Stairmaster 10G 9-5285 Operating instructions

Brand: Stairmaster

Model: 10G 9-5285

Type: Operating instructions

Install Instructions

Page 1

620-8684 Rev. D

Applies to: All 8/10-Series Cardio with 15/19” STB-Ready Console

Tools Required:

• #2 Phillips Screwdriver

Parts Required:

• 700-0474 “KIT, BROADCAST VISION, IR TO STB”

If NOT using a set top box (STB) manufactured by LG or Amino, the cable adapter box

(CAB) part number 700-0425 will need to be installed between the RJ45 cable from

the machine and the 3.5mm-to-RJ45 adapter - please refer to CAB install document

620-8504 for more information.

If using coaxial cable between the console and the STB, go to Page 14.

1. Using a #2 phillips screwdriver, remove the electrical plate at the front of the unit then disconnect any cable

inlets securing internal cables to the electrical plate .

NOTE: Please note that the instructions given on Pages 1-4 are valid for most units, a Recumbent Bike is only

shown as an example. For STB Kit install on all other units, please see below:

• 8RDE Rear Drive Elliptical (Pg. 5)

• 8TR(x) Treadmills (Pg. 8)

• 8FC FreeClimber (Pg. 10)

• 10TRx FreeRunner (Pg. 12)

STB Kit Install Instructions for 2019 Capacitive Touch Embedded

Console

Install Instructions

Page 2

620-8684 Rev. D

2. Route HDMI cable down through mast of machine and out of the front of the electrical plate. The routing

path is represented by the dark bold line below. Be sure to used the included zip ties to secure the HDMI

cable to the other cables inside the unit as it is routed down through the machine.

9-6140-XXXXXX (8CT)

9-5250-XXXXXX (8G)

9-6140-XXXXXX (8UB)

9-6140-XXXXXX (8RB)

9-6150-XXXXXX (8VS)

9-5260-XXXXXX (8FC)

Install Instructions

Page 3

620-8684 Rev. D

3. After routing the HDMI cable, pass the HDMI cable and the RJ45 cable through the opening in the electrical

plate, then use a #2 phillips screwdriver to secure the electrical plate to the frame using two (2) of the sup-

plied screws. Use the cable retention clamps as shown to secure any loose wires.

4. Connect the RJ45 and HDMI cables running up to the 15” Embedded console to their respective connections.

Connect the RJ45 cable (image left) to the cable labeled “STB IR” and the HDMI cable to the console (image

right).

Install Instructions

Page 4

620-8684 Rev. D

5. Plug the RJ45 cable running from inside the unit into the 3.5mm-to-RJ45 adapter, then plug the IR Emitter

into the adapter.

RJ45 CABLE

FROM UNIT

TO CONTINUE INSTALLATION, PLEASE TURN TO PAGE 15

See note on page 1 to determine if you need

additional parts to control the set top box.

Install Instructions

Page 5

620-8684 Rev. D

For 8RDE Rear Drive Elliptical(9-6150):

Tools Required:

• #2 Phillips Screwdriver

1. Using a phillips screwdriver, remove the electrical plate at the front of the unit then disconnect any cable

inlets securing internal cables to the electrical plate.

2. Route HDMI cable down through mast of machine and out of the front of the electrical plate. The routing

path is represented by the dark bold line below. Be sure to used the included zip ties to secure the HDMI

cable to the other cables inside the unit as it is routed down through the machine.

Install Instructions

Page 6

620-8684 Rev. D

3. After routing the HDMI cable, pass the HDMI cable and the RJ45 cable through the opening in the electrical

plate, then use a #2 phillips screwdriver to secure the electrical plate to the frame using four (4) of the sup-

plied screws. Use the cable retention clamps as shown to secure any loose wires.

4. Connect the RJ45 and HDMI cables running up to the 15” Embedded console to their respective connections.

Connect the RJ45 cable (image left) to the cable labeled “STB IR” and the HDMI cable to the console (image

right).

Install Instructions

Page 7

620-8684 Rev. D

5. Plug the RJ45 cable running from inside the unit into the 3.5mm-to-RJ45 adapter, then plug the IR Emitter

into the adapter.

RJ45 CABLE

FROM UNIT

TO CONTINUE INSTALLATION, PLEASE TURN TO PAGE 15

See note on page 1 to determine if you need

additional parts to control the set top box.

Install Instructions

Page 8

620-8684 Rev. D

For 8TR(x) Treadmills (9-9201 + 9-9202 + 9-9204 + 9-9191 + 9-9192 +9-9194):

Tools Required:

• #2 Phillips Screwdriver

1. Route HDMI cable down through mast of machine and out through the hole in the frame. The routing path is

represented by the dark bold line below. Be sure to used the included zip ties to secure the HDMI cable to the

other cables inside the unit as it is routed down through the machine.

2. Route the end of the HDMI cable out of the bottom of the treadmill frame where shown below. Use the cable

retention clamps to secure any loose wires.

Install Instructions

Page 9

620-8684 Rev. D

3. Connect the RJ45 and HDMI cables running up to the 15” Embedded console to their respective connections.

Connect the RJ45 cable (image left) to the cable labeled “STB IR” and the HDMI cable to the console (image

right).

4. Plug the RJ45 cable running from inside the unit into the 3.5mm-to-RJ45 adapter, then plug the IR Emitter

into the adapter.

RJ45 CABLE

FROM UNIT

TO CONTINUE INSTALLATION, PLEASE TURN TO PAGE 15

See note on page 1 to determine if you need

additional parts to control the set top box.

Install Instructions

Page 10

620-8684 Rev. D

For 8FC FreeClimber (9-5260):

Tools Required:

• #2 Phillips Screwdriver

1. Route HDMI cable down through mast of machine and out through the hole in the frame (please note that

the user right side shroud has been removed for clarity. The routing path is represented by the dark bold line

below. Be sure to used the included zip ties to secure the HDMI cable to the other cables inside the unit as it is

routed down through the machine.

2. Route the end of the HDMI cable out of the bottom of the FreeClimber frame where shown below. Use the

cable retention clamps to secure any loose wires.

Install Instructions

Page 11

620-8684 Rev. D

3. Connect the RJ45 and HDMI cables running up to the 15” Embedded console to their respective connections.

Connect the RJ45 cable (image left) to the cable labeled “STB IR” and the HDMI cable to the console (image

right).

4. Plug the RJ45 cable running from inside the unit into the 3.5mm-to-RJ45 adapter, then plug the IR Emitter

into the adapter.

RJ45 CABLE

FROM UNIT

TO CONTINUE INSTALLATION, PLEASE TURN TO PAGE 15

See note on page 1 to determine if you need

additional parts to control the set top box.

Install Instructions

Page 12

620-8684 Rev. D

For 10TRx FreeRunner (9-9701 + 9-9704):

Tools Required:

• #2 Phillips Screwdriver

1. Route HDMI cable down through mast of machine and out through the hole in the frame. The routing path is

represented by the dark bold line below. Be sure to used the included zip ties to secure the HDMI cable to the

other cables inside the unit as it is routed down through the machine.

2. Route the end of the HDMI cable out of the bottom of the treadmill frame where shown below. Use the cable

retention clamps to secure any loose wires.

Install Instructions

Page 13

620-8684 Rev. D

3. Connect the RJ45 and HDMI cables running up to the 15” Embedded console to their respective connections.

Connect the RJ45 cable labeled “A” (image left) to the cable labeled “STB IR” and the HDMI cable to the con-

sole (image right).

4. Plug an RJ45 cable into the “A” port on the front of the treadmill (image left)

5. Plug the other end of the RJ45 cable into the 3.5mm-to-RJ45 adapter then plug the IR Emitter into the

3.5mm-to-RJ45 adapter (image right)..

PORT A

PORT B

RJ45 CABLE

TO PORT A

3.5mm-TO-RJ45

ADAPTER

IR EMITTER

See note on page 1 to determine if you need additional parts to control the set top box.

TO CONTINUE INSTALLATION, PLEASE TURN TO PAGE 15

Install Instructions

Page 14

620-8684 Rev. D

For using coaxial cable connection between the console and STB

1. Connect the coaxial cable to the coaxial connection on the front of the machine.

NOTE: For treadmills, the coaxial cable will need to be routed out of the bottom of the treadmill.

2. Ensure that the coaxial cable from the mast of the machine is connected to the console (image left).

3. Connect the RJ45 cable from the mast to the console cable labeled “STB IR” (image right). For 10TRx, this cable

is labeled “A”.

4. Plug an RJ45 cable into the CAT6 port on the front of the unit. For the 10TRx plug an RJ45 cable into “Port A”

(image left).

5. Plug the other end of the RJ45 cable into the 3.5mm-to-RJ45 adapter then plug the IR Emitter into the

3.5mm-to-RJ45 adapter.

PORT A

PORT B

RJ45 CABLE

TO PORT A

3.5mm-TO-RJ45

ADAPTER

IR EMITTER

See note on page 1 to determine if you need additional parts to control the set top box.

TO CONTINUE INSTALLATION, PLEASE TURN TO PAGE 15

Install Instructions

Page 15

620-8684 Rev. D

Mounting the IR Emitter:

Once the 3.5mm end of the IR emitter cable, has been connected to the RJ45-to-3.5mm adapter,

the IR diode end of the IR emitter cable will need to be attached to the front of the set top box

(STB) where the IR receiver is located. If you cannot locate the IR receiver on the STB, shining a

ashlight at the front of the STB can help in locating it.

In the examples above, you can see the IR emitter mounted to the STB over the STB’s IR receiver.

The two examples on the left show common locations of the IR receiver on two STBs.

Once the IR diode is in place, install the IR shield onto the front of the IR diode. This will ensure

that the signal sent to the STB will only change the settings on the STB that the IR diode has been

applied to.

TO CONTINUE INSTALLATION, PLEASE TURN TO PAGE 16

Install Instructions

Page 16

620-8684 Rev. D

Programing the IR Emitter + Selecting Video Source:

1. Enter the service menu by tapping the upper left

corner of the screen, then the upper right corner

of the screen, then the upper left corner of the

screen again.

2. Enter code “218” then press enter to access the

service menu.

3. Tap on “Tuner” to enter the Tuner sub-menu.

4. Tap on “STB” to enter the Set Top Box sub-menu.

5. Use the drop down menu to select the manufac-

turer of the set top box (STB).

NOTE: If your STB manufacturer is not listed on the

drop down menu, you must select “CAB” from the

menu and use the CAB add-on controller (Part #: 700-

0425). Follow instructions in the CAB box to set up

the device.

Install Instructions

Page 17

620-8684 Rev. D

6. Select the “Mode” and tap on either “HDMI” (if

using HDMI) or “Tuner” (if using coaxial).

NOTE: If no channels are present when using coaxial

connection (Tuner), perform a channel scan in the

Calibration and Setup menu.

Stairmaster 10G 9-5285 Operating instructions

Stairmaster 10G 9-5285 Operating instructions

Stairmaster 10G 9-5285 Operating instructions

Related papers

Other documents