Golden Lighting 1048-3P GDW Operating instructions

Assembly Instructions: 1048-3P (Chatham)

IMPORTANT:

• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.

• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!

• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!

PREPARING FOR INSTALLATION

Remove all of the contents from the carton. See the important notes above. Shut off

thepoweratthecircuitbreakerandcompletelyremovetheoldxturefromtheceiling,

includingtheoldmountingstrap.

1.Fromthepartsbagremovethemountingstrapassembly.Oneendofnipple(F)should

beattachedtomountingstrap(A)withwasherandhexnut(CandD)inplace.Theother

endshouldhavecanopyloop(H)attached.Attachmountingstrap(A)tothejunctionbox

usingmountingscrews(B)andascrewdriver.Tightensecurely.

2. Unscrew canopy loop collar (I) from canopy loop (H). Pass canopy (G) over the mounted

canopylooptotesttheheight.Approximatelyhalfofthecanopyloop’sexteriorthreads

shouldbeexposed,andthecanopyloopcollarshouldtsnuglyontothecanopyloop.

Remove canopy (G) and adjust the height of nipple (F) and canopy loop (H) until the

desiredheightisreached.

CLEANING TIPS

Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the

xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.

For Customer Service, please contact

the place of purchase.

ASSEMBLING THE FIXTURE

3. Thread center rod (Q) onto post (S). Slide the top of center rod (Q) into the center of

xturebody(O).Threadwasher(P)andtoploop(L)ontopost(M)ofrod(Q).

4.Bymeasuring,determinethecorrectnumberofchainlinksneededforproperhanging

height.Ifnecessary,useapairofplierstoopenandremoveanyexcesschain.Attach

chain connectors (K) to each end of chain (J) before attaching one end of the chain

connector/chain to top loop (L). Close the chain connector. Connect the other chain

connector (K) to canopy loop (H).

5.Feedthexture’swiresupthroughtoploop(L)andthenthroughchain(J)(everythree

links or so). Slide canopy loop collar (I) and canopy (G) onto the chain/wire.

CONNECTING THE WIRES

6.Haveanassistantsupporttheweightofthexturewhilecompletingthewiring.Cut

away excess wire. Thread the xture’s wires through canopy loop (H) and nipple (F).

Attachthexture’swirestothepowersupplywiresfromthejunctionbox.Connectblack

toblack(orsmooth);whitetowhite(orribbed);groundtoground(greenorcopper).Twist

theendsofthewirepairstogether, and then twist on a wireconnector. Make sureall

twistsareinthesamedirection.Ifthereisnogroundwire(greenorcopper)comingfrom

thejunctionbox,locategroundscrew(E) onmountingstrap(A)andwrapthexture’s

ground wire around the green ground screw (E). Use a screwdriver to secure ground

screw(E)ontothemountingbracket.Tuckallwiresneatlyintothejunctionbox.

House Wires

Fixture Wires

Hot

How to Identify the Fixture’s Wires

Hot Neutral Ground

Smooth

Ribbed

Bare Metal,

Green, or

Green Inner

Thread

Black

White

Black Inner

Thread

White Inner

Thread

FINISHING THE INSTALLATION

7. Push canopy (G) up to the ceiling and slide canopy loop collar (I) up beneath the

canopy.Tightlythreadcanopyloopcollar(I)ontocanopyloop(H)tosecurecanopy(G)

in place.

Installlightbulbs(T-notprovided)inaccordancewiththexture’sspecications.

Donotexceedthemaximumrecommendedwattage.

Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.

Golden Lighting 1048-3P GDW, 0806-S ABI Operating instructions

Related papers

Other documents