Metra Electronics 99-7008 User manual

99-7008
Brand
Metra Electronics
Model
99-7008
Category
Car kits
Type
User manual

Metra Electronics 99-7008 is a dash kit designed to help you install a new radio into your 2003-2006 Mitsubishi Outlander. It comes with a DIN radio provision with pocket, an ISO radio provision with pocket, and all the necessary hardware for installation. With this kit, you can easily replace your factory radio with a new aftermarket unit that fits seamlessly into your vehicle's dashboard.

Metra Electronics 99-7008 is a dash kit designed to help you install a new radio into your 2003-2006 Mitsubishi Outlander. It comes with a DIN radio provision with pocket, an ISO radio provision with pocket, and all the necessary hardware for installation. With this kit, you can easily replace your factory radio with a new aftermarket unit that fits seamlessly into your vehicle's dashboard.

INSTALLATION INSTRUCTIONS FOR PART 99-7008
1-800-221-0932 www.metraonline.com
KIT FEATURES
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
• DIN Radio Provision with pocket
• ISO Radio Provision with pocket
A) Radio Housing B) ISO Brackets C) ISO Trim Plate
KIT COMPONENTS
TOOLS REQUIRED:
99-7008
APPLICATIONS
2003-2006
Mitsubishi Outlander
C
B
A
• Phillips Scr
ewdriver
Panel Remo
v
al Tool or
Small Flat Blade Screwdriver
Dash Disassembly ............................................................................ 1
Kit Assembly
Din Mount Radio Provision with pocket..........................................................
2
ISO Mount Radio Provision with pocket..........................................................
3
Final Assembly
................................................................................. 4
99-7008
TABLE OF CONTENTS
2003-2006 Mitsubishi Outlander
99-7008
DASH DISASSEMBLY
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Remove all (3) climate control knobs.
(Figure A)
2
MITSUBISHI OUTLANDER 2003-2006
Remove (2) Phillips head screws
from behind the (2) outside climate
control knobs.
(Figure A)
3
Unsnap the top edge of the trim
panel below the Climate controls. It
is not necessary to completely
remove this panel.
(Figure B)
4
Unsnap and remove the radio/climate
control trim panel.
(Figure C)
5
A
B
C
1
Remove (4) Phillips head screws
securing the radio. Unplug and
remove the radio.
6
2
Slide the DIN cage (supplied with radio)
into the Radio Housing from the front.
(Figure A)
1
A
Slide the radio into the DIN cage until it
snaps into place.
(Figure C)
3
DIN MOUNT RADIO PROVISION WITH POCKET
B
99-7008
KIT ASSEMBLY
Secure DIN cage to radio housing by
bending the locking tabs outward.
(Figure B)
2
Continue to final assembly.
C
3
Align the holes in the ISO brackets with
the holes in the radio. Mount the
brackets to the radio using screws
supplied with the radio.
(Figure A)
1
A
B
Slide the radio/bracket assembly into the
radio housing until it snaps into place.
(Figure B)
2
Snap the ISO trim-plate onto the front of
the assembled radio and housing.
(Figure C)
NOTE: To remove the radio unsnap and remove the ISO trim-plate. Using a flat
blade screwdriver disengage ISO brackets from the radio housing and slide
radio out of radio housing.
3
ISO MOUNT RADIO WITH POCKET
99-7008
KIT ASSEMBLY
Continue to final assembly.
C
4
FINAL ASSEMBLY
1
Locate the factory wiring harness in the dash and make the connection as shown.
Metra recomends using the proper mating adapter and making the connections as
shown. (Isolate and individually tape off the ends of any unused wires to prevent
electrical short circuit.)
2
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground
. . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-). . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
METRA / EIA WIRING CODE
FINAL WIRING CONNECTIONS
99-7008
FINAL ASSEMBLY
3
5
99-7008
NOTES
99-7008 INSTRUCTIONS
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST99-7008
REV. 03/14/06
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Metra Electronics 99-7008 User manual

99-7008
Brand
Metra Electronics
Model
99-7008
Category
Car kits
Type
User manual

Metra Electronics 99-7008 is a dash kit designed to help you install a new radio into your 2003-2006 Mitsubishi Outlander. It comes with a DIN radio provision with pocket, an ISO radio provision with pocket, and all the necessary hardware for installation. With this kit, you can easily replace your factory radio with a new aftermarket unit that fits seamlessly into your vehicle's dashboard.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents