Chore-Time MV2406R 57-Inch ENDURA® Fan Installation & Operator's Instruction Manual

Brand: Chore-Time

Model: MV2406R 57-Inch ENDURA® Fan

Type: Installation & Operator's Instruction Manual

This manual is also suitable for

Endura 57" Fan

Thank You The employees of CTB Inc. would like to thank you for your recent Chore-Time

purchase. If a problem should arise, your Chore-Time distributor can supply the necessary information

to help you.

57" Endura

Fan

Installation & Operator’s

Instruction Manual

Fan Part Numbers and Specifications

Operating static pressure should be less than 0.15 inches water column [37.5 Pa].

The Fan Inlet and exhaust must be kept clear of obstructions. Failure to keep the Fan

airflow path clear of obstructions could cause loss of Fan performance and Fan damage.

MV2406RNovember 2019

Static Pressure at

.10" w.c.

[25 Pa]

Static Pressure

at .15" w.c.

[37.5 Pa]

Fan Part No. Bess Lab

Test No.

Voltage Phase Hz Nominal

RPM

Amps Starting

Amps

CFM

[cmh]

CFM/W

[cmh/W]

CFM

[cmh]

CFM/W

[cmh/W]

53464-21

53464-21S

12615 230 1 60 542 6.9 36.0 30400

[51600]

20.4

[34.7]

28400

[48200]

18.1

[30.7]

53464-22

53464-22S

12614 230 1 60 543 5.4 27.5 27100

[46100]

[39.1]

25100

[42700]

20.1

[34.2]

53464-23 17224 230 1 60 538 4.0 27.5 21200

[36000]

24.6

[41.7]

18900

[32200]

20.8

[35.3]

53464-41

53464-41S

12616 230 3 60 534 4.8 40.0 30000

[51100]

20.9

[35.6]

27800

[47200]

18.1

[30.8]

53464-42

53464-42S

12619 230 3 60 539 4.1 40.0 26900

[45600]

23.3

[39.6]

24800

[42200]

20.4

[34.6]

53464-51

53464-51S

12617 230 3 50 527 5.2 45.0 29500

[50100]

20.8

[35.3]

27200

[46200]

18.1

[30.8]

53464-52

53464-52S

12618 230 3 50 534 4.7 45.0 26500

[45100]

22.9

[38.9]

24500

[41600]

20.1

[34.1]

Safety Information 57" Endura

Fan

MV2406R

Carefully read all safety messages in this manual and on your equipment safety signs. Follow recommended precautions

and safe operating practices. Keep safety signs in good condition. Replace missing or damaged safety signs.

DANGER: Electrical Hazard

Disconnect electrical power before inspecting or servicing equipment. Ground all electrical

equipment for safety. All electrical wiring must be done by a qualified electrician in

accordance with local and national electric codes. Ground all non-current carrying metal

parts to guard against electrical shock. With the exception of motor overload protection,

electrical disconnects and over current protection are not supplied with the equipment.

DANGER: Rotating Fan Blade

Keep Hands away. Disconnect power before servicing. Fan may start automatically.

Do not operate the Fan without the screens in place. Disregard to these things will

cause serious injury including death.

LIMITED WARRANTY

Chore-Time Group, a division of CTB, Inc. (“Chore-Time”) warrants new CHORE-TIME Endura

Fans manufactured by Chore-Time

to be free from defects in material or workmanship under normal usage and conditions, for One (1) year from the date of installation by

the original purchaser (“Warranty”). Chore-Time provides for an extension of the aforementioned Warranty period (“Extended

Warranty Period”) with respect to certain Product parts (“Component Part”) as set forth in the table below. If such a defect is

determined by Chore-Time to exist within the applicable period, Chore-Time will, at its option, (a) repair the Product or Component

Part free of charge, F.O.B. the factory of manufacture or (b) replace the Product or Component Part free of charge, F.O.B. the factory of

manufacture. This Warranty is not transferable, and applies only to the original purchaser of the Product.

CONDITIONS AND LIMITATIONS

THIS WARRANTY CONSTITUTES CHORE-TIME’S ENTIRE AND SOLE WARRANTY AND CHORE-TIME EXPRESSLY

DISCLAIMS ANY AND ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, EXPRESS AND IMPLIED

WARRANTIES, INCLUDING, WITHOUT LIMITATION, WARRANTIES AS TO MERCHANTABILITY OR FITNESS FOR

PARTICULAR PURPOSES. CHORE-TIME shall not be liable for any direct, indirect, incidental, consequential or special damages

which any purchaser may suffer or claim to suffer as a result of any defect in the Product. Consequential or Special Damages as used

herein include, but are not limited to, lost or damaged products or goods, costs of transportation, lost sales, lost orders, lost income,

increased overhead, labor and incidental costs, and operational inefficiencies. Some jurisdictions prohibit limitations on implied

warranties and/or the exclusion or limitation of such damages, so these limitations and exclusions may not apply to you. This warranty

gives the original purchaser specific legal rights. You may also have other rights based upon your specific jurisdiction.

Compliance with federal, state and local rules which apply to the location, installation and use of the Product are the responsibility of

the original purchaser, and CHORE-TIME shall not be liable for any damages which may result from non-compliance with such rules.

The following circumstances shall render this Warranty void:

· Modifications made to the Product not specifically delineated in the Product manual.

· Product not installed and/or operated in accordance with the instructions published by the CHORE-TIME.

· All components of the Product are not original equipment supplied by CHORE-TIME.

· Product was not purchased from and/or installed by a CHORE-TIME authorized distributor or certified representative.

· Product experienced malfunction or failure resulting from misuse, abuse, mismanagement, negligence, alteration, accident, or

lack of proper maintenance, or from lightning strikes, electrical power surges or interruption of electricity.

· Product experienced corrosion, material deterioration and/or equipment malfunction caused by or consistent with the

application of chemicals, minerals, sediments or other foreign elements.

· Product was used for any purpose other than for the care of poultry and livestock.

The Warranty and Extended Warranty may only be modified in writing by an officer of CHORE-TIME. CHORE-TIME shall have no

obligation or responsibility for any representations or warranties made by or on behalf of any distributor, dealer, agent or certified

representative.

Safety Information

Warranty

Component Part Extended Warranty Period

Endura

Fan Housing and Cones (Including Composite Shrouds, Composite Doors and HDPE Cone Panels)

Five (5) Years

57" Endura

Fan Un-Assembled Parts Packages

MV2406R

Un-Assembled Parts Packages

Un-Assembled 57" Endura

Fan Component Part Numbers

Fan Part No. Drive Assembly Motor Hardware Pkg. Fan Blade

53464-21U 53753-1 50496 53788-21XX 53219

53464-21SU 53753-1S 50496 53788-21XXS 54529

53464-22U 53753-1 49903 53788-22XX 53532

53464-22SU 53753-1S 49903 53788-22XXS 54530

53464-41U 53753-1 48608 53788-41XX 53219

53464-41SU 53753-1S 48608 53788-41XXS 54529

53464-42U 53753-1 48608 53788-42XX 53532

53464-42SU 53753-1S 48608 53788-42XXS 54530

53464-51U 53753-2 48608 53788-51XX 53219

53464-51SU 53753-2S 48608 53788-51XXS 54529

53464-52U 53753-2 48608 53788-52XX 53532

53464-52SU 53753-2S 48608 53788-52XXS 54530

XX= Number of Fans that can be built with components in Package.

Fan Blade Package

(53219-XX, 53532-XX, 54529-XX, or 54530-XX)

(53843-XX)

Component Package

(53850-XX)

Shroud and Door Package

(See Table Below)

Motor Pallet

Grill: (53129)

Screen: (48794)

(53788-AAXX, or -AAXXS)

Hardware Package

Drive Assembly

1 or 2 Drives per Box:

(53753-1, -2, -1S, -2S)

Grill

Screen

Fan Blade Part No.

(on Blade Spider)

Assembled Fan Component Part Numbers 57" Endura

Fan

MV2406R

Assembled Fan Component Part Numbers

Assembled 57" Endura

Fan Component Part Numbers

Fan Assembly 53464-21 53464-21S 53464-22 53464-22S 53464-23 53464-41 53464-41S 53464-42 53464-42S 53464-51 53464-51S

Item Component Part Numbers

Fan Assembly 1 53464-21P 53464-21PS 53464-22P 53464-22PS 53464-23P 53464-41P 53464-41PS 53464-42P 53464-42PS 53464-51P 53464-51PS

Fan Grill 2 53219 53219 53219 53219 53219 53219 53219 53219 53219 53219 53219

57" Endura

Fan Hardware Needed Per Fan (Un-Assembled)

MV2406R

Hardware Needed Per Fan (Un-Assembled)

57" Endura

Fan Hardware Items Per Fan

Items are Bulk packed in 53788-AAXX, or 53788-AAXXS (See previous page).

Item Qty. Description Part No.

1 1 Bottom Pivot Plate 53036

2 1 Top Pivot Plate 53037

3 4 Door Hinge Pin 53038

4 1 1/4 x 1-1-8" Sq. Key (For Blade) 2419-2

5 40 5/16-18 x 1 SS Hx Hd Shoulder Bolt 54287

6 55 5/16-18 Hx. Serrated SS Flange Nut 46764

7 2 .38 SS Flat Washer ST99070

8 1 72.5" Fan Cone Cable 53399

9 1 5/16-18 x 3" Eye Bolt 30663

10 2 Ø1/2" x 11" Door Spring 49629

11 24 1/4-10 x 1-1/2" Lag Screw SS 41561

12 7 Open Eye Hook 1214

13 1 Screen Spring (4 pc. per package) 54480-4

14 6 Orifice Frame Bracket 53611

15 2 Cable Clamp 732

16 1 Fan Description Decal 39002-XXX

17 1 Anti-Seize Lubricant 56262

18 --

57" Endura

Fan Instruction Manual

MV2406

Tools Needed and Supplies 57" Endura

Fan

MV2406R

Tools Needed and Supplies

3/8" socket, 1/2"socket or wrench, Side cutters, 1/4" nut driver, Motor power cord, Wire nuts / terminals, Optional

screw hook installation tool (CTB part number 13150-1), Caulking, 5/32" allen wrench (un-assembled)

New Installation Planning

Planning the layout of the spacing between Fans is very important. Spacing too close together will cause interference

between the discharge Cones.

5" [12.7cm]

!Important: Provide Shelter over Cones in areas where

snow or ice could cause damage. CTB Inc. Warranty Does

Not cover damage from external sources.

1-3/4" [4.4cm] required at

the bottom of the opening.

Important!

Fan

mounting

surface must be flat.

60-1/16" [152.5cm]

Minimum Spacing if

sides of Cone are flat-

tened (See page 17).

72" [182.9cm]

Recommended Spacing

13-11/16" [34.8cm] Inside Wall to Screen

Minimum Wall Thickness 3-1/2" [8.9cm]

42-13/16"

[108.7cm]

56-5/16" [143cm]

Square

70-1/8" [178.1cm]

60-1/8" [152.7cm]

4-5/16"

[10.9cm]

5-11/16" [14.4cm]

57-1/16" [

144.9cm] Max.

55-5/8" [

141.3cm] Min.

60-1/4" [

153cm]

60-1/4" [153.0cm]

57-3/8" [145.7cm] Max.

55-1/4" [140.3cm] Min.

57" Endura

Fan Installation

MV2406R

Inspecting the Shroud (For assembled versions skip to page 12)

Inspect the Shroud assembly for hardware as received.

Fan Shroud Assembly (Unassembled version)

Rest Fan Shroud on Saw Horses for ease of Assembly

Installation

(53626) Center V-Post

(48427) Magnet

(53026) Magnet Side Plate

Third Hole designates the

Top of Shroud.

Danger Decal is located in Bottom

Right corner of the Shroud.

