Signia miniPocket User guide

miniPocket

User Guide

2

Content

Your remote control 4

Components 5

Key lock 6

Pairing hearing inruments 7

Function overview 11

Further information 13

Cleaning 13

Replacing the battery 14

Troubleshooting 17

3

Service 19

Adjuing the signal rength 20

Important safety information 22

Personal safety 22

Product safety 24

Important information 27

Intended use 27

Symbols 28

Operating, transport and orage conditions 30

Disposal information 31

Conformance information 33

Country-specic information 34

4

Your remote control

miniPocket is a remote control for hearing inruments. It

works with our specic hearing inruments. Your Hearing

Care Professional will advise you on the compatible models.

CAUTION

Read this user guide thoroughly and completely and

follow the safety information in this document to avoid

damage or injury.

5

Components

➊ Status LED

➋ Volume buttons

➌ Keyring

➍ Key lock switch

➎ Program change button

➏ Battery door remover tool

➏

6

Key lock

XTo prevent any accidental

operation while the remote

control is in a pocket or bag,

move the key lock switch to

the lock position (red colour visible).

When the key lock is active, all buttons on the remote control

are disabled.

7

Pairing hearing inruments

Your hearing inruments need to be paired with your

remote control. After that, the pairing is saved in the hearing

inruments and remembered each time they are turned on.

XLock the remote control (red colour visible).

XFir turn the hearing inruments o:

Open the battery compartments. If your hearing

inruments do not have a battery compartment, turn them

o as described in the hearing inruments' user guide.

XThen turn the hearing inruments on:

Close the battery compartments. If your hearing

8

inruments do not have a battery compartment, turn them

on as described in the hearing inruments' user guide.

The hearing inruments are now in pairing mode. You have

3 minutes to complete the pairing. Follow the eps below.

XInsert the hearing inruments into your ears.

XHold down the button on the remote control while

switching the key lock to the unlock position (green colour

visible).

XRelease the button.

The remote control is now in setup mode, the LED will be

on.

9

While the remote control is in setup mode, do not press

or . This would change other settings.

XHold down the button until the pairing conrmation

sound is played in the hearing inruments. It takes

approximately 2 seconds for the sound to art playing.

XEnsure that the conrmation sound is heard in both

hearing inruments. When heard, the pairing will be

complete.

10

The remote control will remain in setup mode for an

additional 30 seconds. The conrmation sound can be

played again by pressing during these 30 seconds.

XTo exit the setup mode of the remote control, wait 30

seconds or move the key lock switch to the lock position

(red colour visible).

When pairing is nished, the remote control is ready for use.

XEnsure that it is unlocked (green colour visible).

If the hearing inruments could not be paired, refer to

"Troubleshooting" section.

11

Function overview

Function Description

Volume or

Press once to adju the volume one level

at a time. Or, press and hold until desired

volume is reached.

Hearing

program

short press

➧ Switches to the next hearing program.

Turn on/o

(andby)

and long press (2 seconds)

➧ Turns your hearing inruments on or o.

12

Function Description

Reset long press (2 seconds)

➧ Switches to hearing program 1 and sets the

default volume level.

13

Further information

Cleaning

NOTICE

XDo not put your remote control in water!

XDo not clean your remote control with

alcohol or benzine.

XClean the remote control as necessary with a dry or

slightly damp soft cloth.

Use only diilled water to dampen the cloth.

XAvoid any cleaning agents.

14

Replacing the battery

The remote control uses a CR 2450 button cell battery.

XAim the point of the

tool to the keyhole

above the battery

compartment cover ➊.

XPress the tool vertically

into the hole and at the

same time slide the

battery compartment

cover in the direction of

the arrow ➋.

XRemove the empty

battery by pulling the

removal ap ➌.

Note: Please use the

provided tool to open the

battery compartment cover.

Any self‑made tool like

paper clips might damage

the child lock feature.

15

Insert the battery with the '+' symbol facing up:

XSlide it under the holder, then push it

down.

16

XAttach the cover by sliding it onto the remote control.

XTo Close; slide the battery compartment cover in and a

'click' sound will be heard when the child lock is properly

engaged. ➌

17

The pairing atus is remembered by the remote control

when replacing the battery. There is no need to pair the

hearing inruments again after battery replacement.

Troubleshooting

If the device does not work:

● Ensure that the battery is inserted correctly. Refer to

section "Replacing the battery".

● Ensure that the keys are not locked. Refer to section

"Key lock".

● Ensure that there is nothing between the hearing

inruments and the remote control.

18

● Increase the signal rength. Refer to section

"Adjuing the signal rength".

● Pair the hearing inruments again. Refer to section

"Pairing hearing inruments".

● Ask your Hearing Care Professional if this remote control

is compatible with your hearing inruments.

If the hearing inruments cannot be paired:

● Increase the signal rength. Refer to section

"Adjuing the signal rength".

● Pair the hearing inruments again. Refer to section

"Pairing hearing inruments".

19

If the LED is no longer activating:

● Ensure that the keys are not locked. Refer to section

"Key lock".

● The battery may be low. Replace the empty battery.

Consult your Hearing Care Professional if you encounter

further problems.

Service

If you have technical problems with the device, consult your

Hearing Care Professional for service purposes. Do not

service or maintain the device while in use.

20

Adjuing the signal rength

The remote control works by emitting a high‑frequency audio

signal. This signal may be heard by those under 30 years old.

Two signal rength levels of the control signal are available.

By default, the remote control uses the ronge setting to

ensure a reliable connection with your hearing inruments.

A lower signal rength can be chosen if the control signal

diurbs others. Be aware that this can aect the reliability of

the connection.

To adju the signal rength:

XLock the remote control (red colour visible).

XHold down the button on the remote control while

switching the key lock to the unlock position (green colour

visible).

Page is loading ...

Signia miniPocket User guide

Signia miniPocket User guide

Related papers

Other documents