Intermec Trakker Antares 2485 User manual

Trakker Antares 2485
Intermec
Brand
Intermec
Model
Trakker Antares 2485
Type
User manual

This manual is also suitable for

TRAKKER
Antares
248X Badge Scanner Instruction Sheet
The badge scanner on your TRAKKER
Antares
2480, 2481, 2485, or 2486 terminal allows
you to easily scan bar codes from badges or other cards. This instruction sheet explains
how to install the badge scanner.
Caution
Inte
g
rated circuits on
p
rinted circuit boards (PCB) in this e
q
ui
p
ment are sensitive to
dama
g
e b
y
electrostatic dischar
g
e (ESD). Prevent ESD b
y
alwa
y
s wearin
g
skin
contact
g
round stra
p
s
f
irml
y
attached to the e
q
ui
p
ment metal base assembl
y
when
workin
g
inside o
f
the e
q
ui
p
ment housin
g
. Failure to com
p
l
y
ma
y
result in dama
g
e to
PCB com
p
onents.
Conseil
Les circuits intégrés des cartes de circuit imprimé (PCB) de cet équipement sont sensibles à
l'endommagement dû à la décharge électrostatique (ESD). Évitez la décharge
électrostatique en mettant toujours contre la peau des courroies neutralisantes attachées
fermement à l'assemblage de la base en métale de l'équipement lorsque vous travaillez à
l'intérieur du boîtier de l'équipement, faute de quoi vous risquez d'endommager les pièces
des PCB.
To install the badge scanner
1. Turn off your terminal and unplug the power supply.
2. If you have a wall- or desk-mounted terminal, remove the mounting bracket from the
terminal. For help, see the instruction sheet that came with the bracket.
3. Using a Phillips screwdriver, take out the two mounting screws and the badge scanner
placeholder. Save and reuse the mounting screws to attach the badge scanner.
4. Insert the badge scanner into the badge scanner well.
248XBRI.002
Badge
scanner
Badge
scanner
well
Badge
scanner
cable
Mounting screw
(2 places)
5. Insert and tighten the two mounting screws to secure the badge scanner to the
terminal.
6. Take out the six screws and remove the terminal’s back panel. Save and reuse the
screws to replace the back panel.
Badge
scanner
Badge
scanner
cable
Badge
scanner
connector
Scissors
seal
Cable
restraint
248XBRI.006
7. Keeping the scanner cable snug against the bottom edge of the rear enclosure, gently
pull up on the scissors seal, pass the cable through the seal and under the cable
restraint bar, and close the seal.
8. Loosen the screw on the cable restraint and pass the scanner cable under the cable
restraint. Tighten the screw to secure the cable.
9. Plug the badge scanner cable into the badge scanner connector.
10. Replace the terminal’s back panel and remount the terminal on the desk or wall.
11. Plug in the power supply and turn on the terminal.
6001 36th Avenue West
P.O. Box 4280
Everett, WA 98203-9280
© 1998 Intermec Corporation
All Rights Reserved
P/N
066993-001
  • Page 1 1
  • Page 2 2

Intermec Trakker Antares 2485 User manual

Trakker Antares 2485
Intermec
Brand
Intermec
Model
Trakker Antares 2485
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents