2. Computers & electronics
  3. Computers
  4. All-in-One workstations
  5. Shuttle
  6. X 5040TA

Shuttle X 5040TA, POS X504, X 5040VA, X 5040XA Specification

  • Hello! I am an AI chatbot trained to assist you with the Shuttle X 5040TA Specification. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
X50V4 Series Quick Guide
【
English
】
2. Refastenthestandandthebackcoverwitheightscrews.
Toplacethemachineonthedeskandtocarryit,dothefollowing:
PlacetheX50V4onaatsurfacesuchasatable(Picture1),andpullthestand
upwardstoanangleof30°(Picture2).TocarryormoveyourX50V4fullyextend
theangleto180°(Picture3).
E
VESAmountingittothewall
E
Placingonthedesk
E
Front/Rear/SideView
Runthescreencalibration
programandcorrect4point
locationsonscreenwiththe
panel.
ClickStart/AllPrograms
/eGalaxTouch
/CongureUtility
Select[Tools]tabandclick
[4PointsCalibration]
E
HowtousetheTouchPanel
Whenthe4pointscalibrationcompleted,press“OK”tocontinue.
E
4PointCalibration(CD-ROMdriveinstall)
X50V4bringsdigitallifeforaneasytouchexperience.Experiencetheeaseof
managingyourdigitallifewithafewtouchesortheuseofthestyluspen.The
touchofyourngerreplacesthemouseandisallyouneedtointeractwiththe
X50V4.
Touchandholdthecenterofthetarget.
Repeatonfourcornersandthescreenwilladjustautomatically.
E
Cleaningthescreen
Followtheseguidelinesforcleaningtheoutsideandhandlingthescreenofthecomputer:
Turnothesystemanddisconnectallcables.
Useadamp,orcleaningcloth,soft,lint-freeclothwithgentlewateronlyandgently
wipethescreensurface.
・Touch=left-clickonthemouse
・Touchandhold=right-clickonthemouse
Followthesteps(1~3)belowtoconnecttheACadaptertothe“DC-INjack”.
Pressthe“PowerButton”toturnonthesystem.
E
Poweringonthesystem
01
Stand/Handle
02
Microphone
03
Webcam
04
LCDDisplay(SingleTouch)
05
HardDiskDriveLED
06
PowerLED
07
StereoSpeakers
08
PrinterPort(Optional)
Note:TheX50V4canbemountedtoawallusingaVESAcompatible75x75
mmor100x100mmwall/armbracket.
IfyouaremountingyourX50V4tothewall,removethecoveronthebackof
theX50V4rst.
Unscrewfourscrewsofthestandmountandremovethestand.
TheVESAstandardletsusersmountitontowallseasily.
Pleaserefertotheuserguideofthewall/armmountkityouboughttoinstallit.
Note:Theproduct’scolourandspecicationsmayvaryfromtheactuallyshippingproduct.
E
SafetyInformation
ReadthefollowingprecautionsbeforesettingupaShuttleX50V4.
CAUTION
Do
notwalkonthepowercordorallowanythingtorestonit.
CAUTION
Danger
ofexplosionifbatteryisincorrectlyreplaced.Replaceonlywiththesameor
equivalent
typerecommendedbythemanufacturer.
Disposeofusedbatteriesaccordingtothemanufacturer’sinstructions.
Touch
Hold OK
A.BeginInstallation
1. RemovethecoveronthebackoftheX50V4rst,unscrew
fourscrewsofthestandmountandremovethestand.
Forsafetyreasons,pleaseensurethatthepower
cordisdisconnectedbeforeopeningthecase.
Latch
Latch
B.HDDInstallation
1. Unscrewfourscrewsofthebracketandremoveit.
2. MounttheHDDintothebracketwithfourscrews.
1. Replacethebackcover.
D.Complete
2. Unscrewfourscrewsofthebackcoverandremoveit.
3. Replacethecover,complete.
Cover
Screw
4. Carefullypushdownthememorymoduleuntilitsnapsinto
thelockingmechanism.
BackCover
Screw
Stand/Handle
Stand/Handle
02
04
03
05
07
13
14
07
75 x75 mm
100 x 100mm
06
09
08
12
10
11
15
16
17
181922 20212324
09
COM1andCOM2Ports(Optional)
10
VGAPort
11
Kensington
®
LockPort
12
PowerButton
13
StylusPen
14
SDCardReader
15
USB2.0Ports
16
Headphone/Line-outJack
17
MicrophoneJack
18
HDMIPort
HDMI
19
USB3.0Ports
20
LANPort
21
USB2.0Ports
22
DCIn
DC-IN
23
RJ11DIOPortforCashDrawer(Optional)
24
COM3,COM4overRJ45(Optional)
01
Unscrew
1. LocatetheSO-DIMMslotonthemainboard.
3. Gentlyinsertthe
moduleintotheslot
ina45-degreeangle.
SO-DIMMslot
4. InstalltheHDD&bracketinthechassisandtightenthe
HDD&bracketwithfourscrews.
C.MemoryModuleInstallation
2. Alignthenotchofthe
memorymodulewith
theoneofthememory
slot.
45-degree
angle
3. ConnecttheSerialATAandpowercablestotheHDD.
TakeouttheSerialATAandpowercablesfromaccessorybox.
UseDDR3LSO-DIMM
180
3.2.1.
30
53R-X50V43-H101
Thismainboarddoesonlysupport1.35VDDR3L
memorymodules.
/