Motorola 68230 - Vanguard 300 DSU/CSU User manual

Vanguard 300/305 Operator's Guide

Notice

1995 Motorola Inc.

20 Cabot Boulevard

Mansfield, Massachusetts 02048

(508) 261-4000

Printed in U.S.A.

Restricted Rights Notification for U.S. Government Users

The software (including firmware) addressed in this manual is provided to the

U.S. Government under agreement which grants the government the minimum

"restricted rights" in the software, as defined in the Federal Acquisition

Regulation (FAR) or the Defense Federal Acquisition Regulation Supplement

(DFARS), whichever is applicable.

If the software is procured for use by the Department of Defense, the following

legend applies:

Restricted Rights Legend

Use, duplication, or disclosure by the Government is subject to restrictions as set

forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer

Software clause at DFARS 252.227-7013.

If the software is procured for use by any U.S. Government entity other than the

Department of Defense, the following notice applies:

Notice

Notwithstanding any other lease or license agreement that may pertain to, or

accompany the delivery of, this computer software, the rights of the Government

regarding its use, reproduction, and disclosure as set forth in FAR 52.227-19(C).

Unpublished - rights reserved under the copyright laws of the United States.

Proprietary Material

Information and software in this document are proprietary to Motorola Inc. (or its

Suppliers) and without the express prior permission of an officer of Motorola Inc.,

may not be copied, reproduced, disclosed to others, published, or used, in whole

or in part, for any purpose other than that for which it is being made available.

Use of software described in this document is subject to the terms and conditions

of the Motorola Software License Agreement.

This document is for information purposes only and is subject to change without

notice.

Vanguard 300/305 Radio Frequency Interference Regulations

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules, CISPR 22 and EN 55022.

These limits are designed to provide reasonable protection against interference in

a residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician to help.

Changes or modifications not expressly approved by Motorola could void the

user's authority to operate the equipment.

This Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

This product was FCC certified under test conditions that included use of shielded

data terminal equipment cables. Use of different cables will invalidate FCC

certification and increase the risk of causing interference to radio and TV

reception.

You can obtain the proper cables from Motorola.

Writer: Donna McLean

Project Editor: Susan L. Roswit

Publication Specialist: Paul Tavares

Illustrator: Tim Kinch

Part No.: 09965, Rev B

Publication Code: RC

First Printing: Aug. 1995

Manual is current for Release 4.50 of the Vanguard 300 operating software, and

Release 4.49 of the Vanguard 305 operating software.

To comment on this manual, please send email to: [email protected] or use the

Customer Response Card located in this manual.

Internet Information

Additional company and product information can be found on our Internet Web

page at:

http://www.mot.com/MIMS/ISG/

About This Manual

Introduction

This manual describes features, hardware, specifications, and applications for the

Motorola Vanguard 300 and Vanguard 305 Frame Relay Access Devices

(FRADs).

For information on operating system software and configuration see the 6500

Series Documentation Kit, which includes the 6500 Series Introduction Manual

and the 6500 Series Configuration and Administration Manual.

Audience

This manual is intended for operators of the Motorola Vanguard 300/305 FRAD.

Software Revision Level

The Vanguard 300 runs Release 4.33 or higher releases of operating software. The

Vanguard 305 runs Release 4.49 or higher.

Special Notices

The following notices emphasize certain information in the manual. Each serves a

special purpose and is displayed in the format shown:

IMPORTANT: Important is used to emphasize any significant procedural information.

Caution provides you with information that, if not followed, can result in

damage to software, hardware, or data.

Warning is the most serious notice, indicating that you can be physically hurt.

How to Use This Manual

The following table describes the contents of this guide.

This chapter... Describes

Chapter 1 Vanguard 300/305 hardware and software features, and FCC

Part 68 guidelines and Telephone Company procedures.

Chapter 2 Setting up a Vanguard 300/305, including site preparation,

how to unpack the unit, installation procedures, powerup and

diagnostic procedures, and how to connect to the Control

Terminal Port

Chapter 3 Vanguard 300/305 applications and configuration

information, including step-by-step configuration sequences

Chapter 4 Maintaining the Vanguard 300/305, including replacing

option cards and troubleshooting information

Related Documentation

The following documentation is not provided with the Motorola Vanguard

300/305; it can be ordered separately. You should familiarize yourself with the

6500 Series documentation before you use the Vanguard Series.

To acquire any of these sets of documentation, refer to the following product

codes:

Product Code Documentation Kit Includes:

17460 6500 Series Documentation

Kit

The printed documentation

set including:

6500 Series Introduction

Manual (Part No. 09871,

Rev D)

6500 Series Configuration

and Administration Manual

(Part No. 09873, Rev D)

6500 Installation Manual

(Part No. 09872, Rev E)

6520 Installation Manual

(Part No. 09901, Rev C)

17461 Documentation Change

Notices

Documentation for all

software releases since the

last printing of the main

documentation set.

17313 Multi-Product CD-ROM All 6500 Series

documentation and some

Vanguard user

documentation, as was

available at the time of

release.

6500 Series documentation is prepared using FrameMaker document publishing

software.

Additional Related Documentation

The following documents contain information related to the installation and

operation of 65xx and Vanguard platforms:

• The 6500 Series Options and Protocols Binder (Part No. 09950)

Vanguard Operator's Guides

• Vanguard 100 Operator's Guide (Part No. 09962, Rev A)

• Vanguard 200 Operator's Guide (Part No. 09968, Rev A)

• Vanguard 300/305 Operator's Guide (Part No. 09965, Rev B)

Software Download Guides

• 6520 Software Download Guide (Part No. 09901-6, Rev A)

• 6500 PLUS Software Download Guide (Part No. 09872-2, Rev A)

• Vanguard 100 Software Download Guide (Part No. 09962-2, Rev A)

• Vanguard 200 Software Download Guide (Part No. 09968-1, Rev A)

• Vanguard 300/305 Software Download Guide (Part No. 09965-1, Rev B)

Trademarks

The following are trademarks or registered trademarks of their respective

companies or organizations.

DECconnect Digital Equipment Corporation

About the Vanguard 300/305

Overview

The Vanguard 300/305

The Motorola Vanguard 300/305 Frame Relay Access Device (FRAD) provides

serial devices with LAN Ethernet (Vanguard 300) or Token Ring (Vanguard 305)

access into public or private Frame Relay networks.

The FLASH-based Vanguard 300/305 is available in FRAD, mono FRAD, or duo

FRAD configurations with either two or three serial ports and an abundant list of

protocol choices. You can order the base unit with an integral DSU and a software

application package, making this low-cost FRAD an economical choice for

connecting remote LAN sites with both LAN and Serial traffic to public Frame

Relay services.

You can also configure extra serial ports on the mono and duo FRAD to provide a

backup link to the Frame Relay network port. Or, you can connect them to an

external analog dial modem, SW56 DSU or ISDN BRI TA, to provide an

alternate path in case of network failure.

Example of the Vanguard 300/305

The Vanguard 300/305 is available either with or without an integral DSU

daughtercard or DIM Site daughtercard in a desktop-size standalone enclosure, as

shown in Figure 1-1.

Figure 1-1. The Vanguard 300 and Vanguard 305

Features

Introduction

This section describes Vanguard 300/305 hardware configurations and standard

features.

Configurations Options

The Vanguard 300/305 is available in the following hardware configurations.

This configuration: Offers...

300 Ethernet FRAD Ethernet port, V.24 port, CTP port.

300 Ethernet FRAD with

DSU

Ethernet port, DSU daughtercard in Port 1, CTP

port.

300 Ethernet mono

FRAD

Ethernet port, serial port with a choice of DIM port

interface (V.24, V.35, V.36, or V.11) in Port 2, CTP

port.

300 Ethernet mono

FRAD with DSU

Ethernet port, V.24 port, DSU daughtercard in Port

1, CTP port.

300 Ethernet duo FRAD Ethernet port, V.24 port, DIM Site daughtercard in

Port 1 with choice of DIM port interface (V.24,

V.35, V.36, or V.11), CTP port.

300 Ethernet duo FRAD

with DSU

Ethernet port, V.24 port, DSU daughtercard in Port

1, serial port with a choice of DIM port interface

(V.24, V.35, V.36, or V.11) in Port 2, CTP port.

305 Token Ring FRAD Token Ring port, V.24 port, CTP port.

305 Token Ring FRAD

with DSU

Token Ring port, DSU daughtercard in Port 1, CTP

port.

305 Token Ring mono

FRAD

Token Ring port, serial port with a choice of DIM

port interface (V.24, V.35, V.36, or V.11) in Port 2,

CTP port.

305 Token Ring mono

FRAD with DSU

Token Ring port, V.24 port, DSU daughtercard in

Port 1, CTP port.

305 Token Ring duo

FRAD

Token Ring port, V.24 port, DIM Site daughtercard

in Port 1 with a choice of DIM port interface (V.24,

V.35, V.36, or V.11), CTP port.

305 Token Ring duo

FRAD with DSU

Token Ring port, V.24 port, DSU daughtercard in

Port 1, serial port with a choice of DIM port

interface (V.24, V.35, V.36, or V.11) in Port 2, CTP

port.

Standard Features

The Vanguard 300/305 features 1, 2, or 3 port Serial FRAD functionality with

LAN access to Frame Relay networks.

All Vanguard 300/305 base units provide the following:

• Control Terminal Port (CTP) for configuration and management

• Dual link ability

• Optional DSU

• Optional ISDN Daughtercards

• Ethernet (Vanguard 300) or Token Ring (Vanguard 305) interface

• Frame Relay and X.25 service

• X.25 PAD support

• Multiprotocol support

• SNMP management

• Software download through Trivial File Transfer Protocol (TFTP)

• Fully compatible with 6500 PLUS and 6520.

• RFC 877 encapsulation

CTP Port

Port 3 on the Vanguard 300/305 can be used as a CTP for configuration,

reporting, and troubleshooting. You can default Port 3 for CTP access from the

front panel of the Vanguard. See "Connecting to the CTP" in Chapter 2 for more

details.

DSU Functionality

The DSU daughtercard functionality suits an extended range of 56 kbps point-to-

point DDS1 interface that conforms to AT&T 62310 or ANSI T1E1.4/91-006.

The DSU is FCC Part 68 registered.

Diagnostic loopbacks from the telephone company are supported; local

diagnostics are activated from the CTP.

LAN Support

The Vanguard 300 features an onboard Ethernet interface that supports both

10BaseT and AUI. The factory default is AUI.

The Vanguard 305 features an onboard Token Ring interface. Support includes:

• 4 and 16 Mbps support

• Type 1 STP (DB-9)

• Type 3 UTP (RJ-45)

Frame Relay & X.25 Service

The Vanguard 300/305 provides serial devices with economical LAN access into

public or private Frame Relay WAN networks via Ethernet or Token Ring.

Because the Vanguard 300/305 also supports X.25, you can configure it as a PAD

if Frame Relay is not an immediate need. When Frame Relay service becomes

available, you can reconfigure the Vanguard 300/305 as a FRAD.

Multiprotocol Support

Support includes SDLC, Bisync, X.25, Async, IP/IPX, and Routing and Bridging,

as well as many other serial protocols.

Software Download

Trivial File Transfer Protocol (TFTP) provides software downloading for network

software and device configuration software.

RFC 877

RFC 877 encapsulation of IP datagrams over an X.25 network allows for

interoperability of Front End Processors (FEPs) that support X.25 and IP traffic as

well as router vendors supporting RFC 877/1356.

Sample Applications

Figure 1-2 shows sample applications for the Vanguard 300/305.

Figure 1-2. Vanguard 300/305 Sample Applications

Hardware

Introduction

This section describes the Vanguard 300/305 hardware components.

See the Software Release Notice (SRN) accompanying your Vanguard product for

details on hardware platform bundles currently available.

Components

Vanguard 300/305 base units include the following components:

• A motherboard

• A power supply

• One V.24 port with DB25 connector

• Optional port for daughtercard (DIM Site or DSU)

• Optional DIM port on the motherboard

• One LAN port:

§ Vanguard 300: Ethernet with either 10BaseT or AUI interface

§ Vanguard 305: Token Ring with connectors for both shielded

(STP) and unshielded

• (UTP) cables

• One Async port used for control port:

§ Vanguard 300: DECconnect connector

§ Vanguard 305: RJ45 connector

• Two MB FLASH, four MB DRAM

See Figure 1-4 for a view of the Vanguard 300/305 rear panel.

Motherboard

The motherboard supports up to three serial interfaces.

Serial Ports

The Vanguard 300/305 is available with one or two serial ports, plus an optional

third port for a daughtercard option (DSU, V.35 DIM site card, etc.). You can also

use the optional port for dial backup or as a second user port. See "Port

Characteristics" in this section for more details.

Vanguard 300 Ethernet Port

On the Vanguard 300, one port is a LAN port configured for Ethernet AUI and

10BaseT interfaces. Strapping is required during installation to configure the unit

for AUI or 10BaseT operation. The default configuration, shipped from the

factory, is 10BaseT.

Vanguard 305 Token Ring Port

On the Vanguard 305, one port is a LAN port configured for a Token Ring

connection. There are connectors for both shielded (STP) and unshielded (UTP)

cables, but only one cable can be connected at any time. No strapping is required

during installation to configure the unit as the port will automatically configure

for the connected interface.

The following table describes the port characteristics for the Vanguard 300/305.

Port

No.

Connector Interface Default Speed DTE/DCE

DB25

connector for

V.24, V.35,

V.36, V.11

DIM Site

Daughtercard

Frame

Relay

See Port 2

for DIM

speeds

• DIM Card

-Selectable

1

RJ48S

connector for

DSU

Daughtercard

DSU Sync

speed is 56

kbps

• DCE

• DSU -

NA

2 DB25

connector

Supported

DIMs include

V.11, V.35,

V.24, V.36,

Integral DSU

DIM Frame

Relay

• Maximum

async speed

is 115.2

kbps

• Maximum

sync speed

is 384 kbps

with INT

clocks or

1536 to

2048 kbps

with EXT

clocks

Selectable

3 DB25 V.24 Async

PAD

• Maximum

async speed

is DCE

115.2 kbps

• Maximum

synch speed

is 80 kbps

4 Async port Control

Terminal Port

(CTP) or serial

port (some

limitations).

CTP Maximum

async speed

is 19.2 kbps

DCE

LAN

Vanguard 300:

Ethernet

Support

includes:

• 10BaseT

• AUI

Either one of

the interfaces

can be

connected and

operated, but

not

simultaneously.

Ethernet 10 Mbps N/A

Vanguard 305:

Token Ring

Support

includes:

• STP

• UTP

Either one of

the interfaces

can be

connected and

operated, but

not

simultaneously.

Token

Ring

4 or 16

Mbps

(Default is 4

Mbps)

N/A

Memory

Two Mbytes of FLASH memory and four Mbytes of DRAM reside on the

motherboard. An optional SIMM can be used to expand DRAM to 8 Mbytes.

Example of the Vanguard 300/305 Front Panel

Figure 1-3 shows the front panel of the Vanguard 300/305.

Figure 1-3. Vanguard 300 /305 Front Panel

Front Panel DIP Switch Definitions

The six DIP switches on the front panel are defined as follows:

Switch

Position

Switch Name Down Up

1 Port 2 RI/TM Pin 22 is input on

Port 2.

Pin 22 is output on Port 2.

2 Port 2 MB Pin 25 is input on

Port 2.

Pin 25 is output on Port 2.

3 Port 3 RI/TM Pin 22 is input on

Port 3.

Pin 22 is output on Port 3.

4 Port 3 ->CTP Normal operation Configure Port 3 as PAD

port.

5 DIAGNOSTICS

Normal operation Reserved.

6 DEFAULT

NODE

Normal operation Resets all configurable

parameters to default values.

Example of the Vanguard 300 Back Panel

The Vanguard 300 back panel features the following connectors, as shown in

Figure 1-4.

Figure 1-4. Vanguard 300 Back Panel

Example of the Vanguard 305 Back Panel

The Vanguard 305 back panel features the following connectors, as shown in

Figure 1-5.

Figure 1-5. Vanguard 305 Back Panel

Cabling

All cables for the Vanguard 300/305 are the same cables used for the 6500 Series.

For example, DB25 cables, the 6509 EIM telco cable, and 6520 Ethernet cables

currently available for the 6500 Series can be used with the Vanguard 300/305.

The DSU telco cable is provided with the DSU daughtercard. Port 4 requires a

DECconnect interface cable on the Vanguard 300, and a straight through 8-

conductor RJ45 cable (e.g. Inmac P/N Q0462-1 or Black Box P/N RM-EL08MS-

07) for the Vanguard 305. See "Vanguard 300 Cabling Pinouts" and "Vanguard

300 Cabling Pinouts" in the "Connecting to the CTP" section in Chapter 2 for

information about the pinouts of the RJ45 to DB25 adapter.

Software

Introduction

This section describes the operating software for the Vanguard 300/305.

Operating Software

The operating software is compressed in FLASH and loaded into RAM for

operation. There are a variety of operating software bundles available for the

Vanguard family. See the Software Release Notice accompanying your Vanguard

product for feature information on the operating software for the Vanguard

300/305, and see the Vanguard 300/305 Software Download Guide (Part No.

09965-1, Rev B) for information on installing the operating software.

FCC Part 68 and Telephone Company Procedures and Requirements

for DSU

Introduction

Before the Motorola Vanguard 300/305 can be connected to the network, you

must:

• Provide the local telephone company with the equipment's registration

number

• Order the proper connections

This information is for North America only.

How to Order Connections

To order the proper connections, provide the telephone company with the

following information:

• Interface type

• Required USOC jack connector number

• Service code

• Facility interface codes

Interface Type USOC Jack

Connector

Service Code Facility Interface

Code

56-kbps digital interface RJ48S 6.0F 04DU5-56

Troubleshooting Your Connection

If any of your equipment is not operating correctly, immediately remove it from

the telephone line before it harms your network. If the telephone company notes

the problem, they may temporarily disconnect your service. They will notify you

in advance of the disconnection, when possible.

If advance notice is not feasible, you will be notified as soon as possible. When

you are notified, you will be given the chance to correct the problem and be

informed of your right to file a complaint with the FCC.

Customer-Provided Telephone Equipment

FCC regulations and telephone company procedures prohibit connection of

customer-provided equipment to telephone company-provided coin service

(central office-implemented systems). Connection to party lines is subject to state

tariffs.

Occasionally, the telephone company may make changes in their equipment,

operations, or procedures. If these changes affect your equipment or service, the

telephone company will provide written notice so you can make the necessary

changes to maintain uninterrupted service.

Contact your telephone company if you have any questions about your telephone

line.

In some circumstances, the telephone company may ask you for information

about your equipment that is connected to the telephone line. Within the United

States (at the request of the telephone company), you should provide your

equipment's FCC registration number. This number is located on the unit's label.

Setting Up the Vanguard 300/305

Overview

Introduction

This chapter describes site preparation, unpacking, and installation for the

Vanguard 300/305.

Preparing a Site

How to Choose a Site for the Vanguard 300/305

Choose a site that is within an appropriate distance of a power source. The

selected site should be free of accumulated dust and environmental extremes.

Depending on your application and the country in which the Vanguard 300/305

will operate, the power source must be a grounded 100 to 240 VAC outlet.

Warnings and Cautions

The following special notices apply to all equipment handling procedures in this

operator's guide.

Only trained, qualified technicians should perform procedures outlined in this

guide.

Motorola Vanguard 300/305 daughtercards and DIMs are sensitive to static

discharge, which can damage components. Trained, qualified technicians will

use proper handling and grounding precautions when handling a Motorola

Vanguard 300/305 daughtercard or DIM.

Ports capable of connecting to ports on other apparatus are defined as Safety

Extra Low Voltage (SELV). To conform with EN60950, ensure that these

ports are only connected to ports of the same type on other apparatus.

Avertissement

Les ports qui sont susceptibles d'etre connectes a des equipements sont

designes comme TBTS. Pour garantir la conformite a la norme EN 60950,

n'interconnecte ces ports qu'avec des ports du meme type sur des autres

materiels.

Warnung

Anschlusse, die mit anderen Geraten verbindet werden konnen, sind als SELV

beschrieben. Um Konformitat mit EN 60950 zu versichern, sichern Sie es, daß

diese Anschlusse nur mit den des selben Type auf anderen Geraten verbindet

werden.

Cable Clearance/Air Circulation

To avoid overheating the unit's circuitry, you should never place anything on top

of the unit, within 1 inch (2.5 cm) of the ventilation slots on the front panel, or

within 12 inches (30.5 cm) of the back of the unit. Allow at least 12 inches (30.5

cm) in back of the unit for interfacing cable clearance and air circulation, as

shown in Figure 2-1.

Figure 2-1. Proper cable and air clearance

Unpacking

What You Should Receive

The Vanguard 300/305 is packaged in shock-absorbent packing material. Inside

your shipping carton, you should find the following items:

• Vanguard 300/305 base unit

• Operator's Guide

• Telco cable for DSU (if ordered)

How to Unpack the Vanguard 300/305

Follow these steps to unpack the Vanguard 300/305.

Step Action

1

Check the shipping carton and its contents for damage.

2

Open the shipping carton from the top as shown in Figure 2-2.

3

Lift the Vanguard 300/305 from its shipping carton and remove the

packing material.

Vanguard 300/305 components are installed in the base unit before it is shipped

from the factory. In addition to the base unit and accompanying components, the

shipping carton may include a sleeve containing the power cord if you ordered

one.

Page is loading ...

Motorola 68230 - Vanguard 300 DSU/CSU User manual

This manual is also suitable for

Motorola 68230 - Vanguard 300 DSU/CSU User manual

Related papers

Other documents