WAGO 4-channel, ± 10VDC, single ended User manual

Brand: WAGO

Model: 4-channel, ± 10VDC, single ended

Type: User manual

Pos: 2 /Dokumentation allgemein/Einband/Einband Handbuch - Fronts eite 20 15 - mit Doc Var iabl en ( Sta ndar d) @ 9\ mod_1285229289866_0.docx @ 64941 @ @ 1

WAGO-I/O-SYSTEM 750

Manual

750-457(/xxx-xxx)

4AI ±10V DC S.E.

4-Channel Analog Input Module ±10 V, Single-

ended

Version 1.2.0

Pos: 3 /A lle Ser ien ( All ge mein e M odul e)/ Hin weis e z ur D oku men tati on/I mpr ess um für Sta ndardhandbücher - allg . Anga ben, Ans chri ften, Tel efo nnummer n und E-M ail- Adres sen @ 3\mod_1219151118203_21.docx @ 21060 @ @ 1

2 WAGO-I/O-SYSTEM 750

750-457 4AI ±10V DC S.E.

Manual

Version 1.2.0

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D-32423 Minden

Phone: +49 (0) 571/8 87 – 0

Fax: +49 (0) 571/8 87 – 1 69

E-Mail: [email protected]

Web: http://www.wago.com

Technical Support

Phone: +49 (0) 571/8 87 – 5 55

Fax: +49 (0) 571/8 87 – 85 55

E-Mail: [email protected]

Every conceivable measure has been taken to ensure the accuracy and

completeness of this documentation. However, as errors can never be fully

excluded, we always appreciate any information or suggestions for improving the

documentation.

E-Mail: [email protected]

We wish to point out that the software and hardware terms as well as the

trademarks of companies used and/or mentioned in the present manual are

generally protected by trademark or patent.

=== Ende der Lis te f ür T e xtmar ke Ei nb and _vor ne = ==

WAGO-I/O-SYSTEM 750 Table of Contents 3

750-457 4AI ±10V DC S.E.

Manual

Version 1.2.0

Pos: 5 /D ok ument ati on al lg em ein/V erz eic hni sse /Inh alts ver zei chni s - Ü bersc hrift oG und Ver zeich nis @ 3\mod_1219151230875_21.docx @ 21063 @ @ 1

Table of Contents

1 Notes about this Documentation ................................................................. 5

1.1 Validity of this Documentation ................................................................. 5

1.2 Copyright ................................................................................................... 5

1.3 Symbols ..................................................................................................... 6

1.4 Number Notation ....................................................................................... 8

1.5 Font Conventions ...................................................................................... 8

2 Important Notes ........................................................................................... 9

2.1 Legal Bases ............................................................................................... 9

2.1.1 Subject to Changes ............................................................................... 9

2.1.2 Personnel Qualifications ....................................................................... 9

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with Underlying

Provisions ............................................................................................. 9

2.1.4 Technical Condition of Specified Devices ......................................... 10

2.2 Safety Advice (Precautions) .................................................................... 11

3 Device Description ..................................................................................... 13

3.1 View ........................................................................................................ 14

3.2 Connectors ............................................................................................... 15

3.2.1 Data Contacts/Internal Bus ................................................................. 15

3.2.2 Power Jumper Contacts/Field Supply ................................................ 16

3.2.3 CAGE CLAMP

Connectors ............................................................. 18

3.3 Display Elements .................................................................................... 19

3.4 Operating Elements ................................................................................. 19

3.5 Schematic Diagram ................................................................................. 20

3.6 Technical Data ........................................................................................ 21

3.6.1 Device ................................................................................................. 21

3.6.2 Supply ................................................................................................. 21

3.6.3 Communication .................................................................................. 21

3.6.4 Inputs .................................................................................................. 21

3.6.5 Climatic Environmental Conditions ................................................... 22

3.6.6 Connection Type ................................................................................ 22

3.7 Approvals ................................................................................................ 23

3.8 Standards and Guidelines ........................................................................ 25

4 Process Image ............................................................................................. 26

5 Mounting ..................................................................................................... 28

5.1 Mounting Sequence ................................................................................. 28

5.2 Inserting and Removing Devices ............................................................ 29

5.2.1 Inserting the I/O Module .................................................................... 29

5.2.2 Removing the I/O Module .................................................................. 30

6 Connect Devices ......................................................................................... 31

6.1 Connecting a Conductor to the CAGE CLAMP

................................... 31

6.2 Connection Example ............................................................................... 32

7 Use in Hazardous Environments .............................................................. 33

7.1 Marking Configuration Examples ........................................................... 34

7.1.1 Marking for Europe According to ATEX and IEC-Ex ...................... 34

4 Table of Contents WAGO-I/O-SYSTEM 750

750-457 4AI ±10V DC S.E.

Manual

Version 1.2.0

7.1.2 Marking for America According to NEC 500 .................................... 39

7.2 Installation Regulations ........................................................................... 40

7.2.1 Special Conditions for Safe Use (ATEX Certificate TÜV 07 ATEX

554086 X) ........................................................................................... 41

7.2.2 Special Conditions for Safe Use (ATEX Certificate TÜV 12 ATEX

106032 X) ........................................................................................... 42

7.2.3 Special Conditions for Safe Use (IEC-Ex Certificate TUN 09.0001 X)43

7.2.4 Special Conditions for Safe Use (IEC-Ex Certificate IECEx TUN

12.0039 X) .......................................................................................... 44

7.2.5 Special Conditions for Safe Use According to ANSI/ISA 12.12.01 .. 45

List of Figures ...................................................................................................... 46

List of Tables ........................................................................................................ 47

=== Ende der Lis te f ür T e xtmar ke V erz eic hnis _vor ne == =

WAGO-I/O-SYSTEM 750 Notes about this Documentation 5

750-457 4AI ±10V DC S.E.

Manual

Version 1.2.0

Pos: 7 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten für all e Ser ie n/Hi nwei se zur D o kume nt ation /Hi nw eise zu dies er D o kume ntati on - Ü ber schr if t 1 @ 4\ mod_1237987661750_21. doc x @ 29 029 @ 1 @ 1

1 Notes about this Documentation

Pos: 8 /A lle Ser ien ( All ge mein e M odul e)/ Hin weis e z ur D oku men tati on/H i nweis e/Hi n weis : D okum ent atio n a ufbe wahr e n @ 4 \mod_1237987339812_21.docx @ 29026 @ @ 1

Always retain this documentation!

This documentation is part of the product. Therefore, retain the documentation

during the entire service life of the product. Pass on the documentation to any

subsequent user. In addition, ensure that any supplement to this documentation is

included, if necessary.

Pos: 9 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten für all e Ser ie n/Hi nwei se zur D o kume nt ation /G ültig kei tsb erei ch - Ü b ersc hrif t 2 @ 1 2\mod_1338912448776_21.docx @ 96469 @ 2 @ 1

1.1 Validity of this Documentation

Pos: 10 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Hi nweis e zur D okum ent ati on/G ülti gkei ts berei c h/Gül tig kei tsber ei ch D oku men tat ion Bus kle mme 75 0-xx xx, S tan dar dvers ion un d au fg elist et e Var iant e n @ 1 4\mod_1358944038682_21.doc x @ 109354 @ @ 1

This documentation is only applicable to the I/O module 750-457 (4AI ±10V DC

S.E.) and the variants listed in the table below.

Pos: 11 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on/G ülti gkei ts berei c h/Var iant e nlist en/ Var iant enli st e - 7 50-xxx - Stan dard version und Variante /025-000 ( erw eiter ter Te mper at urb ereic h) @ 9\ mod_1281521920414_21.docx @ 63093 @ @ 1

Table 1: Variants

Item Number/Variant

Designation

750-457

4AI ±10V DC S.E.

750-457/025-000

4AI ±10V DC S.E./T

Pos: 12 /A ll e Ser ien (Al lg emei ne M od ule)/ Hi nweis e zur D o kume ntati on /Hi nwei se/ Hin weis : G ülti g keit d er Anga ben für aufg el iste te V ari ant en @ 9\mod_1281520778141_21.docx @ 63085 @ @ 1

Documentation Validity for Variants

Unless otherwise indicated, the information given in this documentation applies to

listed variants.

Pos: 13 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on/Hi nw eise /Ac htung: Hinweis zur Dokumentation Busklemmen 750-xxxx @ 4\mod_1237986979656_21.doc x @ 29023 @ @ 1

The I/O module 750-457 shall only be installed and operated according to the

instructions in this manual and in the manual for the used fieldbus

coupler/controller.

Consider power layout of the WAGO-I/O-SYSTEM 750!

In addition to these operating instructions, you will also need the manual for the

used fieldbus coupler/controller, which can be downloaded at www.wago.com.

There, you can obtain important information including information on electrical

isolation, system power and supply specifications.

Pos: 14.1 /All e Seri en ( All ge meine Mo dul e)/H in weis e zur D oku ment ati on/U rh eber sc hutz aus führ lic h @ 4\mod_1235565145234_21.doc x @ 27691 @ 2 @ 1

1.2 Copyright

This Manual, including all figures and illustrations, is copyright-protected. Any

further use of this Manual by third parties that violate pertinent copyright

provisions is prohibited. Reproduction, translation, electronic and phototechnical

filing/archiving (e.g., photocopying) as well as any amendments require the

written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.

Non-observance will involve the right to assert damage claims.

Pos: 14.2 /Dokumentation allgemein/Gliederungselemente/---S eite nwe chsel --- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

6 Notes about this Documentation WAGO-I/O-SYSTEM 750

750-457 4AI ±10V DC S.E.

Manual

Version 1.2.0

Pos: 14 .3 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en f ür alle S erie n/Hi nwei se z ur Dok um enta tio n/S ymbol e - Ü bers chr ift 2 @ 1 3\mod_1351068042408_21.docx @ 105270 @ 2 @ 1

1.3 Symbols

Pos: 14 .4.1 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinweise/Gefahr/Gefahr: _Warnung vor Personenschäden allgemei n_ - Erläu terung @ 13\ mod_1343309450020_21.docx @ 101029 @ @ 1

Personal Injury!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 14 .4.2 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinweise/Gefahr/Gefahr : _War nung vor Person ensch äden dur ch ele ktris chen St rom_ - Erläuterung @ 13\mod_1343309694914_21.docx @ 101030 @ @ 1

Personal Injury Caused by Electric Current!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 14 .4.3 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nsti ge H inw eis e/W arn ung/ War nung : _ War nu ng vor P erso nens ch äde n all ge mei n_ - Erläuterung @ 13\mod_1343309877041_21.docx @ 101035 @ @ 1

Personal Injury!

Indicates a moderate-risk, potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Pos: 14 .4.4 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nsti ge H inw eis e/V orsic ht /Vor sic ht: _War nu ng vor P ers one nsc häde n al lg emei n_ - Erläuterung @ 13\mod_1343310028762_21.docx @ 101038 @ @ 1

Personal Injury!

Indicates a low-risk, potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Pos: 14.4 .5 /Alle Ser ie n ( Allg emei ne M od ule) /Wic hti ge Erlä ut erung en/ Sic her heit s- und sonstige Hinweise/Achtung/Achtung: _Warnung vor Sac hschäden allgemein_ - Erläuterung @ 13\mod_1343310134623_21.doc x @ 101041 @ @ 1

Damage to Property!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 14 .4.6 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Si cher hei ts- und sonstige Hinweise/Achtung/Achtung: _Warnung vor Sac hschäden durch elektrostatische Aufladung_ - Erläuterung @ 13\mod_1343310227702_21.docx @ 101044 @ @ 1

Damage to Property Caused by Electrostatic Discharge (ESD)!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 14 .4.7 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinweise/Hinweis/Hinweis: _Wichtiger Hinweis allgemein_ - Erläuterung @ 13\mod_1343310326906_21.docx @ 101047 @ @ 1

Important Note!

Indicates a potential malfunction which, if not avoided, however, will not result in

damage to property.

Pos: 14 .4.8 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinwei se/I nfor matio n/Infor mati on: _W eitere I nfor mation al lge mein_ - Erl äuter ung @ 13 \mod_1343310439814_21.docx @ 101051 @ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7

750-457 4AI ±10V DC S.E.

Manual

Version 1.2.0

Additional Information:

Refers to additional information which is not an integral part of this

documentation (e.g., the Internet).

Pos: 14.5 /Dokumentation allgemein/Gliederungselemente/---S eite nwe chsel --- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

8 Notes about this Documentation WAGO-I/O-SYSTEM 750

750-457 4AI ±10V DC S.E.

Manual

Version 1.2.0

Pos: 14 .6 /All e Seri en (Allg emeine Modul e)/Hi nweis e zur Do kument ation /Zahl ensy steme @ 3\ mod_1221059454015_21.docx @ 21711 @ 2 @ 1

1.4 Number Notation

Table 2: Number Notation

Number Code

Example

Note

Decimal

100

Normal notation

Hexadecimal

0x64

C notation

Binary

'100'

'0110.0100'

In quotation marks, nibble separated with

dots (.)

Pos: 14.7 /All e Seri en ( All ge meine Mo dule) /Hin weise zur Doku mentat ion/S chrif tkon venti onen @ 3\ mod_1221059521437_21.docx @ 21714 @ 2 @ 1

1.5 Font Conventions

Table 3: Font Conventions

Font Type

Indicates

italic

Names of paths and data files are marked in italic-type.

e.g.: C:\Program Files\WAGO Software

Menu items are marked in bold letters.

e.g.: Save

A greater-than sign between two names means the selection of a

menu item from a menu.

e.g.: File > New

Input

Designation of input or optional fields are marked in bold letters,

e.g.: Start of measurement range

“Value”

Input or selective values are marked in inverted commas.

e.g.: Enter the value “4 mA” under Start of measurement range.

[Button]

Pushbuttons in dialog boxes are marked with bold letters in square

brackets.

e.g.: [Input]

[Key]

Keys are marked with bold letters in square brackets.

e.g.: [F5]

Pos: 15 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 9

750-457 4AI ±10V DC S.E.

Manual

Version 1.2.0

Pos: 16 /A ll e Ser ien (Al lg emei ne M od ule)/ Über schrif ten für alle Ser ien/ Wichti ge Erlä uteru ngen/ Wich tige Er läuter ungen - Übersc hrift 1 @ 4\mod_1241428899156_21.docx @ 32170 @ 1 @ 1

2 Important Notes

Pos: 17.1 /All e Seri en ( All ge meine Do kum ente) ( All ge meine Mo dule) /Wi cht ige Erl äut eru nge n/Wi chti ge Erl äut erung en - Einl eitung @ 3\mod_1221059818031_21.docx @ 21717 @ @ 1

This section includes an overall summary of the most important safety

requirements and notes that are mentioned in each individual section. To protect

your health and prevent damage to devices as well, it is imperative to read and

carefully follow the safety guidelines.

