Siemens BTC-1 Backup Tone Card User manual

Brand: Siemens

Model: BTC-1 Backup Tone Card

Type: User manual

INTRODUCTION

The Model BTC-1 Backup Tone Card from

Siemens Industry, Inc. provides two tones

for the MXLV System that can be selected

by dipswitches. This card can be installed on

top of the ACM-1 to provide backup of the

two primary tones should the tone generator

of the ACM-1 fail. The BTC-1 can also be

installed on the OCC-1 Output Control Card

module to provide a default tone when the

low power riser fails and when the OCC-1

loses contact with the MMB.

Select the two backup tones on switch S1 by

matching SW1-SW4 and SW5-SW8 to the

CSG-M (AccuLINK) configuration tone selec-

tions. Table 1 on the next page shows the

switch settings for each available tone.

For additional information on the Voice

System, refer to the MXLV Manual, P/N

315-092036.

INSTALLATION

Remove all system power before installa-

tion, first battery and then AC. (To power

up, first connect the AC and then the battery.)

1. Remove the card from its protective bag.

Installation Instructions

Model BTC-1

Backup Tone Card

2. Refer to the function section of the CSG-M

configuration printout for the tones to be

configured.

3. Set the desired tones on switch S1 using

dipswitches SW1-SW4 for the first tone

selection and dipswitches SW5-SW8 for

the second tone selection.

a. Refer to Figure 2 or 3 on page 3

for the location of S1.

b. Refer to Table 1 for the switch set-

tings and their associated tones.

c. Set the tones (See Note at the top

of the next page).

Do not install the BTC-1 on the ACM-1

or OCC-1 until the system is ready for

the installation of PC cards. Until then,

keep the BTC-1 in its protective bag.

Mounting

The BTC-1 mounts on either the ACM-1

(See Figure 2) or the OCC-1 (See Figure 3)

with two snap-in type standoffs and a comb-

like connector.

1. Install the standoffs and comb connector

in the component side of the ACM-1 or

the OCC-1, whichever is appropriate.

(See Note at top of the next page.)

P/N 315-090919-8

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

firealarmresources.com

GNITTES

ENOT

12345678

00000000 lagellI

X000X000 emihC

0X000X00zH0002

XX00XX00poohWwolS

00X000X0pleY

X0X0X0X0liaW

0XX00XX0edocainrofilaC

XXX0XXX0etunimrepseslup03tadeslupzH009

000X000Xlagelll

X00XX00XnroH

0X0X0X0X3edoclaropmeT

XX0XXX0Xetunimrepseslup03tadeslupzH009

00XX00XXwoeY

X0XXX0XXwoL/hgiH

0XXX0XXXlagellI

XXXXXXXXenotzH009

Note: To open a dipswitch, press down on the side of the dipswitch marked OPEN. To close a

dipswitch, press down on the side of the dipswitch opposite the side marked OPEN.

To open a slide switch, push the slide to the side opposite the side marked ON. To close a

slide switch, push the slide to the side marked ON.

X = Switch closed OR ON; 0 = Switch open OR OFF

Setting the Tones on Switch 1

TABLE 1

Figure 1

BTC-1 Backup Tone Card Module

Mount on an OCC-1 to provide

a default tone in degrade mode

when communication to the

MXL fails and there is a local

alarm detected. This is useful

only if the OCC-1 is providing

input to the amplifier.

Note: Mount on an ACM-1 to provide

a backup for the two primary

tones.

firealarmresources.com

2. Position the BTC-1 over the connector

and standoffs with the components of

the board facing out. Be certain that the

standoffs and the connector pins line

up with their respective holes in the

BTC-1 card and connector.

3. Place the BTC-1 on the standoffs and

connector by pressing them into place.

This takes some effort. Be careful be-

cause once the standoffs are installed,

they are difficult to remove. (If it is

Figure 3

Mounting the BTC-1 on the OCC-1

Figure 2

Mounting the BTC-1 on the ACM-1

necessary to remove the BTC-1 from

either the ACM-1 or the OCC-1, first

disconnect the system.)

ELECTRICAL RATINGS

tnerruCeludoMCDV5evitcAAm01

tnerruCeludoMCDV42evitcAAm04

tnerruCeludoMCDV42ybdnatSAm54

firealarmresources.com

P/N 315-090919-8

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

firealarmresources.com

Siemens BTC-1 Backup Tone Card User manual

Siemens BTC-1 Backup Tone Card User manual

Siemens BTC-1 Backup Tone Card User manual

Related papers

Other documents