2. Home
  3. Domestic appliances
  4. Large home appliances
  5. Cookers
  6. Fisher & Paykel
  7. CI604DTB3
CI604DTB3

Fisher & Paykel CI604DTB3 User guide

  • I have reviewed the datasheet for the Fisher & Paykel CI604DTB3 Induction Cooktop. This document provides detailed product dimensions, clearance requirements, and cutout dimensions for installation. I am ready to answer your questions about the specifications and installation of this induction cooktop.
  • What is the minimum clearance from the glass surface to a rangehood?
    What is the minimum clearance from the side edges of the cutout to the nearest combustible surface?
    What is the required minimum ventilation gap between the bottom of the bench and the top of cabinetry fronts?
0 100 200 400
millimetres
Model no:
CI604DTB3
Product Dimensions
mm
a Height of chassis (below top of bench including terminal block)
49
B Overall width of cooktop
600
c Overall depth of cooktop
530
D Height from benchtop datum to top of cooktop glass
5
e Width of chassis
549
f Depth of chassis
478
g Depth of front control panel
85
h Depth of cooktop cooking area
442
i Distance from side edges of cooktop to chassis
26
j Distance from front edge of cooktop to chassis
14
k Distance from back edge of cooktop to chassis
38
Minimum Clearances
mm
Minimum clearance from side edges of cutout to nearest
combustible surface
30
Minimum clearance from rear edge of cutout to nearest
combustible surface
30
Minimum clearance below top of benchtop to rear top of oven*
installed below cooktop or cabinetry
65
Minimum clearance from glass surface to rangehood
650
Minimum clearance from benchtop to overhead cabinet not
directly above the cooktop
450
Minimum ventilation gap between bottom of bench and top of
cabinetry fronts
4
*NOTE: The oven installed below the cooktop MUST have a cooling fan.
It is important that the induction cooktop receives adequate air supply.
For ventilation requirements please refer to the installation manual.
INDICATES CUTOUT -------------------------------------------------------
INDICATES CABINETRY / PRODUCT DATUM -------------------------
INDICATES CABINETRY CLEARANCES --------------------------------
DATE: 20.10.2016
IMPORTANT NOTE: Throughout this guide, dimensions may vary by ±2mm (1/16'').
Please read the installation manual for detailed information on installing the
product. For full installation instructions & specifications visit fisherpaykel.com
DATUM :
TOP OF BENCHTOP
600
B
e
530
C
h
g
DA
f
CLEARANCE : COMBUSTIBLE SURFACE
FRONT VIEW
PLAN VIEW
PROFILE VIEW
CLEARANCE : OVEN OR CABINETRY
CLEARANCE : RANGEHOOD
i i j k
CLEARANCE : OVERHEAD CABINET NOT DIRECTLY ABOVE COOKTOP
POWER CORD
LOCATION
POWER CORD
LOCATION
DATA SHEET
600mm Induction Cooktop
Model no:
CI604DTB3
Cutout Dimensions for CI604DTB3 only
mm
Overall width of cutout
560
Overall depth of cutout**
490
**Note cutout position is centred to the cooktop width but offset to the
cooktop depth. Cutout front depth is 10mm from the front edge of the
product.
Cutout Dimensions for CI604DTB3 with CG302DNGGB1
mm
a Overall width of cutout
865
b Overall depth of cutout
490
C Width of CI604DTB3 Induction Cooktop section of cutout
560
D Width of joining strip section of cutout
40
E Width of CG302DNGGB1 Gas Cooktop section of cutout
265
Electrical Specifications for CI604DTB3 only
7000W @ 220-240V/380V-415V 2N - 30A
IMPORTANT NOTE: For full installation and clearance details please refer to
our installation manual.
DATE: 20.10.2016
IMPORTANT NOTE: Throughout this guide, dimensions may vary by ±2mm (1/16'').
Please read the installation manual for detailed information on installing the
product. For full installation instructions & specifications visit fisherpaykel.com
CI604DTB3 INDUCTION COOKTOP
WITH JOINING STRIP AND
CG302DNGGB1 GAS ON GLASS COOKTOP
MULTIPLE ADJACENT COOKTOPS - EXAMPLE ONLY
B
A C
D
E
CG302DNGGB1
GAS ON GLASS COOKTOP
CI604DTB3
INDUCTION COOKTOP
COOKTOP JOINING STRIP
COUNTERTOP
DATA SHEET
600mm Induction Cooktop
/