Pos: 17.2 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en f ür alle S erie n/Wi chti ge Erl äuter u ngenR ec htlic he Gr undl ag en - Üb ersc hrift 2 @ 3\ mod_1221060626343_21.docx @ 21726 @ 2 @ 1

2.1 Legal Bases

Pos: 17.3 /Alle Serien (Allgemeine Dokumente) (Allgemeine Module)/Wichtige Erläuterungen/Änderungs vorbehalt - Über sc hrift 3 un d In halt @ 3\ mod_1221060036484_21.docx @ 21720 @ 3 @ 1

2.1.1 Subject to Changes

WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any

alterations or modifications that serve to increase the efficiency of technical

progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from

the granting of patents or from the legal protection of utility patents. Third-party

products are always mentioned without any reference to patent rights. Thus, the

existence of such rights cannot be excluded.

Pos: 17.4 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Pers onalq uali fikati onPer sonal qual ifika tion 750- xxxx - Ü bersc hrift 3 u nd Inhal t @ 3\mod_1224061208046_21.docx @ 24063 @ 3 @ 1

2.1.2 Personnel Qualifications

All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be

carried out by electrical specialists with sufficient knowledge in automation. The

specialists must be familiar with the current norms and guidelines for the devices

and automated environments.

All changes to the coupler or controller should always be carried out by qualified

personnel with sufficient skills in PLC programming.

Pos: 17 .5 /Serie 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterungen/Bestimmungsgemäße VerwendungBestimmungsgemäße Verwendung 750-xxxx - Über schri ft 3 un d I nhal t @ 3\ mod_1224064151234_21.docx @ 24070 @ 3 @ 1

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with

Underlying Provisions

Fieldbus couplers, fieldbus controllers and I/O modules found in the modular

WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and

transmit them to actuators or higher-level control systems. Using programmable

controllers, the signals can also be (pre-) processed.

The devices have been developed for use in an environment that meets the IP20

protection class criteria. Protection against finger injury and solid impurities up to

12.5 mm diameter is assured; protection against water damage is not ensured.

Unless otherwise specified, operation of the devices in wet and dusty

environments is prohibited.

Operating the WAGO-I/O-SYSTEM 750 devices in home applications without

further measures is only permitted if they meet the emission limits (emissions of

interference) according to EN 61000-6-3. You will find the relevant information

in the section “Device Description” > “Standards and Guidelines” in the manual

for the used fieldbus coupler/controller.

10 Important Notes WAGO-I/O-SYSTEM 750

750-457 4AI ±10V DC S.E.

Manual

Version 1.2.0

Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-

SYSTEM 750 in hazardous environments. Please note that a prototype test

certificate must be obtained that confirms the correct installation of the system in

a housing or switch cabinet.

Pos: 17.6 /All e Seri en ( All ge meine Do kum ente) ( Allg emei ne Mo dule) /Wi chti ge Erl äut eru nge n/Tec hni sc her Z ust an d d er G erät e - Üb ersc hrift 3 un d Inhal t @ 3\mod_1221060446109_21.docx @ 21723 @ 3 @ 1

2.1.4 Technical Condition of Specified Devices

The devices to be supplied ex works are equipped with hardware and software

configurations, which meet the individual application requirements. WAGO

Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of

changes in hardware or software as well as to non-compliant usage of devices.

Please send your request for modified and new hardware or software

configurations directly to WAGO Kontakttechnik GmbH & Co. KG.

Pos: 17.7 /Dokumentation allgemein/Gliederungselemente/---S eite nwe chsel --- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 11

750-457 4AI ±10V DC S.E.

Manual

Version 1.2.0

Pos: 17 .8 /All e Seri en (All gemei ne Mod ule)/Ü bersc hrift en für al le Seri en/Wi chtig e Erläut erung enSic herhei tshi nweis e - Über schr ift 2 @ 6\mod_1260180299987_21.docx @ 46724 @ 2 @ 1

2.2 Safety Advice (Precautions)

Pos: 17.9 /Alle Serien (Allgemeine Dokumente) (Allgemeine Module)/Wic htige Erläut erung en/Si cherh eits hinwei se/Ei nleit ung Sic herh eitshi nweis e Hard ware @ 6\mod_1260180170493_21.docx @ 46720 @ @ 1

For installing and operating purposes of the relevant device to your system the

following safety precautions shall be observed:

Pos: 17.1 0. 1 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : N ich t an G erät en unter Sp ann ung arbei te n! @ 6\ mod_1260180365327_21.docx @ 46727 @ @ 1

Do not work on devices while energized!

All power sources to the device shall be switched off prior to performing any

installation, repair or maintenance work.

Pos: 17.1 0. 2 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d s onsti ge H in wei se/G ef ahr/ Gefa hr: Ei nbau 07 50- xxxx nur in Ge häuse n, Schr änken o der ele ktrisc hen Be triebs räume n! @ 6\mod_1260180556692_21.doc x @ 46731 @ @ 1

Install the device only in appropriate housings, cabinets or in electrical

operation rooms!

The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,

install the system and its components exclusively in appropriate housings,

cabinets or in electrical operation rooms. Allow access to such equipment and

fixtures to authorized, qualified staff only by means of specific keys or tools.

Pos: 17.1 0. 3 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : Unfallverh üt ungs vors chr ift en b eac hte n! @ 6\mod_1260180657000_21.doc x @ 46735 @ @ 1

Pos: 17.1 0. 4 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : A uf normg er echt e n Ansc hlu ss ac hten! @ 6 \mod_1260180753479_21.docx @ 46739 @ @ 1

Pos: 17.1 1. 1 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : Defek te oder besch ädigt e Gerät e austaus chen! @ 6\mod_1260180857358_21.docx @ 46743 @ @ 1

Replace defective or damaged devices!

Replace defective or damaged device/module (e.g., in the event of deformed

contacts), since the long-term functionality of device/module involved can no

longer be ensured.

Pos: 17.1 1. 2 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : G erät e vor kriec hen den und i sol ier e nden Sto ffen s chütz en! @ 6\mod_1260181036216_21.doc x @ 46747 @ @ 1

Protect the components against materials having seeping and insulating

properties!

The components are not resistant to materials having seeping and insulating

properties such as: aerosols, silicones and triglycerides (found in some hand

creams). If you cannot exclude that such materials will appear in the component

environment, then install the components in an enclosure being resistant to the

above-mentioned materials. Clean tools and materials are imperative for handling

devices/modules.

Pos: 17.1 1. 3 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : Rei nig ung nur mi t zul äss ig en M at erial ien! @ 6\mod_1260181203293_21.doc x @ 46751 @ @ 1

Clean only with permitted materials!

Clean soiled contacts using oil-free compressed air or with ethyl alcohol and

leather cloths.

Pos: 17.1 1. 4 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : K ein K ont a ktspra y verw end en! @ 6\ mod_1260181290808_21.docx @ 46755 @ @ 1

12 Important Notes WAGO-I/O-SYSTEM 750

750-457 4AI ±10V DC S.E.

Manual

Version 1.2.0

Do not use any contact spray!

Do not use any contact spray. The spray may impair contact area functionality in

connection with contamination.

Pos: 17.1 1. 5 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : V erpol ung ver mei de n! @ 6\mod_1260184045744_21.docx @ 46767 @ @ 1

Do not reverse the polarity of connection lines!

Avoid reverse polarity of data and power supply lines, as this may damage the

devices involved.

Pos: 17.1 1. 6 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : Elektr ostat isch e Entla dung v ermeid en! @ 6\mod_1260181364729_21.doc x @ 46759 @ @ 1

Avoid electrostatic discharge!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge when touched. Please observe the safety precautions

against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the

devices, please ensure that environmental factors (personnel, work space and

packaging) are properly grounded.

Pos: 18 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 13

750-457 4AI ±10V DC S.E.

Manual

Version 1.2.0

Pos: 19 /All e Seri en ( All ge mein e Mo dul e)/Ü ber schr if ten f ür alle Ser ie n/Ger äte bes chr eib ung /Ger äte besc hr eibu ng - Über schri ft 1 @ 3\mod_1233756084656_21.docx @ 27096 @ 1 @ 1

3 Device Description

Pos: 20.1 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/A nwendung/AI/Anwendung 750-04xx AI SE (+ -10V) @ 5\ mod_1246012072807_21.docx @ 36230 @ @ 1

The Analog Input Module 750-457 (4AI ±10V DC S.E.) processes analog signals

with the norm value of ±10 VDC.

Pos: 20.2 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/I/ O-B eschr ei bung/ AI/I /O- Beschr eib ung 750- 04xx 4 AI SE Fel ddsig nale über AI1 un d Masse bz w. AI2/ 3/4 und M asse @ 5\ mod_1246370579270_21.docx @ 36366 @ @ 1

The module has 4 input channels. The signals of the field side may be received via

the CAGE CLAMP

connectors AI 1 and common (ground) or AI 2, AI 3, AI 4

and common (ground) each.

The common (ground) contacts of all 4 channels have 1 common 0 V ground

potential.

Pos: 20.3 /Serie 750 (WAGO-I/O-SY STEM )/ Ger äteb esc hrei bu ng/Ei nlei tu ng/ An alogei ng ang skl emm en/G erä te beschr ei bu ng 7 50-04 53; - 045 7, -0459 Hinweis @ 16\mod_1379320784828_21.docx @ 131624 @ @ 1

Common 0 V ground potential

This potential is not the 0 V field power of the blade contacts!

Pos: 20.4 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /Ei nlei tu ng/F un ktio n/Gal vani s che T ren nung Ei ng angs sig nal/ S yste meb ene ( 12 B it) @ 6\mod_1255353269263_21.docx @ 42550 @ @ 1

The input signal is electrically isolated and is transmitted with a resolution of

12 bits.

Pos: 20.5 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/L ED-A nzei ge/ LED Fehl er Ber eic hsüb er-/ unt ersc hrei tu ng @ 1 5\mod_1370281145613_21.docx @ 121530 @ @ 1

One red error LED per channel indicates when the measuring range is exceeded or

falls below for the respective channel.

Pos: 20.6 /Serie 750 (WAGO-I/O-SYST EM)/ Ger ätebesc hrei bung/Ei nlei tung /Vers orgung /Anor dnung unter Berüc ksich tigung d er Leist ung skont akte beli ebig @ 3\mod_1233756233468_21.docx @ 27099 @ @ 1

With consideration of the power jumper contacts, the individual modules can be

arranged in any combination when configuring the fieldbus node. An arrangement

in groups within the group of potentials is not necessary.

Pos: 20.7 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte bes chr ei bung /Ei nlei tung /V ers org ung/ Spa nnu ngs vers org ung aus Syst e mspa nnu ng @ 5\mod_1247116433759_21.doc x @ 36920 @ @ 1

Power to the internal electronics is supplied via internal data bus.

Pos: 20.8 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bung/Einlei tung/Versorgung/Vers orgung 24 V, 0 V über Leistungskontakte _ Weitergabe ohne eigene Verwendung @ 16\mod_1379319855936_21.docx @ 131620 @ @ 1

The I/O module receives the 24 V voltage supply and the 0 V potential for the

field level from an upstream I/O module or from the fieldbus coupler/controller

via the power jumper contacts used as blade contacts. These potentials are passed

through without being used galvanically isolated to subsequent I/O modules.

Pos: 20.9 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htig e Erläut erung en/Si cherh eits- und sonstig e Hinwei se/ Achtu ng/Ach tung : Maxi maler Str om Lei stungs konta kte 10 A @ 3\ mod_1226499143500_21.docx @ 25029 @ @ 1

Do not exceed maximum current via power jumper contacts!

The maximum current to flow through the power jumper contacts is 10 A.

Greater currents can damage the contacts.

When configuring your system, ensure that this current is not exceeded. If

exceeded, insert an additional supply module.

Pos: 20.1 0 / Ser ie 7 50 ( WAG O-I/ O-SYST EM)/ Gerät ebesc hreib ung/ Einlei tung/ Einsa tzber eich/ Einsa tzber eich 7 50-xxx x al le K op pler/C o ntrol ler oh ne Ec o nomy- Kop pler @ 3\ mod_1232541867468_21.docx @ 26 525 @ @ 1

The I/O module 750-457 can be used with all fieldbus couplers/controllers of the

WAGO-I/O-SYSTEM 750 (except for the economy types 750-320, -323, -324

and -327).

Pos: 20.1 1 / Ser ie 7 50 ( WAG O-I/ O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tung /I/ O-Be schr eib ung /All ge mein/ V erwei s a uf K apit el " Ans chl üss e" @ 8\ mod_1276775378035_21.doc x @ 57956 @ @ 1

The assignment of the connections is described in the “Connectors” section.

Pos: 20.1 2 / Ser ie 7 50 ( WAG O-I/ O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tung /I/ O-Be schr eib ung /All ge mein/ V erwei s a uf K apit el " Ger ät e ansc hli eß en" > " Ansc hlus sb eispi el (e)" @ 5 \mod_1246015203281_21.docx @ 36298 @ @ 1

Connection examples are shown in section “Connecting Devices” > … >

“Connection Example(s)”.

14 Device Description WAGO-I/O-SYSTEM 750

750-457 4AI ±10V DC S.E.

Manual

Version 1.2.0

Pos: 21 /Do kument ation al lge mein/Gl ieder ungs elem ente/---Sei te nwec hsel --- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

Pos: 22 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/A nsic ht - Ü b erschr if t 2 @ 4\ mod_1240984217343_21.docx @ 3195 8 @ 2 @ 1

3.1 View

Pos: 23 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Gerät ebesc hrei bung/A nsic ht/A nalogei nga ngskle mmen/ Ansic ht 750-0457 @ 15\mod_1370249314830_21.docx @ 121389 @ @ 1

Figure 1: View

Pos: 24 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung /Ans ic ht/A nsi cht C ag eCl amp® _ Leg ende mit LED s @ 15\ mod_1370867188922_21.docx @ 122225 @ @ 1

Table 4: Legend for Figure “View”

Pos.

Description

Details See Section

Marking possibility with Mini-

WSB

---

Status LEDs

“Device Description” > “Display Elements”

Data contacts

“Device Description” > “Connectors”

CAGE CLAMP

connectors

“Device Description” > “Connectors”

Power jumper contacts

“Device Description” > “Connectors”

Release tab

“Mounting” > “Inserting and Removing

Devices”

Pos: 25 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 15

750-457 4AI ±10V DC S.E.

Manual

Version 1.2.0

Pos: 26 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/A nsc hlüs se - Über schri ft 2 @ 4\mod_1240984262656_21.docx @ 31961 @ 2 @ 1

3.2 Connectors

Pos: 27 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsc hlüss e/D ate nko ntakt e/Klemmenbus - Über schri ft 3 @ 6\mod_1256294684083_21.doc x @ 43660 @ 3 @ 1

3.2.1 Data Contacts/Internal Bus

Pos: 28.1 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/A nsc hlüss e/D ate nkon takt e - F eldbu sko ppler /-c ontr oll er, A bbi ld ung und Besc hrei bu ng @ 3\mod_1231771259187_21.doc x @ 26002 @ @ 1

Communication between the fieldbus coupler/controller and the I/O modules as

well as the system supply of the I/O modules is carried out via the internal bus. It

is comprised of 6 data contacts, which are available as self-cleaning gold spring

contacts.

Figure 2: Data Contacts

Pos: 28.2 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herh eits- und so nstig e H inw eis e/Ac htu ng/A ch tung : Bus kl em men nic ht a uf G oldf eder kon ta kte l eg en! @ 7 \mod_1266318463636_21. docx @ 50695 @ @ 1

Do not place the I/O modules on the gold spring contacts!

Do not place the I/O modules on the gold spring contacts in order to avoid soiling

or scratching!

Pos: 28.3 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- und sonstige Hinweise/Achtung/Achtung: ESD - Auf g ute Erd ung der Umg ebu ng ac ht en! @ 7\ mod_1266318538667_21.docx @ 50708 @ @ 1

Ensure that the environment is well grounded!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge. When handling the devices, ensure that the environment

(persons, workplace and packing) is well grounded. Avoid touching conductive

components, e.g. data contacts.

Pos: 29 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

16 Device Description WAGO-I/O-SYSTEM 750

750-457 4AI ±10V DC S.E.

Manual

Version 1.2.0

Pos: 30 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsc hlüss e/L eist ung skont akt e/F eld vers orgu ng - Üb ersc hrift 3 @ 6\ mod_1256294692864_21.docx @ 43664 @ 3 @ 1

3.2.2 Power Jumper Contacts/Field Supply

Pos: 31.1 /S erie 750 (WAGO-I/O-SYST EM)/ Wichti ge Erlä uteru ngen/ Sich erheit s- und so nstig e H inw eis e/Vor sic ht/ Vor sic ht: Verl etz ungs ge fahr dur ch s ch arf kant ige M ess er kont akt e! @ 6\mod_1256193279401_21.docx @ 43414 @ @ 1

Risk of injury due to sharp-edged blade contacts!

The blade contacts are sharp-edged. Handle the I/O module carefully to prevent

injury.

Pos: 31.2 /Serie 750 (WAGO-I/O-SYST EM)/ Ger ätebes chr ei bung /Ans chl üss e/L eist ung s konta kte 2 LK (M ess er/ Leis tung sk onta kte 2 L K (Me sser /F ed er) - Einl eitung @ 15\mod_1371721641099_21.docx @ 123714 @ @ 1

The I/O module 750-457 has 2 self-cleaning power jumper contacts that supply

and transmit power for the field side. The contacts on the left side of the I/O

module are designed as blade contacts and those on the right side as spring

contacts.

Pos: 31.3 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/A nsc hlüss e/L eist ung sko nta kte 2 LK ( Mess er/ Leis tu ngs kon takt e 2 LK ( Mes ser /Fe der ) - A bbildu ng, ein fach e Breite - S tand ard @ 15\ mod_1367500700037_21.doc x @ 118396 @ @ 1

Figure 3: Power Jumper Contacts

Pos: 31.4 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /Ans chl üs se/L eist u ngs kont akte 2 LK (M ess er/ Leis tung s konta kte 2 L K (M ess er/ Fed er) - Leg ende @ 15 \mod_1371721352500_21.docx @ 123710 @ @ 1

Table 5: Legend for Figure “Power Jumper Contacts”

Contact

Type

Function

Spring contact

Potential transmission (U

) for field supply

Spring contact

Potential transmission (0 V) for field supply

Blade contact

Potential feed-in (0 V) for field supply

Blade contact

Potential feed-in (U

) for field supply

Pos: 31.5 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- u nd sonsti ge Hin weis e/Acht ung/A chtu ng: Ma ximaler Strom L eistung skon takt e 10 A @ 3\mod_1226499143500_21.docx @ 25 029 @ @ 1

Do not exceed maximum current via power jumper contacts!

The maximum current to flow through the power jumper contacts is 10 A.

Greater currents can damage the contacts.

When configuring your system, ensure that this current is not exceeded. If

exceeded, insert an additional supply module.

Pos: 31.6 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- und s onsti g e Hin wei se/H in weis /Hi nw eis: Pot enti alei ns peis ekl emm e für Er de ei nsetz en! ( keine LK für Erd e) @ 3\ mod_1226499037468_21.doc x @ 25023 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 17

750-457 4AI ±10V DC S.E.

Manual

Version 1.2.0

Use supply modules for ground (earth)!

The I/O module has no power jumper contacts for receiving and transmitting the

earth potential. Use a supply module when an earth potential is needed for the

subsequent I/O modules.

Pos: 32 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1

18 Device Description WAGO-I/O-SYSTEM 750

750-457 4AI ±10V DC S.E.

Manual

Version 1.2.0

Pos: 33 /S erie 750 (WAGO-I/O-S YST EM) /Ger ät ebes chr ei bung /Ansc hl üss e/CA GE CLAM P- Anschl üss e - Ü ber schr ift 3 @ 6\ mod_1256296337770_21.doc x @ 43674 @ 3 @ 1

3.2.3 CAGE CLAMP

Connectors

Pos: 34 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsc hlüss e/A nalog ei nga ngs klem men/A nschlüsse 750-0453, -0 455, - 045 7 und -0459 @ 15\mod_1370335893038_21.doc x @ 121647 @ @ 1

Figure 4: CAGE CLAMP

Connectors

Table 6: Legend for Figure “CAGE CLAMP

Connectors”

Channel

Designation

Connector

Function

AI 1

Analog input1: Signal

Common

(ground)

Analog input: Common (ground)

AI 2

Analog input 2: Signal

Common

(ground)

Analog input: Common (ground)

AI 3

Analog input 3: Signal

Common

(ground)

Analog input: Common (ground)

AI 4

Analog input 4: Signal

Common

(ground)

Analog input: Common (ground)

Pos: 35 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Wicht ige Erl äuter unge n/Sich erh eits- und sons tig e Hi nw eis e/Hi nwei s/ Hin weis : Ge schi rmt e S ign all eitung en ver wen den! @ 7\ mod_1265723251019_21.doc x @ 50140 @ @ 1

Use shielded signal lines!

Only use shielded signal lines for analog signals and I/O modules which are

equipped with shield clamps. Only then can you ensure that the accuracy and

interference immunity specified for the respective I/O module can be achieved

even in the presence of interference acting on the signal cable.

Pos: 36 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 19

750-457 4AI ±10V DC S.E.

Manual

Version 1.2.0

Pos: 37 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/A nzei geel e ment e - Ü bersc hrift 2 @ 4\ mod_1240984390875_21.docx @ 31964 @ 2 @ 1

3.3 Display Elements

Pos: 38 /Serie 750 (WAGO-I/O-SYST EM)/ Ger ätebesc hrei bung/A nzei geele mente /Anal ogei ngang skle mmen/A nzei geele mente 7 50-04 57, - 0459 @ 15\mod_1370335605129_21.docx @ 121643 @ @ 1

Figure 5: Display Elements

Table 7: Legend for Figure “Display Elements”

Channel

Designation

LED

State

Function

1 Error AI 1 A

Off

Normal operation

Red

Excess/underflow

of the admissible measuring range

2 Error AI 2 C

Off

Normal operation

Red

Excess/underflow

of the admissible measuring range

3 Error AI 3 B

Off

Normal operation

Red

Excess/underflow

of the admissible measuring range

4 Error AI 4 D

Off

Normal operation

Red

Excess/underflow

of the admissible measuring range

Pos: 39 /Doku ment ation all gemei n/Gli eder ungsel eme nte/------Leerz eile------ @ 3\mod_1224662755687_0.doc x @ 24460 @ @ 1

Pos: 40 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/B edi enel eme nte - Üb ersc hrif t 2 @ 4 \mod_1239191655456_21.docx @ 30439 @ 2 @ 1

3.4 Operating Elements

Pos: 41 /Serie 750 (WAGO-I/O-SYST EM) /G erät eb esc hrei bung /Be die nel emen te/ Bedi en elem ent e B uskl em me 7 50- xxxx nicht vor hande n @ 4\mod_1236322031125_21.docx @ 28063 @ @ 1

The I/O module 750-457 has no operating elements.

Pos: 42 /Dokument ation al lge mein/G lieder ungs elem ente/---Sei te nwec hsel --- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

20 Device Description WAGO-I/O-SYSTEM 750

750-457 4AI ±10V DC S.E.

Manual

Version 1.2.0

Pos: 43 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/Sc he mati sch es S ch altbi ld - Über schr ift 2 @ 4\mod_1240984441312_21.docx @ 31967 @ 2 @ 1

3.5 Schematic Diagram

Pos: 44 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung /Sc he mati sche Sc hal tbil der/ Anal og eing ang skl em men/ Sc hemat isc hes Sc halt bild 75 0-0 457 @ 15\mod_1370254157081_21.doc x @ 121429 @ @ 1

Figure 6: Schematic Diagram

Pos: 45 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1

Page is loading ...