GE ZTD910SF4SS Installation guide

Brand: GE

Model: ZTD910SF4SS

Category: Warming drawers

Type: Installation guide

Installation

Instructions

If you have questions, ca!l 800,6E,CARESor visit ourwebsite at:w.monogram.com

27"and30"

Warming Drawers

Models:

ZKD910

ZTD910

Monogram:

Before you begin - Read these instructions coinpletely and careflllly:

IMPORTANT - Save these instIuctions for local inspector's use.

IMPORTANT - OBSERVE AI,I, GOVERNING CODES AND ORDINANCES.

Note to Installer - Be sure to leave these instiuctions with the Consunler.

Note to Consumer - Keep these instructions with vour Owner's Manual fi)i" fliture reference.

¥!,,,,r..l:_,_llL't_This appliance must be properly grounded. See "Electrical Supply", page 4. [

r!,w,._=l_,_llt.],_mCet appaxeil dolt 8tre correctement mis h la terre. Consulter page 4. [

If wm received a dainaged warining drawei;

w)u should inunediatelv contact w)ur dealer

or builder.

Proper installation is the responsibility of the

installer. Product taihu'e due to inlproper

installation is not covered under the GE

Appliance Warranty. See the Lrse 8.: Care

Guide fl)i" warranty inforination.

• Use this appliance only fi)r its intended

purpose.

Check with local utilities fi)i" electrical codes

that apply in your area. i,ocal codes vary.

Installation electrical connections and

grounding n/ust ctnnply with applical)le codes.

In the absence (if local codes, the drawer

should be installed in accordance with

National Electrical Code ANSI/NFPA 70-1990

or latest edition,

WARNING:

ANTI-TIP PRECAUTIONS

An anti-tip brace must be installed to

prevent the drawer from tipping forward

when opened and loaded. Failure to do so

could result in personal injury.

PRECAUTIONS :

CONTRE LE BASCULEMENT

Pour 6viter les blessures, il faut installer

mae patte de retenue pour empScher le

tiroir de basculer quand il est ouvert et

plein.

For Monogram local service in your area,

1.800.444.1845.

For Monogram service in Canada, call

1.888.880.3030.

For Monogram Parts mid Accessories, call

1.800.626.2002.

Con n

Design Information

Models Available .................................................................................................................................. 3

Product Diinensions ............................................................................................................................ 3

Accessories ........................................................................................................................................... 3

Tools and Materials Required ............................................................................................................ 3

Installation Preparation

Adwmce Planning ............................................................................................................................... 4

Grounding the Appliance ................................................................................................................... 4

ReInove the Packaging and Parts ....................................................................................................... 5

hlstallation Below a Countertop ........................................................................................................ 5

hlstallation Below Wall (-)veils ............................................................................................................ 6

Installation

Step 1: Provide Cabinet Support and Anti-Tip Bracket ................................................................... 7

Step 2: hlstall _4'arining Drawer ......................................................................................................... 7

Design Information

_.:D_rmir_g Drawer

ModeLs

Available.

ZTD910

30" Wide model

ZKD910

27" Wide model

The warming drawers may be installed

directl_ into a wall or wall oxen cabinetry

or beh)w a Cotlntertop,

P, oduct

Dimensions

_27'_ 23-1/4"_

',I Drawer 11 I ,

',I Open 9

" 26,,

E , t

10-1/2"

Dimension A

ZTD910 30"

ZKD910 26-3/4"

Accessories

ZXD27B, ZXD30B - This kit provides for the

) c _))

installation of a custom front panel ( n 2 t

and 30" black and white wide models,

NOTE: Theoriginal drawer front will beremovedand discarded

when this kit is used.Thetubular handlecan be reinstalled onto

the custom panelwith longerscrews (not provided).Or,the

original handle canbe replacedwith a custom handle of your

choice.(Handleis not supplied.) Choosea custom handleto match

or complement cabinetryhardware.

JXPN2 - Warming drawer pan kit. This kit

includes supports and one flfll size and one

half size pan with lids. The pans fit 27" and

30" wide models.

7boZs and

MateriaLs

Required

• Wood screws andadhesiveor other hardware for installing

runnersor shelf to support warmer drawer.

• 2x 4 or 2 x 2 lumber for runners

• 2x 4or 2 x 2 wood block for anti-tip security

• Saw

• Level

• Drill and1/16" bit

• Phillips screwdriver

Runnersmust be level, rigidly mounted andcapableof supporting

150pounds.

Design Information

Warmir_g Drawer

• The drawer may be installed below a

countertop, a cooktop, a single or double

oven and side by side using 2 drawers.

• The warming drawer can be installed below

approved cooktops. Allow 2" rain. clearance

fl'om bottom of cooktop burner box to top

of warming drawer cutout. See page 5.

• The warming drawer can be installed below

approved ovens. Allow a 2" rain. clearance

between Ctltotlts. Additional clearances may

be required. See page 6.

*Electrical power cord is located on the right

side of the warming oven. I,ocate the outlet

within reach of the 56" hmg power cord in

an a(!jacent cabinet, within 42" of the right

side or 16" fl'om the lett side of the cutout.

A recessed receptacle can be installed on the

right side of the cutout, 7" max. fl'om the

rear of cabinet.

Grounding

the Appliance

IMPORTANT - (Please read carefully)

FOR PERSONAL SAFETY, THIS APPLIANCE

MUST BE PROPERLY GROUNDED.

Do Ilot rise _111 exteIIsioIl cord or adapter

plug with this appliance. Follow National

electrical codes or prewfiling local codes

aIld oYdilla ilces.

This warming drawer must be supplied with

190V, 60Hz, and connected to an individual,

properly grounded branch circuit, and

protected bv a 15 or 20 amp circuit breaker

or time delay filse.

• A properly grounded 3-prong receptacle

should be located within reach of the

drawers' 56" long power cord.

• i,ocate the receptacle in an a(!jacent cabinet.

-within 42" of the right side or,

-within 16" of the lett side or,

-A recessed receptacle may be located on

the right side of the cutout, 7" froln the

back of the cabinet. In this location, the

excess power cord should be coiled and

taped to the right side of the unit.

• When two warming drawers are installed

side to side, they can operate from the same

receptacle.

Drill 1-1/2"Hole

ForPowerCordFor

Leftor RightSide

OutletLocation

IMPORTANT - (Please read carefully)

The power cord of this appliance is equipped

with a 3-prong (grounding) plug that mates

with a standard S-prong grounding wall

receptacle to minimize the possibility of

electric shock. The customer should have

the wall receptacle and circuit checked by

a qualified electrician to make sure the

receptacle is properly grounded and has the

correct polarity.

• Where a standard 2-prong wall receptacle is

encountered, it is the personal responsibility

and obligation of the customer to have it

replaced with a properly grounded 3-prong

wall receptacle.

Do IIOt, tlIlder _lily circtlillstaiices, CII[ 0I"

remove the third (ground) prong fl'om the

power cord.

DO NOT USE AN EXTENSION CORD,

Installation Preparation

Warming Drawer

Packaging

and Parts

Installation

Below a

Countertop

• Place carton on a fiat surfi_ce.

• Open one end of the carton and lift off

the top piece.

• I,ilt the Warlner up and out of the carton.

• Place the drawer on top of the shii)ping

carton to protect the drawer fl'ont and

the finished flooring.

• Remove all packing materials and tape.

• i,ocate package containing 4 wood screws

and set aside.

Parts provided:

• 4 _\'ood Screws

Electrical

Outlet16"Max.

FromLeft Side.

Install

2x4or 2x2

Anti-TipBlock ElectricalOutlet

AgainstRear FlushWith Side

CabinetWall ofCabinet7" Max.

9" FromFloor

to Bottom

of Block

ElectricalOutlet42"Max.

FromRightSide.

>/2 Install a Solid Barrier

-,z' Below a Cooktop

See Note

1-1/2" Cabinet Top

23-1/2"Min.

Solid Barrier

.Air Gap

Installa SolidBarrier

anda1/4" AirGap

AboveWarmingDrawer

• When installed, the fl'ont fi_ce of the drawer

will be nearly flush with a@_cent cabinetry

dooI'S.

• Drawer overlaps will conceal cut edges on

all sides of the opening,

The rough opening fin" the drawer must be:

- Depth: 23-1/2" rain. fl'om inside back to

front of cabinet fl'ame.

- Width: 25-1/2" fin" 27" wide models,

28-]/2" fin" 30" wide models.

- Height: 9-1/4".

• 5" rain. above floor or l" above toekick.

23-1/4" fi'om floor to bottom of cutout is

recollllllended t0i" tinder coHnterto l)

installation.

Installation below a cooktop:

Warming drawers are approved %r installa-

tion below only certain specified c{}{}kto I)

models, See the label attached to the top of

the warming drawer for api)roved models. A

solid barrier and air gap between cookto I) and

warming drawer is required, See Note above,

1"Min? 36"

Bountertop

9-1/4" ght

Dim. A

ZTDglO 28-1/2"

ZKDglO 25-1/2"

*NOTE: When installing thewarming drawer below a

cooktop,a solid barrier must beinstalled at least 1"from the

lowest point ofthe bottomof cooktop burner boxto the top of

cutout. Useany solid material suchas 1/4" thick plywood.

Allow at least 1/4" air gapbetween the barrier andthe top of

the warming drawer. See labelon top ofthe warming drawer

for approvedcooktopmodels.

Installation below a cabh_et drawer:

The warming drawer may be installed beneath

a cabinet drawer. In this installation, a solid

barrier should be installed above the warming

drawer to block access. Use any solid material

such as 1/4" thick i)lDvood. Allow at least 1/4"

air gap between the barrier and the top of the

warming drawer. Observe the 5" rain. above the

floor or ]" above the toekick minimum

installation height,

NOTE: If you are installing in fl'ameless cabinets,

it may be necessary to install 1/2" wide cleats to

accept drawer mounting scre_:s. See drawer to

find exact locations of mounting screws.

Side to Side Installation:

Install two warmii_g drawers in separate cutouts.

Allow 2" rain, between cutouts,

Side to Side Installation

Design Information

War mi*_g"l)rawer

Installation

Below

Wall Ovens

NOTE:Additional clearance between

cutoutsmay be required. Checkto be

surethat ovensupports abovethe

Warming Drawer location does not

obstructthe requiredinterior 23-1/2"

depth and9-1/4" height.

2x2or 2x4

Anti-]ip Block

AgainstRear

Wall, 9" From

Floorto

Bottomof

Block

2" Min.

Overlapon

All Sides

2x2or2x4

Anti-TipBlock

Against

Wall, 9" From

Floorto

Bottomof

Block

1" Min.AboveToekickorAdjust

to OvenInstallationHeight

_-1/2' Min.

Inside_-

Oven

Cutout

Allow 5/8"

Overlap on

All Sides

NOTE:Additional clearance between

cutouts mayberequired. Checkto be

surethat oven supportsabovethe

Warming Drawer locationdoes not

obstruct the requiredinterior 23-1/2"

depth and9-1/4" height.

10-1/2"

1" Min.AboveToekick

When installed under a wall oven:

X,_arming ch'awers are approvecl for installation

below only certain specifiecl wall oven models.

See the label attached to the top of the

warming ch'awer for apl)roved models.

• When installe(1, the front lace of the drawer

will be nearly flush with a(!iacent cabinetry

cloors.

• Drawer overlaps will conceal cut edges on

all sides of the opening,

The rough opening fin" the drawer must be:

- Depth: 23-1/2" rain. fl'om insicle back to

fl'ont of cabinet fl'ame.

- Width: 25-1/9" fin" 27" wide models,

28-]/2" for 30" wide m oclels.

- Height: 9-1/4".

- Allow 2" rain. between oven ant1 drawer

cutouts for clearance of overlal)s.

NOTE: If you are installing in frameless cabinets, it may

be necessary to install 1/2" wide cleats to accept

drawer mounting screws. See drawer for mounting

screw locations.

Installation

Warming" Drawer

P vide

Cabinet

Support

23-1/2"

2"x 4"or

EquivalentRunners

] / / _\

' J \=

= ,

27"

IMPORTANT: When installed below asingle or doubleoven,

checkto besure that any ovensupports abovethe cutout do not

obstruct the 23-1/2" required depth of the warming drawer cutout.

• A 2" rain. clearance between ()veil and

wanning drawer cutouts are required.

Additional clearance may be required if

2 x 4 blocks are used to sui)port runners or

solid floor of the ()veil above.

• The warmer drawer may be supl)orted by

either a solid bottom, 2 x 4 or 2 x 2 runners.

23-1/F

/.(j_ 2"x 4" or

Equivalent Runners

// _\ ,

/ \ :i

_2F_

30"

• The suI)I)ort must be level and rigidly

mounted, flush with the bottom edge of

the cutout.

- There is no way to level the drawer once

it has been installed. Be sure sui)ports are

level.

• The entire weight of the drawer is SUl)l)orted

by the itlnners or solid floor and mtlSt be

capable of supi)orting 150 lbs.

stq) z

Install

Anti-Tip

Brachets

WARNING:

ANTI-TIP PRECAUTIONS

An anti-tip brace must be installed to prevent

the drawer from tipping forward when

opened and loaded. Failure to do so could

result in personal injury.

PRI CAUTIONS :

CONTRE LE BASCULEMENT

Pour 6viter les blessures, il faut installer role

patte de retenue pour emp6cher le tiroir de

basculer quand il est ouvert et plein.

., 2x4 or 2x2 ...

/" Runners or Solid ".-

Bottom

Install

2x4or2x2

Anti-TipBlock

AgainstRear

CabinetWail

9" FrornFloor

to Bottorn

of Block

St@ 2

Install

Warming

Drawer

• Slide left corner of tile drawer into tile

opening.

• Push power cord into the hole leading to

the outlet location. Thread the cord through

as drawer is being i)ushed back into the

opening. Check to be sure power cord does

not get trapped tulcler tile drawer.

- If the outlet is installed inside the

opening, i)lug tile cord into tile outlet.

In this location, the excess power cord

length should be coiled and taped to

the right side of the unit.

• Push the drawer back tmtil the fl'ont flange

is flush to tile cabinet fl'ont.

• Open tile drawer flfllv.

• Drill pilot holes through tile holes in tile

overlaping fl'allle_ one on each Coi'nei',

• Drive wood screws provided into each coi'nei',

NOTE:While performing installations described in this book,

safety glasses or goggles should be worn.

Mon(g_a_ I( al_-_z e._)o a a, call

1.600.444. l,_4 5.

)

NOTE: 1 roduct improv( mere is a contim/ing (md(avor

at G(_n(_ral El(ctric. Tht r(for(_, materials, apF,(m_mlc(

and sl)ecificalions are sul_iect to change wilholll notic(.

Pub.No.49-8937-2

Dwg. No. 164D3333P167

09-04JR

PrintedintheUnitedStates

Monogram:

GEConsumer & Industrial

Louisvifle, KY40225

_2004 GE Company

GE ZTD910SF4SS Installation guide

Brand: GE

Model: ZTD910SF4SS

Category: Warming drawers

Type: Installation guide

Download PDF

report

GE ZTD910SF4SS Installation guide

GE ZTD910SF4SS Installation guide

Related papers

Other documents