2. Computers & electronics
  3. Telecom & navigation
  4. Mobile phones
  5. Car kits
  6. Metra Electronics
  7. 99-7009

Metra Electronics 99-7009 User manual

  • Hello! I am an AI chatbot trained to assist you with the Metra Electronics 99-7009 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
INSTALLATION INSTRUCTIONS FOR PART 99-7009
Phillips Screwdriver s Socket Wrench
1-800-221-0932 www.metraonline.com
KIT FEATURES
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
APPLICATIONS
Mitsubishi Endeavor
2004-2010
s DIN Head Unit Provisions
s ISO DIN Head Unit Provisions
A) Radio Housing s B) ISO Brackets s C) Trim Plate
KIT COMPONENTS
T
OOLS REQUIRED:
99-7009
A
B
C
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
s-ITSUBISHIHARNESSUP
s-)4/-ITSUBISHIAMPLIFIED)NTERFACEUP
Antenna Adapter:
s.OTREQUIRED
99-7009
s
Dash$ISASSEMBLY
-Mitsubishi%NDEAVOR----------------------------------
s
Kit!SSEMBLY
-ISOHeadUnitProvisionwithPocket----------------------------
-DINHeadUnitProvisionwithPocket----------------------------
s
FinalAssembly------------------------------------------------------
sNotes----------------------------------------------------------------
TSTNETNOCFOELBA
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take
steps toward a better tomorrow.
99-7009
1
ADYLBMESSASIDHS
2004-2010 MITSUBISHI ENDEAVOR
Disconnect the negative battery terminal
to prevent an accidental short circuit.
Unsnap and remove entire panel sur-
rounding radio and A/C controls.
(Figure A)
1
2
Remove (1) 10MM nut from the rear support
on the top left of radio on cross bar behind
dash. (FIGURE B)
3
Remove (3) Phillips screws to remove
factory radio chassis (Figure C)
4
A
Remove (4) Phillips screws from the pock-
et at the bottom of the radio and A/C panel
and remove the pocket. (This is where the
99-7009 will be mounted.) (Figure D)
5
B
C
D
..",%%.
'
NA7B:HH6I>@
9>C=ZVYJc^iEgdk^h^dc
3LIDE
THE$).CAGEINTOTHE2ADIO
(OUSINGANDSECUREBYBENDING
THEMETALLOCKINGTABSDOWN
3LIDE
THEAFTERMARKETHEADUNIT
INTOTHECAGEANDSECURE 3NAP
TRIMPLATEINTOTHERADIOHOUSING
5SINGTHEFACTORYHARDWARE MOUNT
THEINTHELOCATIONWHERE
THEFACTORYPOCKETRESIDED
..",%%.
(
NA7B:HH6I>@
>HD9>C=:69JC>IEGDK>H>DC
-OUNT
THE)3/"RACKETSTOTHEHEAD
UNITWITHTHESCREWSSUPPLIEDWITH
THEUNIT
3LIDE
THEHEADUNITINTOTHERADIO
OPENINGUNTILTHESIDECLIPSENGAGE
3N
APTHE4RIMPLATEINTOTHE2ADIO
(OUSING
..",%%.
)
NA7B:HH6A6C>;
!
,OC
ATETHEFACTORYWIRINGHARNESSINTHEDASH
-ETRARECOMMENDSUSINGTHEPROPERMATING
ADAPTERANDMAKINGTHECONNECTIONSAS
SHOWN )SOLATEANDINDIVIDUALLYTAPEOFFTHE
ENDSOFANYUNUSEDWIRESTOPREVENTELECTRICAL
SHORTCIRCUIT3EEFIGURE!
2ECONNECTTHENEGATIVEBATTERYTERMINALANDTEST
THEUNITFORPROPEROPERATION
! 3TRIPWIREENDSBACK
" 4WISTENDSTOGETHER
# 3OLDER
$ 4APE
2EASSEMBLERADIOANDDASHASSEMBLIESIN
REVERSEORDEROFDISASSEMBLY
"
#
$
..",%%.
*
H:IDC
INST997009
1-800-221-0932 www.metraonline.com
Rev. 04-26-10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-7009
/