Exhaust Side Down

Top of Fan Shroud

Installation 57" Endura

Fan

MV2406R

Attaching Fan Posts

(46764) x3

Nut

(53204)

Fan Post

Decal

(46764) x3

Nut

(27868-1) x3

Bolt

(53039)

Cone Bracket

(53206) Bottom Corner

Support Bracket

One Notch

1st Hole

View from Front of Fan

(bottom left corner)

Hardware Full Scale

2nd Hole

Two Notches

(53205) Top Corner

Support Bracket

(53039)

Cone Bracket

(53204)

Fan Post

(27868-1) x3

Bolt

(54287) 5/16-18 x 1.00

SS Shldr. Bolt

(46764) 5/16 Flg. Nut

57" Endura

Fan Installation

MV2406R

Cone Brackets, Corner Brackets (Corners without Posts)

(46764) Nut

(53205)Top

Corner Sup-

port Bracket

(27868-1)

Bolt

(53039)

Cone Bracket

Two Notches

1st Hole

2nd Hole

One Notch

(53039)

Cone Bracket

(27868-1) Bolt

(53206) Bottom

Corner Support

Bracket

(46764)

Nut

(54287) 5/16-18 x 1.00

SS Shldr. Bolt

(46764) 5/16 Flg. Nut

Hardware Full Scale

Installation 57" Endura

Fan

MV2406R

Installing the Drive Assembly and Motor Mount

Apply a Fan Description Decal to the Shroud

as shown

. (Included in Parts Package)

(53753-X)

(46764)

Drive Assembly

(46764)

(48396C) Motor Support

(54287) x8

(54287) 5/16-18 x 1.00

SS Shldr. Bolt

(46764) 5/16 Flg. Nut

Hardware Full Scale

Use the Bottom Set of Holes in the

Posts as shown.

57" Endura

Fan Installation

MV2406R

Top and Bottom Pivot Plates and Eyebolt, Door Stop Cable

(53037)

Top Pivot Plate

(46764) Nut

(3066) Eyebolt

(53036) Bottom Pivot Plate

(46764) Nut

(46764)

Nut

Insert (53399) Door Stop Cable

Assembly into Top Pivot Plate

(46764) 5/16 Flg. Nut

Hardware Full Scale

Pivot Plate Tab

Centered in V-Post

V-Post

Pivot Plate Tab

Centered in V-Post

V-Post

Installation 57" Endura

Fan

MV2406R

Bottom Shelf Installation

Attaching the Fan to the Wall

SS 1/4-10 x 1-1/2" Lag Screws

Tighten until Snug only. Do not

Deform the Bottom Shelf.)

(41561)

(41561) 1/4 x 1-1/2 Lag Screw

Center of Rough

Opening

Outside of House

(53338)

Bottom

Shelf

Center of Bottom

Shelf

If the Shelf is too long Trim

equal amounts from both ends.

This Flange must not be

bowed after installation!

Eyebolt indicates the Top of

the Fan.

Line up the four Holes in the

Shroud with the Holes in the

Bottom Shelf.

Set Fan Shroud on the

Bottom Shelf.

57" Endura

Fan Installation

MV2406R

It is important when attaching the Fan to the Wall to keep edges of Shroud straight.

(41561)

Pre-drill holes to 3/16" [4.8 mm] to

avoid splitting lumber. If holes do not

line up with the lumber it may be nec-

essary to put Screws through Shroud.

Important! Attach the Fan to the

Wall with 1/4 x 1-1/2" Lag Screws

(41561) in the specific order shown.

Attach with a total of 20 Lag Screws.

A 600 Lb. Hand Clamp can be used

to straighten Shroud if necessary.

Keep edges of Shroud Straight

Use the Hole in the Corner Bracket that is

centered with Lumber to avoid splitting.

(41561) 1/4 x 1-1/2 Lag Screw

Installation 57" Endura

Fan

MV2406R

Cone Assembly

Assemble Cone Panels as shown below.

Two Holes

Prop the Cone

Panels up off

the ground to

ease assembly

One Hole

Tabs Up

Tabs Snap positively

in place

57" Endura

Fan Installation

MV2406R

Installing the Orifice Frame

Cone Installation

(46764)

(54287)

Rounded Tab on the Cone

Orifice Frame Shown Gray for Clarity.

