2. MAHA
  3. AB 6-07 / AB 6-12 / AB 6-20

MAHA AB 6-07 / AB 6-12 / AB 6-20 Operating instructions

  • Hello! I have analyzed the operating instructions for the MAHA AB 6-07, AB 6-12, and AB 6-20 support stands. This document provides guidance on the safe usage, maintenance, and technical specifications of these support stands including important safety warnings. I'm ready to answer any questions you may have.
  • What is the intended use of these support stands?
    What type of ground should the support stands be used on?
    What is the the manufacturer's prescribed maintenance interval?
AB 6-07 | AB 6-12 | AB 6-20
Support Stands
Original Operating Instructions
BA492101-en
2 BA492101-en
BA492101-en
2022-10-04
© MAHA Maschinenbau Haldenwang GmbH & Co. KG
The reproduction, distribution and utilization of this document as well as the communication of its contents
to others without explicit authorization is prohibited. Offenders will be held liable for the payment of
damages. All rights reserved in the event of the grant of a patent, utility model or design.
The contents of this edition have been checked with great care. However, errors cannot be fully excluded.
Subject to technical change without notice.
Manufacturer
MAHA Maschinenbau Haldenwang GmbH & Co. KG
Hoyen 20
87490 Haldenwang
Germany
Phone: +49 8374 585-0
Fax: +49 8374 585-590
Mail: [email protected]
Web: www.maha.de
Service
MAHA SERVICE CENTER
Maybachstraße 8
87437 Kempten
Germany
Phone: +49 8374 585-100
Fax: +49 8374 585-491
Mail: service@maha.de
Web: www.mahaservicecenter.de
Contents
1 Safety ................................................................................................................................................................ 3
1.1 Introduction .................................................................................................................................................. 3
1.2 Symbols ........................................................................................................................................................ 3
1.3 Intended Use ................................................................................................................................................ 3
1.4 Safety Instructions ....................................................................................................................................... 3
1.5 What to Do in the Event of an Accident ...................................................................................................... 4
2 Description ....................................................................................................................................................... 5
2.1 Technical Data ............................................................................................................................................. 5
2.2 Accessories.................................................................................................................................................. 5
3 Operation .......................................................................................................................................................... 6
4 Maintenance ..................................................................................................................................................... 7
4.1 Annual Inspection ........................................................................................................................................ 7
4.2 Care Instructions ......................................................................................................................................... 7
4.3 Spare Parts ................................................................................................................................................... 7
5 Disposal ............................................................................................................................................................ 7
BA492101-en 3
1 Safety
1.1 Introduction
Thoroughly read this manual before operating the equipment and comply with
the instructions. Always display the manual in a conspicuous location.
Personal injury and property damage incurred due to non-compliance with these
safety instructions are not covered by the product liability regulations.
1.2 Symbols
CAUTION
indicates a potential hazard which, if not avoided, could result in moderate or
minor personal injury.
indicates important information notes.
1.3 Intended Use
These support stands are intended for the safe setting down of loads, e.g. mo-
tor vehicles, after they have been lifted with a wheel engaging lift.
Any use other than described is inappropriate.
1.4 Safety Instructions
• The detailed operating instructions must be referred to.
• The legal accident prevention regulations must be complied with.
• The device must only be operated by skilled persons, who are over 18 years
of age.
• Only use the support stands on solid, even ground, preferably concrete or as-
phalt.
• All load-bearing parts must be regularly subject to a visual inspection.
• Lighting of the workplace is the responsibility of the operator.
• The rated load capacity as specified on the name plate must not be exceed-
ed.
• The load must only be supported at the points intended for that purpose.
• For support stands without compensating spring:
Caution – downward movement of punch! When removing the securing pins,
do not place fingers between the punch and grommet.
• For support stands with compensating spring (note warning label):
Caution – upward movement of punch with sudden pressure release of
4 BA492101-en
spring! When removing the securing pins, do not bend over the punch and do
not place fingers between the punch and the load.
• After lowering, ensure the load is securely accommodated.
• Servicing work must only be carried out by authorized service technicians.
1.5 What to Do in the Event of an Accident
• The injured person is to be removed from the danger area. Find out where
dressing and bandages are kept. Seek first-aid.
• Provide first-aid (stop bleeding, immobilise injured limbs), report the accident
and seal off the accident site.
• Immediately report any accident to your supervisor. Make sure a record is
kept of every occasion first-aid is provided, e.g. in an accident book.
• Remain calm and answer any questions that may arise.
BA492101-en 5
2 Description
2.1 Technical Data
Model
AB 6-07
AB 6-12
AB 6-20
Load capacity [kg]
7500
7500
7500
Net weight [kg]
26
52
92
Adjustment range
[mm]
470…795
875…1395
1200…1965
Wheels
No
Yes
Yes
Compensating spring
No
No
Optional
2.2 Accessories
Item No.
Model
Designation
Suitable for
VZ 971287
APR II
Round base plate, pluggable
AB 6-07/12/20
VZ 971288
APRV II
Round base plate, adjustable
AB 6-07/12/20
VZ 971289
APV II
Square base plate, pluggable
AB 6-07/12/20
VZ 971290
APVV II
Square base plate, adjustable
AB 6-07/12/20
VZ 971167
AF 20
Compensating spring
AB 6-20
6 BA492101-en
3 Operation
1 Place support stands under the lifting points of the load. Only use the support
stands on solid, even ground, preferably concrete or asphalt.
2 Withdraw securing pins, bring punch to the desired height and secure using
pins. Always slide securing pins completely through the guide.
CAUTION
Risk of injury
For support stands without compensating spring:
Caution – downward movement of punch! When removing the securing pins, do
not place fingers between the punch and grommet.
For support stands with compensating spring (Note warning label, see figure):
Caution – upward movement of punch with sudden pressure release of spring!
When removing the securing pins, do not bend over the punch and do not place
fingers between the punch and the load.
3 Repeat procedure for all support stands. While doing so, ensure that all
punches are at the same height.
4 Slowly lower load and verify secure contact.
5 Remove lifting device.
6 Before commencing work on the load that has been set down, recheck to
ensure secure positioning.
7 Before removing the support stands, ensure load is securely accommodated
on the lifting device.
BA492101-en 7
4 Maintenance
4.1 Annual Inspection
• The maintenance interval prescribed by the manufacturer is 12 (twelve) mon-
ths. This maintenance interval refers to normal workshop usage. If the
equipment is used more frequently or under severe operating conditions (e.g.
outdoors), the interval must be reduced accordingly.
• Maintenance work shall be done only by authorised and trained service tech-
nicians provided by the manufacturer, licensed dealers or service partners.
• In case of non-compliance the manufacturer's warranty becomes void.
4.2 Care Instructions
• Periodically clean the equipment and treat it with a care product.
• Repair damage to the paintwork immediately to prevent corrosion.
• Do not use caustic cleaning agents or high pressure and steam jet cleaners
to avoid equipment damage.
4.3 Spare Parts
To ensure safe and reliable operation, only use original spare parts supplied by
the equipment manufacturer.
5 Disposal
If you want to dispose of the equipment, please contact your MAHA dealer or
the following address, indicating equipment type, date of purchase and serial
number:
MAHA Maschinenbau Haldenwang GmbH & Co. KG
Hoyen 20 | 87490 Haldenwang | Germany
Phone: +49 (0) 8374 585 0
Fax: +49 (0) 8374 585 500
Email: [email protected]
Alternatively, you may take the equipment to a specialised waste management
plant to ensure that all components and operating liquids are properly disposed
of.
8 BA492101-en
/