Avent SCF355/00 User manual

Specications are subject to change without notice

4213 354 36418

SCF355

Page is loading ...

6

General description (Fig. 1)

1. Bottle warmer

2. Light

3. Settings knob

4. O setting

5. Defrost setting

6. Keep warm setting

7. Express milk warming setting for contents up to

180ml/6oz

8. Food warming setting

9. Express milk warming setting for contents over and

including 180ml/6oz

Important

To fully benet from the support that Philips oers, register

your appliance at www.philips.com/welcome.

Read this user manual carefully before you use the bottle

warmer and save it for future reference.

Danger

- Do not immerse the cord, plug or appliance in water or

other liquid.

Warning

- Only use the appliance indoors.

- Do not let the mains cord hang over the edge of a table or

worktop. Excess cord can be stored in the base of the

bottle warmer.

- Keep the mains cord away from hot surfaces.

- Only connect the appliance to an earthed wall socket.

Always make sure that the plug is inserted into the wall

socket properly.

- Check if the voltage indicated on the bottom of the

appliance corresponds to the local mains voltage before

you connect the appliance.

ENGLISH

- If you need to use an extension cord, make sure it is an

earthed extension cord with a rating of at least 13

amperes.

- Do not use the appliance if the plug, the mains cord or the

appliance itself is damaged. If the mains cord is damaged,

you must have it replaced by Philips, a service centre

authorised by Philips or similarly qualied persons in order

to avoid a hazard.

- Do not place the appliance on or near a hot gas or electric

cooker, or in a heated oven.

- This appliances can be used by persons with reduced

physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given

supervision or instruction concerning use of the appliance

in a safe way and understand the hazards involved.

- Cleaning and user maintenance shall not be made by

children.

- Children should be supervised to ensure that they do not

play with the appliance.

- Keep the appliance and its cord out of the reach of

children.

- Do not spill water on the mains plug.

- Only use the appliance as described in the user manual to

avoid potential injury due to misuse.

- Do not preheat the appliance.

- Always place a fully assembled bottle with cap in the

bottle warmer before you add water.

- Make sure you add water before you switch on the bottle

warmer.

- Hot water can cause serious burns. Be careful when the

bottle warmer contains hot water.

- The accessible surfaces of the appliance may become hot

during use and are subject to residual heat after use.

- Do not move the appliance when it contains hot water.

ENGLISH 7

- When the food or milk has reached the required

temperature, remove the bottle or container from the

bottle warmer. If you leave food or milk in the bottle

warmer, the temperature of the food or milk increases.

- Always check the food temperature before you feed your

child.

Caution

- This appliance is intended to be used in household and

similar applications such as farm houses, bed and

breakfast type environments, sta kitchen areas in shops,

oces and other working environments, and by clients in

hotels, motels and other residential type environments.

- Unplug the appliance when it is not in use.

- The surface of the heating element is subject to residual

heat after use.

- Let the appliance cool down before you clean it.

- Follow the descaling instructions to avoid irreparable

damage.

- Do not try to open or repair the appliance yourself. You

can contact the Philips Consumer Care Centre in your

country (see www.philips.com/support).

- The food should not be heated for too long.

You can nd the production date code YYWW in the cord

storage compartment in the base of the bottle warmer.

Electromagnetic elds (EMF)

This Philips appliance complies with all applicable standards

and regulations regarding exposure to electromagnetic elds.

Using the bottle warmer

With this bottle warmer, you can safely warm all Philips Avent

feeding bottles and milk/baby food in containers and other

baby food jars.

Note: Philips Avent breast milk bags and Philips Avent

2oz/60ml bottles cannot be used in this bottle warmer.

ENGLISH8

Explanation of settings

- O setting: The bottle warmer is switched o and the light

is o. On every other setting, the appliance is switched on

and the light is lit (Fig. 2).

- Express milk warming setting for contents up to

180ml/6oz: Select this setting when you want to quickly

warm a bottle of milk with a content up to 180ml/6oz.

The bottle has to be taken out immediately after warming

to the right temperature, otherwise the milk will be

overheated.

- Food warming setting: Select this setting when you want

to warm a container/jar of baby food.

- Express milk warming setting for contents over and

including 180ml/6oz:

Select this setting when you want to quickly warm a bottle

of milk with a content over and including 180ml/6oz.

The bottle needs to be taken out immediately after

warming to the right temperature, otherwise the milk will

be overheated.

- Keep warm setting: Milk is warmed at a slower speed and

be kept at right temperature.

- Defrost setting: Defrost a bottle/container of milk/baby

food to liquid state. No warming occurs.

Using the bottle warmer with express milk warming

setting

1 Put the mains plug in the wall socket (Fig. 3).

2 Place a bottle in the bottle warmer (Fig. 4).

3 Fill the bottle warmer with drinking water up to the level

of the milk in the bottle. In case of large amounts of milk,

the maximum level of water is approximately 1 cm below

the top of the bottle warmer. An accurate water level

ensures correct warming performance (Fig. 5).

ENGLISH 9

4 Select the desired setting based on the milk volume. See

the express warming reference table at the end of this

chapter to check how long the milk needs to be warmed

in the selected setting (Fig. 6).

Note: The speed of warming milk depends on the amount of

the milk warmed and on its initial temperature, i.e. room

temperature (20°C) or fridge temperature (5°C).

5 The orange light goes on when you select a setting. This

indicates that the bottle warmer is on (Fig. 7).

Note: Whilst warming the milk circulates and heats evenly.

6 Check the express warming reference table for the time

required to warm the milk. Remove the bottle from the

bottle warmer after the time indicated in the express

warming reference table has passed (Fig. 8).

Tip: When you nd the milk is not warm enough, you can

place the bottle back into the appliance for a maximum of

30 seconds of extra warming. This will create a slightly

warmer result but without overheating.

Caution: If you leave the bottle in the bottle warmer longer

than the time indicated in the settings table, the milk may

become overheated.

Note: If you overheat breast milk, valuable nutrients and

vitamins may be lost.

7 Always check the temperature before you feed your

baby. Gently shake the bottle or milk storage container

and check the temperature of the milk by sprinkling a

few drops on the inside of your wrist (Fig. 9).

8 Turn the knob back to the ‘o’ position (Fig. 10).

Caution: The water in the bottle warmer might be hot after

nishing warming milk / baby food. Be careful that hot water

can cause serious burns.

If you do not turn the knob back to the ‘o’ position, the water

keeps heating up and will reach a very high temperature.

ENGLISH10

Express warming reference table

ml/oz min min

5°C/40°F 20°C/70°F

60 ml/2 oz-90 ml/3 oz 4.5 3.0

90 ml/3 oz-110 ml/3.7 oz 5.5 3.0

125 ml/4 oz-150 ml/5 oz 3.5 3.0

180 ml/6 oz-210 ml/7 oz 5.5 4.0

240 ml/8 oz-260 ml/9 oz 7.0 4.5

290 ml/10 oz-330 ml/11 oz 7.5 5.0

Note: The indicated warming times are based on Philips

Avent Classic and Natural PP bottle ranges. Be aware that

warming timings of Philips Avent standard bottles and glass

bottles deviate from these indications. The characteristics

of bottles such as material or thickness may also impact the

warming times, therefore it may take less time to warm a

larger volume of milk.

Note: The milk may feel cool to you, but for a newborn baby

its temperature is very pleasant.

Using the bottle warmer to warm baby food

1 Follow the same steps as indicated in the previous

paragraph.

2 Make sure to stir the baby food during warming as it

does not circulate automatically. Be careful not to burn

your ngers when holding the container/jar while stirring

(Fig. 11).

ENGLISH 11

After warming test the baby food with a spoon to ensure it is

not too hot. If the baby food is not warm enough, put the

container back into the bottle warmer and warm the baby

food until it has the desired temperature.

Note: Due to the high variety of baby food consistencies, it

is strongly recommended to continuously stir and check

while you are warming the baby food for an optimal result.

Note: Due to the high variety of baby food consistencies, it

is not possible to indicate warming timings for baby food.

Using the keep warm setting to warm milk

1 Put the mains plug in the wall socket (Fig. 3).

2 Place the bottle or container in the bottle warmer (Fig. 4).

3 Fill the bottle warmer with drinking water up to the level

of the milk in the bottle/container. In case of large

amounts of milk, the maximum level of water is

approximately 1 cm below the top of the bottle warmer

(Fig. 5).

4 Select the position of keep warm (Fig. 6).

At this setting, you can warm your milk at a slow pace and

keep it warm at the right end temperature. E.g. to warm a

bottle of 4oz milk starting from room temperature, it will take

15-20min. The warming time may be longer or shorter

depends on the milk volumes and starting temperature.

Note: Philips Avent recommends to feed your baby as soon

as possible after the milk is warmed. We advise not to

reheat the milk after it has cooled down again.

Note: Always check the temperature before you feed your

baby (Fig. 9).

5 Turn the knob back to the ‘o’ position when the bottle/

container is removed from the bottle warmer (Fig. 10).

ENGLISH12

Using the bottle warmer with defrost setting

1 Put the mains plug in the wall socket (Fig. 3).

2 Place the bottle or container in the bottle warmer (Fig. 4).

3 Fill the bottle warmer with drinking water up to the level

of the milk/baby food in the bottle/container. In case of

large amounts of milk/baby food, the maximum level of

water is approximately 1 cm below the top of the bottle

warmer (Fig. 5).

4 Select the position of defrost (Fig. 6).

At this setting, your frozen milk/baby food can be defrosted

till liquid state.

