CC 200 Cable Retractor Adapter Kit
Planning
Before installing the adapter, be certain there is
adequate space under the table for the retractable system with the
attached bracket.
Determine the retractor mounting orientation: horizontal or vertical.
If only one retractor is mounted, use a filler module, part #70-678-08
in place of the second retractor.
If mounting horizontally, the horizontal
bracket kit, part #70-678-00, is required.
68-1894-50
Rev. B
06 11
The CC 200 Bracket Kit, part #70-678-10, allows one
or two Cable Retractors to be installed in the
Cable Cubby
®
200 enclosure. The bracket kit
adapts the AAP opening of the enclosure to
allow the installation of a Cable Retraction
System for Cable Cubby Enclosures.
CC 200 Cable
Retractor Bracket Kit
(x4)
CC 200
Bracket
Horizontal Mounting Clearance
9.0" (228.6 mm)
3.0"
(76.2 mm)
13.6" (345.4 mm)
CC 200
Bracket
Vertical Mounting Clearance
3.0"
(76.2 mm)
23.3" (591.8 mm)
0.33" (8.4 mm)
NOTE: To prevent objects from impeding
cable retraction, ensure at least
3 inches of clearance from the
exposed cable side of the enclosure.
Bracket and Retractor Mounting
WARNING: Disconnect power from the Cable Cubby 200
power module before beginning installation.
1. Using the mounting bolt supplied with the CC 200 kit
(1/4-20 x 3 in), mount the CC 200 bracket to the retractor as
shown on the right. Do not overtighten the bolt.
Once the retractor is mounted to the bracket, the assembly can
be installed into the enclosure.
2. The cable stops and connecters may be too large to fit through
the AAP opening at the same time as the retractor. Pull a short
amount of cable out of the retractor and push it through the
AAP opening before installing the retractor/bracket assembly.
3. Press the bracket and retractor assembly against the bottom
of the enclosure, lining the bracket holes up with the AAP
mounting holes on the enclosure. Fasten from the top using
the supplied four screws.
4. Refer to the Cable Retraction System for Cable Cubby
Enclosures User Guide at www.extron.com for further
retractor mounting instructions.
Mounting Screw
w/Washer (4 plcs)
Mounting Bolt
and Nut
CC 200
Bracket
CC 200 Bracket and
Retractor Assembly
1
3
2
Extron USA - West
Headquarters
+800.633.9876
Inside USA and
Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA and
Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
© 2011 Extron Electronics All rights reserved. www.extron.com
-
1
-
2
Extron Cable Cubby 200 User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Extron Retractor User manual
-
-
-
Extron Hideaway HSA 402 User guide
-
Extron electronics Cable Cubby 500 User manual
-
-
-
-
-
Extron TLP Pro 725C User manual
