Shuttle POS X503 User guide

Brand: Shuttle

Model: POS X503

Category: PC/workstation barebones

Type: User guide

This manual is also suitable for

X50V3L Series Quick Guide

【

English

】

53R-X50V33-2501

 To place the machine on the desk and to carry it, do the following:

 PlacetheX50V3Lonaatsurfacesuchasatable(Picture1),andpullthestand

 upwardstoanangleof30°(Picture2).TocarryormoveyourX50V3Lfullyextend

 theangleto180°(Picture3).

VESA mounting it to the wall

Placing on the desk

Power LED

Webcam

Microphone

LCD Display (Single Touch / Non Touch)(Optional)

Front/Rear/Side View



Runthescreencalibration

program and correct 4 point

locations on screen with the

 panel.

Click

Start / All Programs

/ eGalax Touch

 /CongureUtility

Select

[Tools]tabandclick

[4 Points Calibration]

How to use the Touch Panel (Optional)



Whenthe4pointscalibrationcompleted,press[OK]tocontinue.

4 Point Calibration (Optional)

 X50V3Lbringsdigitallifeforaneasytouchexperience.Experiencetheeaseof

 managingyourdigitallifewithafewtouchesortheuseofthestyluspen.The

 touchofyourngerreplacesthemouseandisallyouneedtointeractwiththe

 X50V3L.



Touchandholdthecenterofthetarget.

 Repeatonfourcornersandthescreenwilladjustautomatically.

Cleaning the screen

 Followtheseguidelinesforcleaningtheoutsideandhandlingthescreenofthecomputer:

 Turnoffthesystemanddisconnectallcables.

Use a damp, or cleaning cloth, soft, lint-free cloth with gentle water only and gently

 wipethescreensurface.

 Donotsprayliquiddirectlyonthescreen.

・Touch=left-clickonthemouse

・Touchandhold=right-clickonthemouse

 Followthesteps(1~3)belowtoconnecttheACadaptertotheDCINjack.

Press the Power Buttontoturnonthesystem.

Poweringonthesystem

Stand / Handle

Stylus pen

Power Button

Power Input

DCIN

USB 2.0 Ports

SD card reader

Microphone Jack

LAN Port

Note:X50V3LcanbemountedtoawallusingaVESAcompatible

 100x100mmwall/armbracket.

 IfyouaremountingyourX50V3Ltothewall,removethecoveronthebackof

 X50V3Lrst.

 Unscrew4screwsofthestandmountandremovethestand.

 TheVESAstandardletsusersmountitontowallseasily.

 Pleaserefertotheuserguideofthewall/armmountkityouboughttoinstallit.

Stereo speakers

Kensington® Lock Port

WiFi LED

COM Ports (Optional)

VGA Port

Note: Theproduct’scolorandspecicationwilldependupontheactuallyshippingproduct.

180

3.2.1.

Printer Port (Optional)

Hard disk drive LED

SafetyInformation

 ReadthefollowingprecautionsbeforesettingupaShuttleX50V3L.

CAUTION

Donotwalkonthepowercordorallowanythingtorestonit.

 Thewarrantydoesnotapplytotheproductsthathavebeendisassembledbyusers.

CAUTION

Dangerofexplosionifbatteryisincorrectlyreplaced.Replaceonlywiththesameor

 equivalenttyperecommendedbythemanufacturer.

 Disposeofusedbatteriesaccordingtothemanufacturer’sinstructions.

Touch

Hold OK

HDMI Port

USB 2.0 Ports

Stand / Handle

Headphone / Line-out Jack

A.BeginInstallation

1. RemovethecoveronthebackofX50V3Lrst,unscrew

 fourscrewsofthestandmountandremovethestand.

Forsafetyreasons,pleaseensurethatthepower

cordisdisconnectedbeforeopeningthecase.

1. LocatetheSODIMMslotonthemainboard.

3. Gentlyinsertthe



 moduleintotheslot



 ina45-degreeangle.

SODIMMslot

5. Repeattheabovestepstoinstalladditionalmemorymodules,

 ifrequired.

Latch

B.HDDInstallation

2. Unscrewthreescrewsofthebracketandremoveit.

3. MountHDDintothebracketwithfourscrews.

4. Asshown,installtheHDD&bracketinthechassisand



 pushittowardsthedirectionasindicatedbytheredarrow



 toconnecttheHDDconnector.

5. TightentheHDD&bracketwiththreescrews.

1. Replacethebackcover,standandrefasteneightscrews.

D.Complete

2. Unscrewfourscrewsofthebackcoverandremoveit.

1. UnscrewfourscrewsoftheVESABaseandremoveitrst.

6.ReplacetheVESABaseandrefastenfourscrews.

2. Replacethecover,complete.

Cover

Screw

VESABase

C.MemoryModuleInstallation

2. Alignthenotchofthe

 memorymodulewith



 theoneofthememory



 slot.

45-degree

angle

4. Carefullypushdownthememorymoduleuntilitsnapsinto

 thelockingmechanism.

HDD

Connector

BackCover

Screw

VESABase

Stand/Handle

Ifyouinstallonlyonememorymoduleinyour

system,installitintheslotlabeled"DIMM2".

DIMM1DIMM2

Shuttle POS X503 User guide

Brand: Shuttle

Model: POS X503

Category: PC/workstation barebones

Type: User guide

This manual is also suitable for

Download PDF

report

Shuttle POS X503 User guide

This manual is also suitable for

Shuttle POS X503 User guide

Related papers

Other documents