ABB i-bus KNX User manual

A

BB i-bus

®

KNX

DALI Gateway Emergency Lighting

DGN/S 1.16.1

Product Manual

ABB i-bus

®

KNX

Contents

DGN/S 1.16.1 | 2CDC 507 114 D0201 i

Contents

Page

1 General .................................................................................................3

1.1 Product and functional overview...................................................................................................4

1.2 DALI general.................................................................................................................................6

1.3 ABB i-bus

®

DALI-Gateway in comparison....................................................................................7

1.3.1 DGN/S 1.16.1 system description (group control) ........................................................................8

1.3.2 DGN/S 1.16.1 emergency lighting test .......................................................................................10

1.3.2.1 Function test...............................................................................................................................10

1.3.2.2 Duration test...............................................................................................................................10

1.3.2.3 Partial duration test.....................................................................................................................10

2 Device Technology............................................................................ 11

2.1 Technical data............................................................................................................................12

2.2 Circuit diagram ...........................................................................................................................14

2.3 Dimension drawing.....................................................................................................................15

2.4 Assembly and installation...........................................................................................................16

2.5 Description of the inputs and outputs .........................................................................................18

2.6 Manual operation........................................................................................................................19

2.6.1 Display elements........................................................................................................................20

3 Commissioning.................................................................................. 21

3.1 Overview ....................................................................................................................................22

3.1.1 Conversion of previous application program versions................................................................24

3.1.1.1 Procedure...................................................................................................................................25

3.2 Parameters.................................................................................................................................26

3.2.1 Parameter window General........................................................................................................27

3.2.2 Parameter window Central.........................................................................................................32

3.2.2.1 Parameter window - Emergency.................................................................................................39

3.2.2.2 Parameter window - Status ........................................................................................................42

3.2.2.3 Parameter window Gx Group.....................................................................................................51

3.2.2.4 Parameter window – Gx Status..................................................................................................60

3.2.2.5 Parameter window – Gx Fault....................................................................................................64

3.2.2.6 Parameter window – Gx Slave emergency.................................................................................68

3.2.2.7 Parameter window - Gx Slave....................................................................................................70

3.2.2.8 Parameter window - Gx Sequence.............................................................................................74

3.2.2.9 Parameter window - Gx Staircase lighting..................................................................................77

3.2.3 Parameter window Scenes.........................................................................................................84

3.2.4 Parameter window Scene x........................................................................................................85

3.2.5 Parameter window Sequence.....................................................................................................87

3.2.6 Parameter window Emergency Converter..................................................................................90

3.2.6.1 Parameter window Cx…Cy Converter........................................................................................92

3.2.6.2 Parameter window - Cx…Cy Test ..............................................................................................95

3.3 Communication objects..............................................................................................................98

3.3.1 Brief overview of the communication objects..............................................................................99

3.3.2 Communication objects General...............................................................................................101

3.3.3 Communication objects DALI output ........................................................................................102

3.3.4 Communication objects Group x...............................................................................................118

3.3.5 Communication objects Fault ...................................................................................................120

3.3.6 Communication objects Converter x.........................................................................................122

3.3.7 Communication objects Scene x/y............................................................................................124

3.3.8 Communication objects function Slave.....................................................................................126

3.3.9 Communication objects function Sequence..............................................................................127

3.3.10 Communication objects function Staircase lighting...................................................................128

4 Planning and Application................................................................129

4.1 Automatic DALI addressing......................................................................................................129

4.2 Function chart...........................................................................................................................130

4.3 Monitoring of lamps and ballasts..............................................................................................131

ABB i-bus

®

KNX

Contents

ii 2CDC 507 114 D0201 | DGN/S 1.16.1

4.4 Exchange of DALI devices....................................................................................................... 132

4.5 Burning-in of luminaries........................................................................................................... 133

4.6 Staircase lighting ..................................................................................................................... 134

4.7 Scene ...................................................................................................................................... 136

4.8 Slave........................................................................................................................................ 139

4.9 Sequence................................................................................................................................. 142

4.10 DALI lighting curve................................................................................................................... 147

4.10.1 Characteristic adjustment of the linear dimming curve ............................................................149

4.10.2 Characteristic adjustment with physical minimum dimming value............................................ 150

A Appendix...........................................................................................151

A.1 Code table Fault group/device (no. 20).................................................................................... 151

A.2 Code table 8 bit scene (no. 232).............................................................................................. 154

A.3 Code table Diagnostics byte “request“ (no. 25)........................................................................ 155

A.4 Code table Diagnostics byte “feedback“ (no. 25)..................................................................... 156

A.5 Further information about DALI................................................................................................ 158

A.6 Scope of delivery..................................................................................................................... 159

A.7 Ordering Information................................................................................................................ 160

A.8 DALI equipment....................................................................................................................... 161

A.9 Notes ....................................................................................................................................... 162

ABB i-bus

®

KNX

General

DGN/S 1.16.1 | 2CDC 507 114 D0201 3

1 General

This manual provides you with detailed technical information relating to the group-orientated ABB i-bus

®

KNX DALI Gateway with Emergency Lighting Function DGN/S 1.16.1. The installation, programming and

commissioning and the device are described using examples. Furthermore, basic terminology used with

emergency lighting technology is explained.

The DGN/S is used for control of DALI equipment, e.g. ballasts, transformers or LED converters with DALI

interfaces compliant to EN 62386 via KNX. Furthermore, DALI self-contained emergency lighting (device

type 1) with individual batteries can be integrated to EN 62386-202.

Here the DGN/S 1.16.1 itself does not offer a functionality in terms of the emergency lighting regulations,

e.g. protocoling functions or other associated stipulated functions. It serves as an intelligent mediator be-

tween KNX and DALI.

The different mandatory tests for emergency lighting, e.g. functional tests or duration testing, can be trig-

gered via KNX, and the result can be provided again on the KNX via communication objects.

The DGN/S combines both the internationally standardized and open standards in the digital illumination

control DALI (EN 62386) and intelligent installation system KNX (ISO/IEC 14543-3 and EN 50090).

ABB i-bus

®

KNX

General

4 2CDC 507 114 D0201 | DGN/S 1.16.1

1.1 Product and functional overview

The group-orientated KNX DALI Gateway DGN/S 1.16.1 is a modular installation device in ProM design.

Up to 64 DALI devices can be connected to a DALI output. These 64 DALI devices can be divided into up

to 16 lighting groups. Every lighting group can be independently switched, dimmed and a brightness value

can be set via the KNX. For each group, a KNX communication object is available for indicating a lamp,

ballast or the combination of lamp and ballast fault on the KNX. The fault status of an individual device can

also be signalled or queried via coded communication objects. Furthermore, the functions Scene (up to

14), Staircase lighting, Slave and Sequence are available.

The special feature of the DGN/S 1.16.1 is that DALI emergency lighting converters can also be connected

as DALI devices. A DALI emergency lighting converter is a DALI device, which monitors and tests the sta-

te of an individual battery of an emergency lighting device and that provides the information via standard-

ized DALI telegrams compliant to EN 62 386-202. The DALI Gateway with Emergency Lighting Function

DGN/S 1.16.1 evaluates this information and sends it on the KNX.

A self-contained emergency lighting can have

x two DALI devices (ballast and emergency lighting converter) or

x one DALI device, which features the function of the emergency lighting converter and the control of

the lighting equipment, usually LEDs.

In the first case, the DGN/S 1.16.1 controls a maximum of 32 emergency lights, as the DALI standard lim-

its the number of DALI devices to 64 DALI devices. In the second case, DALI emergency lighting convert-

ers with two functions as a DALI device can connect up to 64 emergency lights to the DGN/S.

Access to the individual devices for the determined individual functionalities is possible. In the case of mo-

nitoring of individual lamps or batteries, the information is available as coded KNX telegrams that are up to

4 bytes in length.

The DGN/S 1.16.1 does not support overlapping DALI lighting groups. Cross-lighting groups should be

formed by KNX group addressing. Furthermore, it is possible to commonly control all DALI devices con-

nected to a DALI output via DALI output telegrams (DALI broadcast control).

The DALI power supply for the 64 DALI devices is integrated into the DGN/S 1.16.1.

Readdressing of the DALI devices and the assignment of the 64 DALI devices into 16 lighting groups is

implemented in an ETS independent DALI-Software-Tool, so that for example, a facility manager without

ETS knowledge is capable of exchanging and reassigning DALI devices, should maintenance be required.

Furthermore, the error states of the individual DALI devices and/or lighting groups are represented graphi-

cally with the DALI-Software-Tool.

The setting of the parameters and allocation of the group addresses is implemented primarily with the En-

gineering Tool Software ETS. The most up-to-date version should be used. The minimum requirement is

version ETS2 V1.3.

ABB i-bus

®

KNX

General

DGN/S 1.16.1 | 2CDC 507 114 D0201 5

The application program offers a range of functions:

x Switching, dimming, setting of brightness values

x Status feedbacks via common or separate communication objects

x Status response of a lamp and/or ballast malfunction

x Programming of individual maximum and minimum dimming limit values (dimming thresholds)

x Different dimming speeds for switching, setting brightness values and dimming

x Reaction at DALI and KNX voltage failure and recovery

x Programming of the brightness value (power ON level) after a ballast operating voltage recovery

x KNX control of all connected DALI devices without prior commissioning (DALI group assignment)

x Triggering of the emergency lighting test via a DALI emergency lighting converter

x Function test

x Duration test

x Partial duration test

x Battery charge state

x Transfer of the emergency lighting test results to the KNX

Various operating modes, e.g.:

x Function Slave for integration of the lighting groups in an energy efficient lighting control

x 14 independent light scenes, which can be recalled or stored via 1 bit or 8 bit telegrams

x Function Staircase lighting including pre-warning

x Function Sequence for programming of running lights or colour effects

ABB i-bus

®

KNX

General

6 2CDC 507 114 D0201 | DGN/S 1.16.1

1.2 DALI general

The requirements for modern lighting technology are extremely varied. While previously lighting was only

required for visual tasks, nowadays factors such as comfort, ambience, functionality and energy efficiency

are in the foreground. Furthermore, a modern lighting system is increasingly being incorporated into the

facility management of the building installation in order to monitor the status of the entire lighting system.

Often, a complex lighting management system is needed, which meets the uses of the premises. All these

requirements are either not adequately met by the traditional 1–10 V electrical installation or only with con-

siderable effort and cost. The DALI standard (EN 60929 previously EN 62386) has emerged against this

background in conjunction with leading manufacturers of lamp ballasts. It describes and defines the digital

interface DALI (Digital Addressable Lighting Interface) for lighting technology equipment.

DALI has become established as an independent standard in the field of lighting technology. The range of

ballasts, transformers, dimmers and relays with DALI interfaces has decisively influenced modern lighting

technology.

Part 202 of DALI standard 62386 described DALI commands to communicate with emergency converters.

With this DALI commands emergency test (e.g. function test, duration test, and battery capacity informa-

tion) can be triggered. The test result will send back from the emergency converter to DALI and over the

DGN/S to KNX.

This KNX DALI technique allows a management building system to trigger the demanded emergency tests

and documented the test results.

More detailed information concerning the DALI can be found in the manuals DALI Gateway DGN/S 1.16.1, The DALI

Manual or the DALI, Manual of DALI AG, which is part of the ZVEI.

ABB i-bus

®

KNX

General

DGN/S 1.16.1 | 2CDC 507 114 D0201 7

1.3 ABB i-bus

®

DALI-Gateway in comparison

ABB Stotz Kontakt GmbH currently has different KNX DALI-Gateway devices in the ABB i-bus

®

range, for

integration of DALI interfaces into a KNX building installation. Every DALI Gateway has benefits that can

be specifically utilised on different project types.

These differences are described in the following.

The differences are listed briefly below in the table. A detailed description can be found in the chapters that

follow.

Property

DG/S 8.1

Control

Central

DG/S 1.1

Control

Individual

DG/S 1.16.1

Control

Group

DGN/S 1.16.1

Control

Group

Design MDRC MDRC MDRC MDRC

Mounting width 6 4 4 4

DALI outputs 8 (A…H) 2 (A & B) 1 (A) 1 (A)

DALI device (ballast)

per Gateway

128 (max.16

per output)

128 (max. 64

per output)

64

(ballasts and

emergency lighting

converter)

DALI emergency lighting converter - - - 64

Lighting groups per Gateway 8 (installation)

A:

max. 255 (KNX)

B: 1

16

*)

(DALI) 16 (DALI)

Lighting groups

established via

cable installation

A: KNX

B: cable installation

DALI DALI

DALI devices (e.g. ballasts) per

lighting group

max. 16

A: max. 64

B: max. 64

Max. 64 Max. 64

DALI addressing not required

A: 64 individual

B: 64 individual

64 individual 64 individual

Number of DALI telegrams per KNX

telegram of the group

1 telegram

A: max. 64 telegrams

B: 1 telegram

1 telegram

per group

1 telegram

per group

Power supply to the KNX processor via KNX KNX KNX KNX

DALI voltage

integrated

power supply

integrated

power supply

integrated

power supply

integrated

power supply

*) The 16th lighting group can also be used internally as an option. The DGN/S 1.16.1 assigns the DALI devices, that do not

belong to any other lighting group, to group 16. In this way, commissioning of all devices using the KNX via the communi-

cation objects DALI output is also possible without prior group assignment.

ABB i-bus

®

KNX

General

8 2CDC 507 114 D0201 | DGN/S 1.16.1

1.3.1 DGN/S 1.16.1 system description (group control)

The KNX/DALI Gateway DGN/S 1.16.1 with emergency lighting function is primarily a “normal” DALI Ga-

teway with group control. However, additional DALI devices for self-contained emergency lighting (device

type 1) with individual batteries compliant to the DALI standard EN 62386-202 are supported. Up to 64

DALI devices can be connected to a DALI output. DALI emergency lighting devices and normal DALI de-

vices can be combined as required. An emergency light can consist of two separate DALI devices or also

of just one individual device:

x Two separate DALI devices:

1 ballast (DALI device 1) for normal lighting. It assumes the control of the lighting equipment in normal

operation.

1 emergency lighting converter (DALI device 2), which controls the lighting equipment in emergency

lighting operation. Generally, the emergency lighting converter disconnects the normal ballast in

emergency lighting operation and autonomously assumes control of the emergency lighting. The

emergency lighting converter will switch back to the normal ballast only after emergency lighting op-

eration has ended.

x One DALI device:

1 combined emergency lighting converter, which assumes the control of the lighting equipment in

normal and in emergency lighting operation. Usually, they are LED based solutions.

If battery-operated emergency lighting contains two DALI devices (a ballast and a converter, each with a

DALI interface), up to 32 battery operated emergency lights can be connected. The DALI Gateway auto-

matically recognizes whether the connected DALI device is a battery operated emergency converter and

thus an emergency lighting device (device type 1) compliant to EN 62386-202. This information is indi-

cated by the DALI-Software-Tool. It is possible that both “normal” lamps as well as battery operated emer-

gency lighting are connected in a mixed configuration to the DGN/S 1.16.1. However, the maximum per-

mitted number of 64 DALI devices may not be exceeded.

Self tests of every individual emergency lighting converter is started by request via the KNX. The test re-

sult is reported via the KNX. The communication object Emergency test trigger starts the emergency light-

ing test (function test, short duration test or duration test) or queries emergency lighting tests already un-

der way. The test result is automatically sent via the 4 byte communication object Emergency test result.

Via the communication object Slave emergency active/status, all the lamps in a group controlled by the

DGN/S to the parameterized Brightness value are set. This is independent of whether the lamps them-

selves are affected by an emergency lighting operating voltage failure, mains voltage failure or DALI volt-

age failure. The response during the emergency lighting operation activated by the DALI Gateway can be

parameterized. The prerequisite is that the DGN/S is supplied by the DALI operating voltage.

The Slave emergency is not tripped by a voltage failure. It is triggered by DGN/S if a parameterised num-

ber of lamp or ballast failures exist.

Note

During emergency lighting operation, the DALI devices cannot be commissioned.

ABB i-bus

®

KNX

General

DGN/S 1.16.1 | 2CDC 507 114 D0201 9

The following diagram illustrates the function of the group-orientated DGN/S 1.16.1.

Output A

...

1

3

2

16

KNX

Ballast

Con-

verter

Con-

verter

Ballast Ballast

Ballast

Con-

verter

Ballast

Con-

verter

1

2

3

4

64

DALI-Gateway

Emergency

Lighting

DGN/S 1.16.1

...

ABB i-bus

®

KNX

General

10 2CDC 507 114 D0201 | DGN/S 1.16.1

1.3.2 DGN/S 1.16.1 emergency lighting test

The DGN/S 1.16.1 serves as a gateway for self-contained emergency lighting systems and KNX building

management. On this way it is possible to controlled and monitored DALI-based emergency self-contained

lighting devices (converters) compliant with IEC 62 386-202.

A DALI device to IEC 62 386-202 (Device type 1), for self-contained emergency lighting with individual bat-

teries, is described in this manual in shortened form as an emergency lighting converter.

The DGN/S 1.16.1 itself does not offer functionality in terms of the emergency lighting regulations, e.g.

protocoling functions or other associated stipulated functions. It is used exclusively as a gateway between

the KNX communication objects and the DALI commands.

The different mandatory tests for emergency lighting are controlled by KNX communication objects. The

test sequence is subsequently monitored by KNX communication objects, and the results are signalled by

further communication objects on the KNX.

A further possibility is the use of an automated test interval that is controlled by the DALI emergency light-

ing converter itself. The interval duration is determined by the KNX parameter. KNX communication ob-

jects transfer the results.

1.3.2.1 Function test

The function test is undertaken by the emergency lighting converter itself. The function test is requested at

a parameterizable interval in the emergency lighting converter or by a KNX communication object. The

functional security of the emergency lighting converter electronics and correct operation of a lamp and a

switch-over device for an individual battery are tested.

1.3.2.2 Duration test

The duration test is implemented on the basis of the IEC 62 386-202 and is used to determine whether the

individual battery of the system is within the limits of the rated operating duration in emergency lighting op-

eration.

1.3.2.3 Partial duration test

The partial duration test is controlled with the aid of the duration test of the DALI device by the Gateway.

This is possible as a partial duration test is not stipulated or described by the standards. It simply offers an

additional and enhanced possibility for operation readiness of emergency lighting in a simple and time-

efficient way without completely discharging the battery.

ABB i-bus

®

KNX

Device Technology

DGN/S 1.16.1 | 2CDC 507 114 D0201 11

2 Device Technology

The KNX ABB i-bus

®

DALI Gateway with

Emergency Lighting Function DGN/S

1.16.1 is a KNX- modular installation

device (MDRC) in Pro M-design for

installation in the distribution board on

35 mm mounting rails.

The DGN/S integrates operating devices

with DALI interfaces to EN 62386 into a

KNX building installation. The connection

to the ABB i-bus

®

is implemented via a

KNX connection terminal on the device

shoulders.

The DALI output of the DGN/S can be

used to connect up to 64 DALI devices. It

can also exclusively contain 64 DALI

devices for self-contained emergency

lighting compliant to EN 6286-202. Both

“normal” lamps as well as battery oper-

ated emergency lighting can be con-

nected in a mixed configuration to the

DGN/S 1.16.1.

Control of the lamps via KNX is under-

taken by 16 lighting groups, which can be

comprised of any 64 DALI devices.

An individual project-related DALI device

group assignment is possible using the

DALI-Software-Tool.

The fault status (lamps, ballasts or

emergency light converter) of every

individual DALI device or of the lighting

group is sent via different KNX commu-

nication objects on the KNX.

In addition to the standard functions, e.g.

switching, dimming and brightness value

setting with the corresponding feed-

backs, the DGN/S has the functions

Staircase lighting, Scene, Sequence and

Slave. The lighting groups can be

integrated in this way into a constant

lighting control.

Function, duration and partial duration

tests and battery tests for the emergency

lighting systems with individual batteries

to EN 62386-202 can be triggered and

stopped via KNX. The test results are

made available on the KNX.

All DALI devices can be controlled

together in KNX mode as well as manual

mode.

The DGN/S is a DALI control device

(master) and requires an AC or DC

auxiliary power supply. A separate DALI

power supply is not required. The DALI

power source for the 64 DALI devices is

integrated into the DGN/S.

2CDC 071 009 S0011

ABB i-bus

®

KNX

Device Technology

12 2CDC 507 114 D0201 | DGN/S 1.16.1

2.1 Technical data

Supply

gateway operating voltage 85…265 V AC, 50/60 Hz

110…240 V DC

power consumption total via mains maximum 8 W at 230 V AC and max. load

current consumption total via mains maximum 35 mA at 230 V AC and max. load

leakage loss total for device maximum 3 W at 230 V AC and max. load

current consumption KNX maximum 10 mA

power consumption via KNX maximum 210 mW

DALI outputs (channels):

number of outputs 1 x 64 DALI device (16 lighting groups)

number of DALI devices

maximum 64 to EN 62 386; DALI devices for

self-contained emergency lighting to EN 62 386-

202 are supported.

