a motion based alarm.

Move the “Sensitivity” scroll bar to set the sensitivity.

Select “Add” and click “Draw” button and drag mouse to select the motion detection area; Select

“Erase” and drag the mouse to clear motion detection area.

Select “Select All” to select the whole image for motion

Select “Clear All” to undo the whole picture

Select “Invert” to reverse the motion area

After that, click “Save” to save the settings.

Page is loading ...

Vitek VTC-TNT5RFE-2 User manual

Vitek VTC-TNT5RFE-2 User manual

Related papers

Other documents