For frozen milk, check the warming reference table for the

expected defrost timings, as indication one small and one

larger milk volume are included in the table. After your milk is

defrosted, choose express warming setting or keep warming

setting to warm your milk. Please refer to the previous

chapters for usage instructions. Consider the start

temperature of your milk around fridge temperature for the

warming timings as rough guideline.

ml/oz hours

60 ml/2 oz-90 ml/3 oz 1-1.5

180 ml/6 oz-210 ml/7 oz 1.5-2.5

5 You may also defrost baby food in Philips Avent food

container by this setting. After your baby food is

defrosted, choose food warming setting to warm it.

Please refer to the previous chapter for usage instruction.

Note: Due to the high variety of baby food consistencies, it

is strongly recommended to continuously stir and check

while you are defrosting the baby food for an optimal result.

Note: Due to the high variety of baby food consistencies, it

is not possible to indicate warming timings for baby food.

ENGLISH 13

Cleaning and descaling

Cleaning

1 After each use, unplug the bottle warmer and let it cool

down (Fig. 12).

2 Remove the water from the bottle warmer for hygienic

reasons (Fig. 13).

3 Wipe the outside and inside of the bottle warmer with a

moist cloth (Fig. 14).

Do not use abrasive, anti-bacterial cleaning agents,

chemical solvents or sharp tools to clean the bottle warmer.

Note: If you used the bottle warmer to warm containers with

baby food, make sure that no spilled baby food remains on

the bottom of the bottle warmer.

Descaling

It is recommended to descale the bottle warmer every four

weeks to ensure it continues to work eciently.

1 Mix 50ml/1.7oz of white vinegar with 100ml/3.4oz of cold

water to descale the bottle warmer. Switch on the bottle

warmer, select the milk warming setting for contents

under 180ml/6oz and let the appliance operate for 10

minutes. Leave the solution in the bottle warmer until all

scale has dissolved (Fig. 15).

Note: You can also use citric acid based descalers.

Note: Do not use other types of descalers.

2 Unplug the bottle warmer before you empty it (Fig. 12).

3 Empty the bottle warmer and rinse its inside thoroughly.

If you still see traces of scale after rinsing, repeat the

descaling procedure (Fig. 13).

ENGLISH14

Recycling

Do not throw away the product with the normal household

waste at the end of its life, but hand it in at an ocial

collection point for recycling. By doing this, you help to

preserve the environment.

Follow your country’s rules for the separate collection of

electrical and electronic products. Correct disposal helps

prevent negative consequences for the environment and

human health.

Guarantee and support

If you need information or support, please visit

www.philips.com/support or read the separate worldwide

guarantee leaet.

ENGLISH 15

Page is loading ...

注意：

您也可以使用含檸檬酸的除垢劑。

注意：

請勿使用其他類型的除垢劑。

2

請先拔除插頭，再清空奶瓶加熱器。

(

圖

12)

3

清空奶瓶加熱器並將內部徹底沖洗乾淨。如果沖洗後仍有水垢

痕跡，請重複除垢程序。

(

圖

13)

回收

本產品使用壽命結束時，請勿與一般家庭廢棄物一併丟棄。請將

該產品送至政府指定的回收點或進行回收。

此舉能為環保盡一份

心力。

請遵循您所在國家

/

地區對電氣與電子產品分類收集的規定。正確

處理廢棄產品有助於避免對環境和人類健康帶來負面影響。

單元

Unit

鉛

(Pb)

Lead

汞

(Hg)

Mercury Cadmium

Hexavalent

chromium

Polybrominated

biphenyls

Polybrominated

diphenyl ethers

鎘

(Cd)

六價鉻

(Cr

+6

)

多溴聯苯

(PBB)

多溴二苯醚

(PBDE)

限用物質及其化學符號

Restricted substances and its chemical symbols

電源線組

塑膠外殼

開關

溫控器組件

○

- ○

○ ○

○

○○

○

設備名稱：飛利浦AVENT 三合一食品加熱器，型號（型式）：

SCF355

Equipment name Type designation (Type)

備考1：“超出0.1 wt %”及“超出0.01 wt % ”係指限用物質之百分比含量超出百分比

含量基準值。

備考

2：“○”係指該項限用物質之百分比含量未超出百分比含量基準值。

備考

3：“－”係指該項限用物質為排除項目。

Note 1 : “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the

restricted substance exceeds the reference percentage value of presence condition.

Note 2 : “○” indicates that the percentage content of the restricted substance does not exceed the

percentage of reference value of presence.

Note 3 : The “－” indicates that the restricted substance corresponds to the exemption.

○

繁體中文52

保固與支援

如果您需要資訊或支援，請造訪：

www.philips.com/support

，

或另行參閱全球保證書。

Page is loading ...

Avent SCF355/00 User manual

This manual is also suitable for

Avent SCF355/00 User manual

in other languages

Related papers

Other documents