2)

distance between DGN/S and last DALI device

cable cross-section 0.5 mm

2

0.75 mm

2

1.0 mm

2

1.5 mm

2

100 m

1)

150 m

1)

200 m

1)

300 m

1)

Connections

KNX KNX connection terminal,

0.8 mm Ø, single core

DALI outputs and

mains voltage

screw terminal

0.2…2.5 mm

2

stranded

0.2…4 mm

2

single core

tightening torque maximum 0.6 Nm

Operating and display elements

button

DALI output test

button/LED

for assignment of the physical address

LED

, green

display for operation readiness

LED

, yellow for displaying DALI fault, constant light

for displaying test mode, slow flashing

for displaying initialisation or more than 64 DALI

devices, quick flashing

Enclosure

IP 20 to EN 60529

Safety class

II to EN 61140

Isolation category

overvoltage category

pollution degree

III to EN 60 664-1

2 to EN 60664-1

KNX safety extra low voltage

SELV 24 V DC

DALI voltage

typical 16 V DC (9.5…22.5 V DC)

no-load voltage

lowest supply current at 11.5 V

highest supply current

to EN 60929 and EN 62386

16 V DC

160 mA

230 mA

ABB i-bus

®

KNX

Device Technology

DGN/S 1.16.1 | 2CDC 507 114 D0201 13

Temperature range

operation -5 °C…+45 °C

storage -25 °C…+55 °C

transport -25 °C…+70 °C

Environmental conditions

humidity

maximum 93 %, moisture condensation should

be excluded

Design

modular installation device (MDRC) modular installation device, ProM

dimensions 90 x 72 x 64.5 mm (H x W x D)

mounting width 4 modules at 18 mm

mounting depth 68 mm

Installation

on 35 mm mounting rail to EN 60 715

Mounting position

as required

Weight

0.16 kg

Housing, colour

plastic housing, grey

Approvals

KNX to EN 50 090-1, -2 certification

CE mark in accordance with the EMC guideline and low

voltage guideline

1)

The length relates to the common DALI control cable. The maximum values are rounded off and relate to the resistance values. EMC influences

are not considered. For this reason, the values should be considered as absolute maximum values.

2)

Both “normal” lamps as well as battery operated emergency lighting can be connected in a mixed configuration to the DGN/S 1.16.1. However, the

maximum number of DALI devices may not exceed 64.

Device type Application program Maximum number of

communication objects

Maximum number of

group addresses

Maximum number of

associations

DGN/S 1.16.1 Switch Dim Emergency 1f

DALI/…*

246 254 255

* … = current version number of the application program. Please observe the software information on our homepage for this purpose.

Note

The DGN/S is compliant to the SELV characteristics to IEC 60 364-4-41 (VDE 0100-410).

DALI does not need to feature SELV properties, and it is possible to route the DALI control lines to-

gether with the mains voltage on a multi-core cable.

Note

The ETS and the current version of the device application program are required for programming.

The current version of the application program is available for download on the internet at

www.abb.com/knx. After import in the ETS, it is available in the ETS under ABB//Lighting/ DALI/ Switch

Dim Emergency 1f DALI.

The device does not support the closing function of a KNX device in the ETS. If you inhibit access to all

devices of the project with a BCU code, it has no effect on this device. Reading out data and program-

ming is still possible.

ABB i-bus

®

KNX

Device Technology

14 2CDC 507 114 D0201 | DGN/S 1.16.1

2.2 Circuit diagram

DGN/S 1.16.1

1 Label carrier

2 Button

(KNX)

3 LED

, red (KNX)

4 Connection terminal (KNX)

5 LED

, yellow (DALI fault)

6 LED

, green (Gateway ON)

7 Gateway operating voltage

8 Output (DALI)

9 Button

(DALI)

10 DALI device, without/with function self-contained emergency lighting

2CDC 072 012 F0011

ABB i-bus

®

KNX

Device Technology

DGN/S 1.16.1 | 2CDC 507 114 D0201 15

2.3 Dimension drawing

DGN/S 1.16.1

2CDC 072 014 F0011

ABB i-bus

®

KNX

Device Technology

16 2CDC 507 114 D0201 | DGN/S 1.16.1

2.4 Assembly and installation

The device is a modular installation device for quick installation in the distribution board on 35 mm mount-

ing rails to EN 60 715. The mounting position can be selected as required.

The electrical connection is implemented using screw terminals. The connection to the KNX is imple-

mented using the supplied KNX connection terminal. The terminal assignment is located on the housing.

The device is ready for operation after connection to the KNX voltage and the gateway operating voltage.

Accessibility of the devices for the purpose of operation, testing, visual inspection, maintenance and repair

must be provided compliant to VDE 0100-520.

Commissioning requirements

In order to commission the device, a PC with ETS and a KNX interface, e.g. USB or IP, are required. The

device is ready to operate when the KNX voltage and the gateway operating voltage are applied.

The assignment of the DALI devices to the lighting groups as well as the configuration of the emergency

lighting converter is undertaken with the DALI-Software-Tool.

The emergency lighting battery must be charged for commissioning of the DALI emergency lighting con-

verter. Commissioning without emergency lighting operation is not possible.

Important

Acceptance of the emergency lighting monitoring must be discussed with the corresponding approval

agency.

The installation and commissioning may only be carried out by qualified electrical specialists. The appro-

priate norms, guidelines, regulations and specifications for your country should be observed when plan-

ning and setting up electrical installations and security systems for intrusion and fire detection.

Protect the device from damp, dirt and damage during transport, storage and operation.

Only operate the device within the specified technical data limits!

The device should only be operated in an enclosed housing (distribution board)!

The voltage supply to the device must be switched off, before mounting work is performed.

Manual operation

The device incorporates manual operating features. The device features a button

for manual switching

of the DALI output.

ABB i-bus

®

KNX

Device Technology

DGN/S 1.16.1 | 2CDC 507 114 D0201 17

Supplied state

The device is supplied with the physical address 15.15.255. The application program is preloaded. It is

therefore only necessary to load group addresses and parameters during commissioning.

However, the complete application program can be reloaded if required. A longer downtime may result if

the application program is changed or after a discharge.

Assignment of the physical address

The assignment and programming of the physical address is carried out in the ETS.

The device features a

button for assignment of the physical device address. The red LED lights up,

after the button has been pushed. It switches off as soon as the ETS has assigned the physical address or

the

button is pressed again.

Download response

Depending on the PC, which is used, the progress bar for the download may take up to one and a half mi-

nutes, before it appears, due to the complexity of the device.

Cleaning

If devices become dirty, they can be cleaned using a dry cloth or a cloth dampened with a soapy solution.

Corrosive agents or solutions should never be used.

Maintenance

The device is maintenance-free. No repairs should be carried out by unauthorised personnel if damage

occurs, e.g. during transport and/or storage.

ABB i-bus

®

KNX

Device Technology

18 2CDC 507 114 D0201 | DGN/S 1.16.1

2.5 Description of the inputs and outputs

On the DALI output up to 64 devices can be connected with a DALI interface. The DGN/S is a DALI master

with integrated DALI power supply.

Important

Other DALI masters may not be connected to the output of the DGN/S.

The connection of another master to the single master system can cause communication malfunctions.

Caution

Other DALI power supplies may not be connected to the output of the DGN/S.

The connection of further DALI supply voltages may destroy the DGN/S due to voltage summation.

Connection of 230 V mains voltage to the DALI output will destroy the DALI end stage and the DALI

output.

A control line on the DALI output with the following maximum length can be used:

Cable length [mm

2

]

2 x 0.5 2 x 0.75 2 x 1.0 2 x 1.5

Max. cable length [m] from the DGN/S to DALI device

100 150 200 300

These values are rounded off and relate to the resistance values. EMC influences are not considered. For

this reason, the values should be considered as absolute maximum values.

It is possible to assemble the DALI control cable with conventional installation material for mains cables.

The two cores of the five-core NYM 5 x 1.5 mm

2

, which are not required, can be used without considera-

tion of the polarity. It is not mandatory to lay a separate control cable.

The isolation between DALI control cables and the power supply is assured by the simple insulation prop-

erties according to EN 410. SELV properties are not featured.

The device is ready for operation after connection of the gateway operating voltage. The green operating

LED on the front of the device lights up.

The yellow flashing (10 Hz) DALI LED indicates the maximum 90 second initialisation phase of the DGN/S.

The DALI system environment is analysed in this phase. If required, new DALI devices are allocated a

DALI address and can be assigned to a lighting group with the DALI-Software-Tool, whereby the lamps

are integrated into the KNX building automation. During this phase, it cannot be guaranteed that an incom-

ing telegram will be processed.

Note

The initialisation phase will not end if more than 64 DALI devices are connected.

The initialisation phase starts automatically after download, gateway operating voltage recovery and KNX

voltage recovery.

The initialisation phase is undertaken if in the parameterization Enable automatic DALI addressing has be-

en deactivated.

Page is loading ...

ABB i-bus KNX User manual

Related papers

Other documents