Paradyne 6381-A3 User manual

6381-A3 Router

User’s Guide

Document No. 6381-A2-GB23-10

January 2005

A January 2005 6381-A2-GB23-10

Printed in U.S.A.

Notice

This publication is protected by federal copyright law. No part of this publication may be copied or distributed,

transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form or

by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the express

written permission of Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773.

Paradyne Corporation makes no representation or warranties with respect to the contents hereof and specifically

disclaims any implied warranties of merchantability or fitness for a particular purpose. Further, Paradyne Corporation

reserves the right to revise this publication and to make changes from time to time in the contents hereof without

obligation of Paradyne Corporation to notify any person of such revision or changes.

Changes and enhancements to the product and to the information herein will be documented and issued as a new

release to this manual.

Warranty, Sales, Service, and Training Information

Contact your local sales representative, service representative, or distributor directly for any help needed. For additional

information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or

Paradyne worldwide office locations, use one of the following methods:

 Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty at

www.paradyne.com/warranty.)

 Telephone: Call our automated system to receive current information by fax or to speak with a company

representative.

— Within the U.S.A., call 1-800-870-2221

— Outside the U.S.A., call 1-727-530-2340

Document Feedback

We welcome your comments and suggestions about this document. Please mail them to Technical Publications,

Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or send e-mail to user[email protected]. Include the

number and title of this document in your correspondence. Please include your name and phone number if you are

willing to provide additional clarification.

Trademarks

Acculink, Bitstorm, Comsphere, DSL the Easy Way, ETC, Etherloop, FrameSaver, GranDSLAM, GrandVIEW, Hotwire,

the Hotwire logo, iMarc, Jetstream, MVL, NextEDGE, Net to Net Technologies, OpenLane, Paradyne, the Paradyne

logo, Paradyne Credit Corp., the Paradyne Credit Corp. logo, Performance Wizard, ReachDSL, StormPort, TruePut are

registered trademarks of Paradyne Corporation.

ADSL/R, Connect to Success, Hotwire Connected, JetFusion, JetVision, MicroBurst, PacketSurfer, Quick Channel,

Reverse Gateway, Spectrum Manager, and StormTracker are trademarks of Paradyne Corporation.

All other products or services mentioned herein are the trademarks, service marks, registered trademarks, or

registered service marks of their respective owners.

6381-A2-GB23-10 January 2005 B

Important Safety Instructions

1. Read and follow all warning notices and instructions marked on the product or included in the manual.

2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to

protect it from overheating, these slots and openings must not be blocked or covered.

3. Do not allow anything to rest on the power cord and do not locate the product where persons will walk on the power

cord.

4. Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous high

voltage points or other risks. Refer all servicing to qualified service personnel.

5. General purpose cables are used with this product for connection to the network. Special cables, which may be

required by the regulatory inspection authority for the installation site, are the responsibility of the customer. Use a

UL Listed, CSA certified, minimum No. 24 AWG line cord for connection to the Digital Subscriber Line (DSL)

network.

6. When installed in the final configuration, the product must comply with the applicable Safety Standards and

regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate regulatory

agencies and inspection authorities to ensure compliance.

7. A rare phenomenon can create a voltage potential between the earth grounds of two or more buildings. If products

installed in separate buildings are interconnected, the voltage potential may cause a hazardous condition. Consult

a qualified electrical consultant to determine whether or not this phenomenon exists and, if necessary, implement

corrective action prior to interconnecting the products.

8. Input power to this product must be provided by one of the following: (1) a UL Listed/CSA certified power source

with a Class 2 or Limited Power Source (LPS) output for use in North America, or (2) a certified transformer, with a

Safety Extra Low Voltage (SELV) output having a maximum of 240 VA available, for use in the country of

installation.

9. In addition, since the equipment is to be used with telecommunications circuits, take the following precautions:

— Never install telephone wiring during a lightning storm.

— Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

— Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the

network interface.

— Use caution when installing or modifying telephone lines.

— Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of

electric shock from lightning.

— Do not use the telephone to report a gas leak in the vicinity of the leak.

CE Marking

When the product is marked with the CE mark on the equipment label, a supporting Declaration of Conformity may be

downloaded from the Paradyne World Wide Web site at www.paradyne.com. Select Library → Technical Manuals →

CE Declarations of Conformity.

FCC Part 15 Declaration

An FCC Declaration of Conformity may be downloaded from the Paradyne World Wide Web site at www.paradyne.com.

Select Support -> Technical Manuals -> Declarations of Conformity.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device

may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

The authority to operate this equipment is conditioned by the requirement that no modifications will be made to the

equipment unless the changes or modifications are expressly approved by the responsible party.

!

C January 2005 6381-A2-GB23-10

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

Notice to Users of the United States Telephone Network

The following notice applies to versions of the modem that have been FCC Part 68 approved.

This equipment complies with Part 68 of the FCC rules and the requirements adopted by the Administrative Council for

Terminal Attachment (ACTA). On the bottom side of this equipment is a label that contains, among other information, a

product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the Telephone

Company.

This equipment is intended to connect to the Public Switched Telephone Network through a Universal Service Order

Code (USOC) type RJ11C jack. A plug and jack used to connect this equipment to the premises wiring and telephone

network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant

telephone cord and modular plug is provided with this product. It has been designed to be connected to a compatible

modular jack that is also compliant.

The Ringer Equivalence Number (or REN) is used to determine the number of devices that may be connected to a

telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming

call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that

may be connected to a line, as determined by the total RENs, contact the local Telephone Company. The REN for this

product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the

REN without a decimal point. For example, 03 represents a REN of 0.3.

If the modem causes harm to the telephone network, the Telephone Company will notify you in advance that temporary

discontinuance of service may be required. But if advance notice is not practical, the Telephone Company will notify the

customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is

necessary.

The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the

operation of the equipment. If this happens, the Telephone Company will provide advance notice in order for you to

make necessary modifications to maintain uninterrupted service. If trouble is experienced with the modem, refer to the

repair and warranty information in this document.

If the equipment is causing harm to the telephone network, the Telephone Company may request that you disconnect

the equipment until the problem is resolved.

The user may make no repairs to the equipment.

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service

commission or corporation commission for information.

If the site has specially wired alarm equipment connected to the telephone line, ensure the installation of the modem

does not disable the alarm equipment. If you have questions about what will disable alarm equipment, consult your

Telephone Company or a qualified installer.

6381-A2-GB23-10 January 2005 D

Supplier's Declaration of Conformity

Place of Issue:

Paradyne Corporation

8545 126th Avenue North

Largo, FL 33773-1502

USA

Date of Issue: 4/2/2004

Paradyne Corporation, located at the above address, hereby certifies that Model Number 6381-A2-210, bearing

labeling identification number US:AW2DL03B6381-AX, complies with: the Federal Communications Commission's

("FCC") Rules and Regulations 47 CFR Part 68, the Administrative Council on Terminal Attachments ("ACTA")-adopted

technical criteria TIA-968-A, "Telecommunications - Telephone Terminal Equipment -Technical Requirements for

Connection of Terminal Equipment To the Telephone Network, October 2002."

Patrick Murphy

Senior Vice President, Chief Financial Officer

Notice to Users of the Canadian Telephone Network

NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is

confirmed by the registration number. The abbreviation IC before the registration number signifies that registration was

performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It

does not imply that Industry Canada approved the equipment.

NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is labeled on the equipment. The REN

assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be

connected to a telephone interface. The termination on an interface may consist of any combination of devices subject

only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.

If your equipment is in need of repair, contact your local sales representative, service representative, or distributor

directly.

CANADA - EMI NOTICE:

This Class B digital apparatus meets all requirements of the Canadian interference-causing equipment regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du règlement sur le matérial brouilleur du

Canada.

!

E January 2005 6381-A2-GB23-10

Japan Notices

This is a Class B product based on the standard of the Voluntary Control Council for

Interference from Information Technology Equipment (VCCI). If this is used near a radio or

television receiver in a domestic environment, it may cause radio interference. Install and use

the equipment according to the instruction manual.

6381-A2-GB23-10 January 2005 i

Contents

About This Guide

 Document Purpose and Intended Audience . . . . . . . . . . . . . . . . . . . . v

 Document Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

 Product-Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

1 Introduction

 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

 Features of the 6381 Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

 Ports and Buttons (Back Panel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

 LED Description (Front Panel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

 Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

2 Hardware Installation and PC Setup

 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

 Connecting the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

 Configuring Your PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

 Windows USB Driver Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

 Configuring Your PC’s IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Assigning an IP Address to your PC Automatically by DHCP . . . . 2-6

Windows XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Windows 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Windows ME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Windows 95, 98 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

Windows NT 4.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

3 Using the Web Interface

 Logging Into Your Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

 Home Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

 Quick Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Contents

ii January 2005 6381-A2-GB23-10

 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Wide Area Network Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Local Area Network Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Saving Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

 Configuring the WAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

 New Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

PPPoE Connection Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

PPPoA Connection Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Static Connection Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

DHCP Connection Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

Bridged Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13

CLIP Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

 Modify an Existing Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16

 Modem Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17

 TSML . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17

 Configuring the LAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18

Enable/Disable DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19

 Changing the Router's IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20

 Firewall/NAT Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21

 Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22

UPnP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22

SNTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23

SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24

IP QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25

Port Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25

IP Filters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27

LAN Clients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28

LAN Isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28

Bridge Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-29

Multicast. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-31

IGMP Snooping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32

Static Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32

Dynamic Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33

Access Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-35

 Log Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-35

Contents

6381-A2-GB23-10 January 2005

iii

 Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-36

System Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-36

Remote Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-36

User Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-37

Update Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-38

Analyzer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-39

Ping Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-39

Modem Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-40

 Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-41

4 Troubleshooting

 The Router Is Not Functional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

 You Cannot Connect to the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

 LEDs Blink in a Sequential Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

 The Status LED Continues to Blink . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

 The Status LED is Always Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

A Terminology

 What is a Firewall?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

 What is NAT? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

 What is a DMZ? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

 What is a Router? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Index

Contents

iv January 2005 6381-A2-GB23-10

6381-A2-GB23-10 January 2005 v

About This Guide

Document Purpose and Intended Audience

This guide contains detailed information about the 6381-A3 router. It is intended

for all users of the router.

Document Summary

A master glossary of terms and acronyms used in Paradyne documents is

available online at www.paradyne.com. Select Support → Technical Manuals →

Technical Glossary.

Section Description

Chapter 1, Introduction Describes the features of the router.

Chapter 2, Hardware

Installation and PC Setup

Shows how to connect the router and set up your PC to

manage the router.

Chapter 3, Using the Web

Interface

Explains how to use the web interface to configure and

monitor the router.

Chapter 4, Troubleshooting Contains tips on troubleshooting common problems.

Appendix A, Terminology Explains some major internetworking concepts.

Index Lists key terms, concepts, and sections in alphabetical

order.

About This Guide

vi January 2005 6381-A2-GB23-10

Product-Related Documents

Complete documentation for Paradyne products is available online at

www.paradyne.com. Select Support → Technical Manuals.

To order a paper copy of a Paradyne document, or to speak with a sales

representative, please call 1-727-530-2000.

6381-A2-GB23-10 January 2005 1-1

1

Introduction

Definitions

Before you install or use your new router, you may find it helpful to understand the

following terms:

 A bridge is a device that forwards any message from one part of a network to

another.

 A router is a device that forwards messages according to their network

addresses.

 ADSL is Asymmetric Digital Subscriber Line, a version of DSL that allows a

higher speed for information coming from the Internet to your PC

(“downstream”) than it does for information going to the Internet from your PC

(“upstream”).

 ReachDSL is a version of DSL that works on lines too long or too noisy for

ADSL.

 ADSL/R is technology that combines ADSL and ReachDSL in one device.

The Model 6381 is a Digital Subscriber Line (DSL) modem that may be set by you

to run in bridge or router mode. Because it is most frequently used as a router, that

is how it is referred to in this manual. It supports ADSL/R.

Features of the 6381 Router

Your router has the following features:

 Support for ADSL2+ and ReachDSL (ADSL/R)

 10/100BaseT Ethernet port

 USB port

 The ability to connect multiple PCs to the Internet with just one WAN IP

Address (when configured in router mode with NAT enabled)

 A user-friendly web interface for configuration and monitoring

 Single-session IPSec and PPTP passthrough for Virtual Private Network

(VPN)

1. Introduction

1-2 January 2005 6381-A2-GB23-10

 Preconfigured port settings for many popular games

 Ability to act as a DHCP Server on your network

 Compatibility with virtually all standard Internet applications

 Address filtering and DMZ hosting

 Downloadable flash software upgrades

 Support for up to eight Permanent Virtual Circuits (PVCs)

 Support for up to two PPPoE sessions

System Requirements

In order to use your modem for Internet access, you must have the following:

 ADSL service subscription from your ISP.

 One computer with an Ethernet 10/100BaseT network interface card (NIC) or

a free USB port.

 (Optional) An Ethernet hub or switch, if you are connecting the device to

several computers on an Ethernet network.

 For system monitoring or configuration using the supplied web interface, a

web browser such as Internet Explorer Version 5.5 or later.

Ports and Buttons (Back Panel)

 POWER is where you connect the power supply.

 RESET Button: The RESET button is used to reset the router to the factory

default settings selected by your service provider. Do not use the RESET

button unless advised to by your service representative.

 LAN (Local Area Network) port: This is used to connect to Ethernet network

devices, such as a PC, hub, switch, or router.

 USB (Universal Serial Bus port): Connects to a PC's serial port. The router

supports Windows-based PCs using an RNDIS driver (included on the CD).

 PHONE port: This allows a phone to directly connect to the router. You do not

need to add splitter to the phone you connect here, since the router has an

internal splitter.

 LINE port: This is the DSL interface which connects directly to your phone line.

1. Introduction

6381-A2-GB23-10 January 2005

1-3

LED Description (Front Panel)

 Power LED: On indicates that the power is supplied to the router.

 Status LED: The Status LED serves two purposes. If the LED is continuously

lit, the DSL interface is successfully connected to a device through the LINE

port. If the LED is flickering, it is an indication that the router is training

(negotiating the connection to its partner modem).

 Activity LED: The Activity LED shows the state of the PPPoA or PPPoE

connection. Off: no PPP connection is established or the connection is not

used. Blinking: a PPP connection is being attempted. Solid green: a PPP

connection is established.

 LAN LED: The LAN LED serves two purposes. If the LED is continuously lit,

the Ethernet interface is successfully connected to a device through the LAN

port. If the LED is flickering, it is an indication of network activity.

 USB LED: The USB LED serves two purposes. If the LED is continuously lit,

the USB interface is successfully connected to a device through the LAN port.

If the LED is flickering, it is an indication of network activity.

05-17610

USB

LAN

ACTIVITY

STATUS

POWER

1. Introduction

1-4 January 2005 6381-A2-GB23-10

Packing List

 Your router is shipped with the following:

 Power adapter

 Ethernet cable (RJ45, straight-through wiring)

 Phone cable (RJ11)

 USB cable

 CD-ROM containing this manual and USB drivers

04-17511

USB

LAN

ACTIVITY

STA TUS

POW

ER

6381-A2-GB23-10 January 2005 2-1

2

Hardware Installation and

PC Setup

Overview

This chapter provides basic instructions for connecting the router to a computer or

a LAN and to the Internet using DSL. The first part provides instructions to set up

the hardware, and the second part describes how to prepare your PC for use with

the router. Refer to Chapter 3, Using the Web Interface for router configuration

instructions.

It is assumed that you have already subscribed to DSL service with your telephone

company or other Internet service provider (ISP).

Connecting the Hardware

Shut down your PC before connecting the router. To connect your router:

Procedure

1. Connect the supplied modular phone cable to the LINE port, and connect the

other end of the cable to your phone jack.

2. If you would like to use a phone in the vicinity of the router, connect it to the

PHONE jack of the router using the cord that came with your telephone. The

router has an internal POTS filter, so you do not need to install one here.

3. Connect the USB port, the LAN port, or both.

— If you are connecting the router directly to a PC (rather than to a LAN), you

can use either the USB port or the LAN port. (Do not connect both the

USB port and the LAN port to the same PC.)

To use the USB port, connect the supplied USB cable to the USB port of

the router, then connect the other end of the cable to a free USB port on

your PC.

When you start your PC (in a later step), Windows will detect the new

hardware and initiate the Found New Hardware Wizard. Follow the

instructions under Windows USB Driver Installation on page 2-3.

— Alternatively, you can use the included Ethernet cable to connect your

computer directly to the router. Attach one end of the supplied Ethernet

2. Hardware Installation and PC Setup

2-2 January 2005 6381-A2-GB23-10

cable to the LAN port and connect the other end to the 10/100BaseT port

on the network interface card in your PC.

— If your LAN has more than one computer, you can attach one end of an

Ethernet cable to a hub or a switch and the other to the port labeled LAN

on the router. This probably will require an Ethernet crossover cable. See

the documentation for your hub or switch to be sure.

4. Connect the cylindrical power plug into the POWER connector on the back of

the device. Next:

— If you have a wall-mount adapter, plug the AC adapter into a wall outlet or

a power strip.

— If you have a table-top adapter, use the AC power cord to connect the

adapter to a wall outlet or power strip.

The supplied power adapter may look different than the one illustrated here.

5. Turn on your PC any other LAN devices, such as hubs or switches.

Figure 2-1. Hardware Installation

04-17510

LINE LAN POWERPHONE USB

OR

1

2

3

4

DEFAULT

RESET

2. Hardware Installation and PC Setup

6381-A2-GB23-10 January 2005

2-3

Configuring Your PC

Before you start to access the router via Ethernet, you must configure your PC's

TCP/IP address to be 192.168.1.x, where x is any number between 2 and 254.

The subnet mask must be 255.255.255.0. Your router's default IP address is

192.168.1.1.

If you used the Ethernet cable to connect your router and PC, you do not need any

specific driver installation and you can skip Windows USB Driver Installation,

below. If you used the USB cable on a PC running a Windows operation system,

install the provided USB driver.

Windows 95 and Windows NT 4.0 do not support USB without additional software

(not included with your router). If USB driver installation fails under those operating

systems, contact your service provider.

Windows USB Driver Installation

As soon as you connect the USB cable between your PC and the router, Windows

will detect new hardware and the Found New Hardware Wizard will pop up. To

install the USB driver:

Procedure

1. Choose "Install from a list or specific location" and click on Next (Figure 2-2).

Figure 2-2. Found New Hardware Wizard

2. Hardware Installation and PC Setup

2-4 January 2005 6381-A2-GB23-10

2. Insert the supplied CD and use Browse to include the location D:\drivers in the

search, where D: is the letter you use for your CD drive (Figure 2-3).

Figure 2-3. New Hardware Installation Options

3. The Wizard will ask you to confirm the hardware installation. Choose Continue

Anyway. Windows will then install the supplied USB driver on your PC

(Figure 2-4 and Figure 2-5).

Figure 2-4. Hardware Installation Confirmation

Page is loading ...

Paradyne 6381-A3 User manual

This manual is also suitable for

Paradyne 6381-A3 User manual

Related papers

Other documents