Important! Line up the Seam in the Orifice Frame

with one of the rounded Tabs on the Cone.

(53416)

Orifice

Frame

(53611)

Frame

Bracket

(54287) 5/16-18 x 1.00

SS Shldr. Bolt

(46764) 5/16 Flg. Nut

Hang the Cone on the Eye-Bolt extruding from the top of the Shroud using the hole in

the Cone as shown.

(30663) Eyebolt

Seam in Orifice Frame

Installation 57" Endura

Fan

MV2406R

Attach the cone to the Shroud as shown below.

Use the Bolts in the Cone to attach the Cone to

the Cone Brackets. Use the Bottom set of holes

in the Cone Brackets.

If necessary, slip a thin piece of metal between

the Shroud and Cone and work it around the

Cone to get it on.

Slip the Orifice Frame behind the Bottom Pivot Plate.

Bottom Pivot

Plate

5/16 Flg. Nut (46764)

5/16 Flg. Nut (46764) (46764) 5/16 Flg. Nut

57" Endura

Fan Installation

MV2406R

Door Assembly and Installation

Insert Door Pins in both Doors as shown.

Push Pins in until they bottom out.

Doors are Left and Right specific.

Insert Door Pins into Bottom

Pivot Plate.

Grab the Door in the Center, Bow the Door outward,

and insert the Top Door Pin into the Top Pivot Bracket

as shown. Do not Overbow the Doors!

(53038) Door Pin

Door

Top Pivot Plate

Bottom Pivot Plate

Door Pin

Spring

Holes in

Doors

View of Back of Door View of Back of Door

(53038) Door Pin

Installation 57" Endura

Fan

MV2406R

Grill Installation

Install the Fan Cone Grill (as shown). Attach the end of the Door Stop Cable to the bot-

tom Grill Leg as shown.

(54287)

(46764)

If it is desired to Mount Fans at the minimum spacing cutting the Grills is required as

shown.

(46764)

(ST99070)

(46764)

(54287)

Door Stop

Cable

Door Stop Cable

even with the

edge of Cone

(ST99070)|

3/8 SS Flat Washer

(46764)

5/16 Flg. Nut

(54287)

5/16-18 x 1.00 Bolt

Cut the Grill here

Push the Cone Side

in and use a Clamp to

secure the Grill

Wires.

(732) Clamp (In Parts Package)

57" Endura

Fan Installation

MV2406R

Rotate Motor Support (Assembled Fans)

Rotate the Motor Support Bracket into the upright position by removing the

upper Bolt and Nut, and loosening the lower Bolt and Nut.

Attach the Motor Support Bracket to the Posts with

5/16 Bolts (54287) and 5/16 Flange Nuts (46764).

Remove Bolt

4x (54287) 5/16-18 x 1.00

SS Shldr. Bolt

4x (46764) 5/16 Flg. Nut

Loosen Bolt

(46764)

5/16 Flg. Nut

(54287)

5/16-18 x 1.00 SS Shldr. Bolt

Installation 57" Endura

Fan

MV2406R

Motor Installation

Attach Motor to Z-Bracket.

Motor

(54287)

Torque Set Screw to 150-165 IN-LBS

[16.9-18.6 NM]

Motor

Anti-Seize

Motor

Sheave

3/16" Key Supplied (Taped to Motor)

Center the Sheave with the

Hole in the Z-Bracket

(54287) 5/16-18 x 1.00 SS

Shldr. Bolt

(46764)

5/16 Flg. Nut

Z-Bracket

(46764)

Page is loading ...

Chore-Time MV2406R 57-Inch ENDURA® Fan Installation & Operator's Instruction Manual

Brand: Chore-Time

Model: MV2406R 57-Inch ENDURA® Fan

Type: Installation & Operator's Instruction Manual

This manual is also suitable for

Endura 57" Fan

Download PDF

report

Chore-Time MV2406R 57-Inch ENDURA® Fan Installation & Operator's Instruction Manual

This manual is also suitable for

Chore-Time MV2406R 57-Inch ENDURA® Fan Installation & Operator's Instruction Manual

Related papers

Other documents