Victaulic L080489XT0 Installation guide

Type
Installation guide

This manual is also suitable for

The Victaulic L080489XT0 is a 4" Style 489XT rigid coupling designed for use with Schedule 10 and 40 steel pipe. It features a one-piece EPDM gasket that provides a positive seal and eliminates the need for separate gaskets and sealants. The coupling is easy to install, requiring only a single wrench to tighten the nuts. It is also reusable, making it a cost-effective option for temporary or permanent installations. The L080489XT0 is ideal for use in a variety of applications, including water, wastewater, chemical, and mining.

The Victaulic L080489XT0 is a 4" Style 489XT rigid coupling designed for use with Schedule 10 and 40 steel pipe. It features a one-piece EPDM gasket that provides a positive seal and eliminates the need for separate gaskets and sealants. The coupling is easy to install, requiring only a single wrench to tighten the nuts. It is also reusable, making it a cost-effective option for temporary or permanent installations. The L080489XT0 is ideal for use in a variety of applications, including water, wastewater, chemical, and mining.

I-100_88
45"/%"3%$061-*/(4'03(3007&%&/%
1*1&*/45"--"5*0/*/4536$5*0/43&7@&
Style 005 - FireLock
®
Rigid Coupling
4UZMFZero-Flex
®
Rigid Coupling (12-inch/323.9-mm and Smaller Sizes)
4UZMFRigid Stainless Steel Coupling for Stainless Steel Pipe (4-inch/114.3-mm
and Smaller Sizes)
8"3/*/(
t 3FBEBOEVOEFSTUBOEBMMJOTUSVDUJPOTCFGPSFBUUFNQUJOHUPJOTUBMMBOZ7JDUBVMJD
piping products.
t %FQSFTTVSJ[FBOEESBJOUIFQJQJOHTZTUFNCFGPSFBUUFNQUJOHUPJOTUBMMSFNPWF
or adjust any Victaulic piping products.
t 8FBSTBGFUZHMBTTFTIBSEIBUBOEGPPUQSPUFDUJPO
'BJMVSFUPGPMMPXUIFTFJOTUSVDUJPOTDPVMESFTVMUJOTFSJPVTQFSTPOBMJOKVSZJNQSPQFS
product installation, and/or property damage.
NOTICE
t 5IFGPMMPXJOHJOTUBMMBUJPOTUFQTGFBUVSFQIPUPTPGB4UZMF$PVQMJOH)PXFWFS
UIFTBNFJOTUBMMBUJPOTUFQTBQQMZUP4UZMF3JHJE4UBJOMFTT4UFFM$PVQMJOHT
BOE4UZMF;FSP'MFY3JHJE$PVQMJOHTJOUIFTJ[FSBOHFTMJTUFEBCPWF
 'PMMPXTUFQToPGUIF
i1SFQBSBUPSZ4UFQTGPS$PVQMJOH
*OTUBMMBUJPOwTFDUJPO
 "44&.#-&)064*/(4 Insert
one bolt into the housings, and thread the
nut loosely onto the bolt to allow for the
“swing-over” feature, as shown above.
/05& The nut should be backed off no
further than flush with the end of the bolt.
$"65*0/
t .BLFTVSFUIFHBTLFUEPFTOPU
CFDPNFSPMMFEPSQJODIFEXIJMF
installing the housings.
'BJMVSFUPGPMMPXUIJTJOTUSVDUJPODPVME
DBVTFEBNBHFUPUIFHBTLFUSFTVMUJOH
JOKPJOUMFBLBHF
 */45"--)064*/(4 Using the
“swing-over” feature, install the housings
over the gasket. Make sure the housings’
keys engage the grooves completely on
both pipe ends.
NOTICE
'PS4UZMF$PVQMJOHT4VQQMJFEXJUI
4UBJOMFTT4UFFM#PMUTBOE/VUT
t Apply an anti-seize compound to
UIFCPMUUISFBETCFGPSFUJHIUFOJOH
the nuts.
I-100_89
45"/%"3%$061-*/(4'03(3007&%&/%
1*1&*/45"--"5*0/*/4536$5*0/43&7@&
 */45"--3&."*/*/(#0-5
/65Install the remaining bolt, and
thread the nut finger-tight onto the bolt.
/05& Make sure the oval neck of each
bolt seats properly in the bolt hole.
Angle Pad
Contact
Osets
Osets
Equal osets
at both pairs
of bolt pads
Exaggerated for clarity
 5*()5&//654Tighten all nuts
evenly by alternating sides until metal-
to-metal contact occurs at the angle
bolt pads. Make sure the housings’ keys
engage the grooves completely on both
pipe ends and that the offsets are equal at
the bolt pads. Equal, positive offsets are
necessary to ensure a rigid joint (refer to
the example above). /05& It is important
to tighten all nuts evenly to prevent gasket
pinching.
8"3/*/(
t For Victaulic rigid, angle-bolt-
pad couplings, the nuts must be
tightened evenly by alternating
sides until metal-to-metal c ontact
occurs at the bolt pads.
t For Victaulic rigid, angle-bolt-pad
DPVQMJOHTFRVBMPGGTFUTNVTUCF
present at the bolt pads.
t ,FFQIBOETBXBZGSPNDPVQMJOH
openings during tightening.
'BJMVSFUPGPMMPXUIFTFJOTUSVDUJPOT
DPVMEDBVTFKPJOUGBJMVSFTFSJPVT
personal injury, and property damage.
GOOD
BAD
6. Visually inspect the bolt pads at each
joint to ensure metal-to-metal contact is
achieved.
B'0345:-&$061-*/(4
0/-:The Style 489 coupling assembly
has a torque requirement (refer to the table
below).
4UZMF5PSRVF3FRVJSFNFOUT
Size
Torque
3FRVJSFNFOUT
Nominal Size
inches or mm
Actual Pipe
Outside
Diameter
inches/mm
GUMCT
/tN
1 ½ – 2 ½
1.900 – 2.875 18
48.3 – 73.0 25
76.1 mm
3.000 18
76.1 25
3 – 4
3.500 – 4.500 45
88.9 – 114.3 61
I-100_90
45"/%"3%$061-*/(4'03(3007&%&/%
1*1&*/45"--"5*0/*/4536$5*0/43&7@&
4UZMFBOE)FMQGVM*OGPSNBUJPO
Size Style 005 4UZMF 4UZMF
Nominal
Size
inches or
mm
Actual Pipe
Outside
Diameter
inches/
mm
Nut Size
inches/
Metric
4PDLFU
Size
inches/
mm
Nut Size
inches/
Metric
4PDLFU
Size
inches/
mm
Nut Size
inches/
Metric
4PDLFU
Size
inches/
mm
1
1.315
——
⁄ ⁄
——
33.7 M10 17
1 ¼
1.660 ⁄ ⁄ ⁄ ⁄
——
42.4M1015M1017
1 ½
1.900 ⁄ ⁄ ⁄ ⁄ ⁄ ⁄
48.3 M10 15 M10 17 M10 17
2
2.375 ⁄ ⁄ ½ ⁄ ⁄ ⁄
60.3 M10 15 M12 22 M10 17
2 ½
2.875 ⁄ ⁄ ½ ⁄ ⁄ ⁄
73.0 M10 15 M12 22 M10 17
76.1 mm
3.000 ⁄ ⁄ ½ ⁄ ⁄ ⁄
76.1 M10 15 M12 22 M10 17
3
3.500 ⁄ ⁄ ½ ⁄ ½ ⁄
88.9 M10 15 M12 22 M12 22
3 ½
4.000
——
½
——
101.6 M12 22
4
4.500 ⁄ ⁄ ½ ⁄ ½ ⁄
114 .3 M10 15 M12 2 2 M12 2 2
108.0 mm
4.250 ⁄ ⁄ ½ ⁄
——
108.0 M10 15 M12 22
5
5.563 ½ ¾ ⁄ 1 ⁄
——
141.3 M12 18 M16 27
133.0 mm
5.250 ½ ¾ ⁄ 1 ⁄
——
133.0 M12 18 M16 27
139.7 mm
5.500 ½ ¾ ⁄ 1 ⁄
——
139.7 M12 18 M16 27
6
6.625 ½ ¾ ⁄ 1 ⁄
——
168.3 M12 18 M16 27
159. 0 m m
6.250 ½ ¾ ⁄ 1 ⁄
——
159.0 M12 18 M16 27
165.1 mm
6.500 ½ ¾ ⁄ 1 ⁄
——
165.1 M12 18 M16 27
8
8.625 ¾ 1 ¼ ¾ 1 ¼
——
219.1 M20 32 M20 32
8 (005H)
8.625 ⁄ ⁄
————
219.1 M16 24
10
10.750
——
⁄ 1 ⁄
——
273.0 M22 36
12
12.750
——
⁄ 1 ⁄
——
323.9 M22 36
200A (JIS)
⁄ ⁄ ¾ 1 ¼
——
216.3 M16 24 M20 32
250A (JIS)
——
⁄ 1 ⁄
——
267.4 M22 36
300A (JIS)
——
⁄ 1 ⁄
——
318.5 M22 36
  • Page 1 1
  • Page 2 2
  • Page 3 3

Victaulic L080489XT0 Installation guide

Type
Installation guide
This manual is also suitable for

The Victaulic L080489XT0 is a 4" Style 489XT rigid coupling designed for use with Schedule 10 and 40 steel pipe. It features a one-piece EPDM gasket that provides a positive seal and eliminates the need for separate gaskets and sealants. The coupling is easy to install, requiring only a single wrench to tighten the nuts. It is also reusable, making it a cost-effective option for temporary or permanent installations. The L080489XT0 is ideal for use in a variety of applications, including water, wastewater, chemical, and mining.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI