Marantec Dynamic 735 Owner's manual

Brand: Marantec

Model: Dynamic 735

Category: Gate Opener

Type: Owner's manual

This manual is also suitable for

Operating Instructions

Dynamic 735-S, 740 FU-S

Operator system for Sliding Gates

2 Operating instructions, Dynamic 735-S, 740 FU-S GB (#100465)
2. Table of contents
1. Meaning of symbols  . . . . . . . . . . . . . . . . . . . . . . . . .2
2. Table of contents  . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
3. General safety advice  . . . . . . . . . . . . . . . . . . . . . . . .3
4. Product overview  . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
4.1 Dynamic 735-S, 740 FU-S supply package  . . . . .4
4.2 Dimensions  . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
4.3 Gate variations  . . . . . . . . . . . . . . . . . . . . . . . . .5
5. Preparation for mounting  . . . . . . . . . . . . . . . . . . . . .5
5.1 General notes  . . . . . . . . . . . . . . . . . . . . . . . . . .5
5.2  Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
5.3 Gate and foundation layout . . . . . . . . . . . . . . . .6
5.4 Cabling layout  . . . . . . . . . . . . . . . . . . . . . . . . . .7
6. Installation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
6.1  Installing the motor unit  . . . . . . . . . . . . . . . . . .7
6.2 Mounting the toothed rack . . . . . . . . . . . . . . . .9
6.3 Adjusting the height of the motor unit  . . . . . .11
6.4 Connection of control elements . . . . . . . . . . . .11
7. Initial operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
7.1 Motor unit cabling . . . . . . . . . . . . . . . . . . . . . .12
7.2 Cabling for the Control x.plus control unit . . . .15
7.3 Connecting the power supply  . . . . . . . . . . . . .19
7.4 Overview of the Control x.plus control unit . . .24
7.5 Express programming  . . . . . . . . . . . . . . . . . . .24
7.6 Changing the rotational direction  . . . . . . . . . .27
7.7 Check the system  . . . . . . . . . . . . . . . . . . . . . .28
8. Operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
8.1 Standard operation  . . . . . . . . . . . . . . . . . . . . .29
8.2 Release mechanism  . . . . . . . . . . . . . . . . . . . . .30
9. Extended operator functions  . . . . . . . . . . . . . . . . .31
9.1 General notes on extended operator functions 31
9.2 Programming structure for extended operator
functions (Example for Level 2, Menu 2)  . . . . .32
9.3 General overview of the programmable 
functions   . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
9.4 Functions overview for the levels  . . . . . . . . . . .34
10. Messages  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
10.1 Overview of the display functions  . . . . . . . . . .44
10.2 Status messages . . . . . . . . . . . . . . . . . . . . . . .44
10.3  Fault messages  . . . . . . . . . . . . . . . . . . . . . . . .45
10.4 Flow chart showing fault messages for control
units with keypad on cover and key switch . . .46
10.5 Rectifying faults  . . . . . . . . . . . . . . . . . . . . . . . .47
11. Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
11.1 Technical data for Dynamic 735-S, 740 FU-S  . .49
11.2 Declaration of Incorporation  . . . . . . . . . . . . . .50
11.3 EC Declaration of Conformity  . . . . . . . . . . . . .51
1. Meaning of symbols
Caution! 
Danger of personal injury!
The following safety advice must be observed
at all times so as to avoid personal injury!
Attention! 
Danger of material damage!
The following safety advice must be observed
at all times so as to avoid material damage!
Advice / Tip
Check
Reference
i
Advice
Type plate on motor unit
Type: ____________________________________________________
Art. No.: _________________________________________________
Product No.: ______________________________________________
Type plate on control unit
Type: ____________________________________________________
Art. No.: _________________________________________________
Product No.: ______________________________________________

Operating instructions, Dynamic 735-S, 740 FU-S GB (#100465) 3

Beside the advice in these instructions, please observe the general

safety and accident prevention regulations!

Our sales and supply terms and conditions are effective.

Information on installing the operator system

• Ensure that the gate is in good mechanical condition.

• Ensure that the gate can stop in any position.

• Ensure that the gate can be easily moved in the OPEN and CLOSE

directions.

• Ensure that the gate opens and closes properly.

• Remove all unnecessary components from the gate (e.g. cables, chains,

brackets).

• Render any installations inoperable that will no longer be needed after

the operator system has been installed.

• Before commencing cabling works it is very important to disconnect the

operator system from the electricity supply.

Ensure that the electricity supply remains disconnected throughout the

cabling works.

• Adhere to the local protection regulations.

• Lay the electricity supply cables and control cables; these MUST be laid

separately. The controls voltage is 24 V DC.

• Install the operator system with the gate in the CLOSED position.

• Install all the impulse transmitters and control devices (e.g. remote

control buttons) within sight of the gate and at a safe distance from the

moving parts of the gate. A minimum installation height of 1.5 m must

be observed.

• Ensure that no part of the gate extends across public footways or roads

when the installation is complete.

Information on commissioning the operator system

After initial operation, the persons responsible for operating the gate

system, or their representatives must be familiarised with the use of the

system.

• Make sure that children cannot access the gate control unit.

• Before moving the gate, make sure that there are neither persons nor

objects in the operating range of the gate.

• Test all existing emergency command devices.

• Never insert your hands into a running gate or moving parts.

• Pay attention to any parts of the gate system that could cause crushing

or shearing damage or accidents.

The EN 13241-1 regulations must be observed.

Information on servicing the operator system

To ensure proper operation, the following items must be checked

regularly and repaired if necessary. Before any works to the gate system

are undertaken, the operator system must be disconnected from the

mains.

• Check once a month that the operator system stops and reverses in

every position when the gate touches an obstacle. Place an obstacle in

the path of the gate to check this.

• Check the settings of the OPEN and CLOSE automatic cut-out function.

• Check all movable parts of the gate and operator system.

• Check the gate system for signs of wear or damage.

• Check whether the gate can be easily moved by hand.

Information on cleaning the operator system

Never use water jets, high pressure cleaners, acids or bases for cleaning.

Please read carefully!

IMPORTANT SAFETY INSTRUCTIONS:

IMPORTANT - PLEASE OBSERVE ALL SAFETY INSTRUCTIONS TO PREVENT

INJURY TO PERSONS.

PLEASE KEEP THESE INSTRUCTIONS FOR FURTHER USE.

IMPORTANT INSTRUCTIONS FOR SAFE INSTALLATION:

IMPORTANT - INCORRECT INSTALLATION CAN RESULT IN SERIOUS INJURY.

PLEASE FOLLOW ALL INSTALLATION INSTRUCTIONS.

Target group

This operator system may only be installed, connected and put into

operation by qualified and trained professionals!

Qualified and trained specialist personnel are persons

- who have knowledge of the general and special safety regulations,

- who have knowledge of the relevant electro-technical regulations,

- with training in the use and maintenance of suitable safety equipment,

- who are sufficiently trained and supervised by qualified electricians,

- who are able to recognise the particular hazards involved when working

with electricity,

- with knowledge regarding applications of the EN 12635 standard

(installation and usage requirements).

Warranty

For an operations and safety warranty, the advice in this instruction

manual has to be observed. Disregarding these warnings may lead

to personal injury or material damage. If this advice is disregarded, the

manufacturer will not be liable for damages that might occur.

Batteries, fuses and bulbs are excluded from warranty.

To avoid installation errors and damage to the gate and operator system,

it is imperative that the installation instructions are followed. The system

may only be used after thoroughly reading the respective mounting and

installation instructions.

The installation and operating instructions are to be given to the gate

system user, who must keep them safe. They contain important advice for

operation, checks and maintenance.

This item is produced according to the directives and standards

mentioned in the Manufacturer's Declaration and in the Declaration of

Conformity. The product has left the factory in perfect condition with

regard to safety.

Power-operated windows, doors and gates must be checked by an expert

(and this must be documented) before they are put into operation and

thereafter as required, but at least once a year.

Correct use

The operator system is designed exclusively for opening and closing

sliding doors and gates.

Gate requirements

The Dynamic 735-S operator system is suitable for:

- Sliding gates weighing up to 1,300 kg.

The Dynamic 740 FU-S operator system is suitable for:

- Sliding gates weighing up to 1,800 kg.

The gate must have:

- mechanical gate stops in both directions,

- a straight and even travel path, i.e. with absolutely no slope.

3. General safety advice

4.2 Dimensions

4 Operating instructions, Dynamic 735-S, 740 FU-S GB (#100465)

4.1 Dynamic 735-S, 740 FU-S supply package

4. Product overview

1 Motor unit (M6) Dynamic 735-S, 740 FU-S

2 Key

3 Wall plug set for mounting on foundation (ø18)

Standard package

4.1 / 1

In addition to the components in the standard package, the

following is required for the installation:

- toothed rack

4.2 / 1

404

264

498

148

Dynamic 735-S, 740 FU-S

Operating instructions, Dynamic 735-S, 740 FU-S GB (#100465) 5

5.1 General notes

The pictures in these instructions are not true-to-scale.

Dimensions are always given in millimetres (mm)!

The motor can be mounted on the right or left hand side of the

gate depending on the direction of opening.

These instructions show the motor being installed on the right

hand side.

If installed on the left-hand side, the rotational field for the motor

must be adapted accordingly.

5. Preparation for mounting4. Product overview

4.3 / 1

The standard supply package is suitable for

the following types of gate.

Gate system on rails

4.3 / 2

Cantilevered gate system

1/1

4.3 Gate variations

Attention!

In order to guarantee correct mounting, carry

out the following checks before installing.

Supply package

• Check the package to ensure that all the parts are included.

• Check that you have all the additional components that are

necessary for your particular installation requirements.

Foundations

• Check the proposed installation location for the operator

system:

- The motor unit should not be installed within the clear

width (r)!

- For cantilevered gates, the motor unit must be mounted at

the mid point between the carrier roller assemblies.

- The foundations must be suitable for heavy-duty wall plugs.

• Check whether the existing foundations are suitable.

• Check the supply cable.

Pay particular attention to the cable exit point where the motor

unit is to be installed.

Gate system

• Ensure that your gate system has an appropriate electricity

supply connection and a facility for disconnecting the mains.

• Ensure that all cables are suitable for outdoor use (UV resistant

and cold resistant).

• Install both OPEN and CLOSED gate positions with a mechanical

door limit stop. Choose the position in such a manner that the

closing edge in the OPEN position and the CLOSED position will

not be pushed in or activated.

• Take measures to safeguard any crushing or shearing zones in

the gate system.

• Check that the gate to be operated fulfils the following

conditions:

- The travel path of the gate must be horizontal, i.e. on no

account sloping.

- When closed, the gate should extend at least 500 mm further

than the clear width on the installation side.

- The gate must have a mechanical gate stop for both

directions.

- The gate itself must be straight, so that the distance between

the motor unit and the gate never changes.

5. Preparation for mounting

A Empty conduit for control cable

B Empty conduit for electricity supply cable

q Gate width

r Clear width

s Opening direction

t Below depth of frost penetration

x Gate thickness + distance from structure

5.3 Gate and foundation layout

5.3 / 1

260

6 Operating instructions, Dynamic 735-S, 740 FU-S GB (#100465)

5.2 Checks

5.4 / 1

3 x 1.5 mm

230 V AC /

5 x 2.5 mm

400 V

2 x 0.4 mm

1 Signal transmission system

2 Key switch / Special 750

3 Signal light

4 Closing edge safety device (CESD)

5 Mains isolator switch (mains disconnection facility)

6 Photocell

Advice:

This is just an example of a cabling layout; the

layout can vary according to the type of gate

and the associated equipment.

Reference:

For the installation and cabling of the gate sen-

sors, control elements and safety equipment,

the relevant installation instructions must be

observed.

5. Preparation for mounting

6.1 Installing the motor unit

• Remove the motor unit cover.

Attention!

To install the motor unit correctly, the following

points must be assured:

- The motor unit console must be aligned to

face the gate, so that the spur gear can mesh

with the toothed rack whatever the position

of the gate.

- The wall plugs for the floor console must be

at least 150 mm from the edge of the

foundations.

- After completing the installation and commis-

sioning work, all the covers must be reat-

tached to the motor unit.

6.1 / 1

Attention!

To install the motor unit correctly, it must be

mounted at the mid point between the carrier

roller assemblies if the gates are cantilevered.

6. Installation

5.4 Cabling layout

Operating instructions, Dynamic 735-S, 740 FU-S GB (#100465) 7

Reference:

Section 6.2.4 describes the procedure for

aligning the motor unit.

6. Installation

6.1 / 2

404

360

150

176

180

C Wall

D Gate

E Mounting surface for the toothed rack

F Empty conduit for power supply cable / control cable

G Foundations

H Front edge of the existing toothed rack

r Clear width

• Calculate the distance from the mounting surface for the

toothed rack (E) to the motor unit, taking into account

dimension X.

Special 475: X = 100

Reference:

When determining the mounting surface for

the toothed rack, the information given in

Section 6.2.2 must be observed.

Reference:

The height adjustment of the motor unit is

described in Section 6.3.

• Before installing the motor unit, check whether the possible

height adjustment of the motor unit (approx. 50 mm) is

sufficient for the situation on site, or whether the motor unit

needs to be raised on a backplate.

• Align the floor console parallel to the gate.

Advice:

When using an existing toothed rack, the cor-

rect dimension is 70 mm from the first screw to

the front edge of the toothed rack.

• Drill the holes for the wall plugs as shown in the drill pattern

provided.

• Insert the wall plugs and screw them tight.

• Feed the supply cable (J) through the opening in the floor

console.

• Align the motor unit.

6.1 / 3

Caution!

Danger of electric shock:

Before commencing cabling works it is very

important to disconnect the operator system

from the electricity supply. Ensure that the elec-

tricity supply remains disconnected for the

duration of the cabling works (e.g. prevent

reconnection).

Attention!

- In order to install the motor properly, the

foundations must be fully hardened before

the mounting plugs or screw anchors can be

inserted.

- To maintain the specified protection category

of the operating system,

- the openings must be sealed using the

correct gaskets,

- the cables must lie correctly in the cable

inlets,

- the plug-in cable inlets must be correctly

connected to the control unit.

95 – 100

8 Operating instructions, Dynamic 735-S, 740 FU-S GB (#100465)

150

260

• Screw down the motor unit.

6.2 Mounting the toothed rack

Attention!

To install the rack correctly, the following must

be ensured:

- The motor unit has been mounted.

- The motor unit is unlocked (released).

6.2.1 General

Reference:

- For gates with an existing toothed

rack, please skip to Section 6.3.

- Section 8.2 describes how to release the

motor unit.

Minimum length of toothed rack

The minimum length of the toothed rack is equal to the

movement stroke of the gate between the gate OPEN and gate

CLOSED positions + 180 mm.

6. Installation

6.2.2 / 1

Attention!

To ensure trouble-free movement of

the gate, the following points must be assured:

- The screws (A) should not obstruct the opera-

tion of the gate (e.g. by extending into the

path of the gate rollers (B)).

- The spur gear (C) should not rest against the

gate.

- The spur gear (C) should not be at its lowest

possible position (it must be possible to lower

the spur gear by 1 to 2 mm after the toothed

rack assembly has been installed).

• Determine the installation height of the toothed rack on the

gate.

• Adjust the height of the spur gear accordingly.

Advice:

The toothed rack can be adapted to fit the gate

by means of a backplate (D).

6.2.2 Determining the installation height

Reference:

The height adjustment for the motor unit is

described in Section 6.3.

190 – 240

Operating instructions, Dynamic 735-S, 740 FU-S GB (#100465) 9

6.2.4 Adjust the motor unit

Attention!

To ensure that the gate runs smoothly, it is

important

- that a gap of 1 to 2 mm is maintained

between the toothed rack and the spur gear,

- that the gear wheel engages with the toothed

rack along its entire length.

6.2.4 / 1

1 – 2

The height of the spur gear must therefore be readjusted.

• Lower the spur gear by 1 to 2 mm.

Reference:

Section 6.3 describes how to adjust the height

of the motor unit.

10 Operating instructions, Dynamic 735-S, 740 FU-S GB (#100465)

6. Installation

Maximum length of toothed rack

If a toothed rack is to be installed across the entire width of the

gate, then the installation position does not have to be

determined.

Minimum length of toothed rack

The minimum length of toothed rack must be determined at the

gate.

• Move the gate to the OPEN position.

• Make a mark on the gate:

90 mm from the centre of the spur gear in the direction of

closing.

6.2.3 Determining the installation position and the length

of the toothed rack

• Move the gate to the CLOSED position.

• Make a mark on the gate:

90 mm from the centre of the spur gear in the direction of

opening.

6.2.3 / 1

6.2.3 / 2

6.2.3 / 3

Attention!

To ensure trouble-free operation,

the toothed rack must at least extend across

the area (E) between the markings.

Reference:

When installing the toothed rack, the relevant

instructions must be followed.

Operating instructions, Dynamic 735-S, 740 FU-S GB (#100465) 11

6. Installation

6.3 / 1

< 50

It is possible to adjust the height of the motor unit.

• Loosen the screws.

• Adjust the motor unit to the appropriate height.

• Tighten the screws.

6.4 Connection of control elements

Reference:

For the control unit cabling, the relevant

instructions must be followed.

6.3 Adjusting the height of the motor unit

6.4 / 1

• Using a step drill, open up the corresponding cable inlet.

• Close the inlet using the corresponding screw fitting.

Creating further cable inlets

It is only necessary to create further cable inlets if additional

systems are to be connected to the control unit.

Advice:

If necessary, the housing must be removed to

allow the cable inlet hole to be opened up.

Label Type / function

Positioning box

(EPM = Electronic Positioning

Module)

–

EPM stand-by mode indicator

(LED off)

–

C Operating indicator (EPM) –

D PE connection 7.3

HQ10

Operating voltage indicator for

operator system

7.3 / 2

XB40

Connection of Control x.plus

control unit

7.2

XH19

Connection of signalling devices

Programmable relay output

7.1 / 5

9.4, Level 1,

Menu 7

XM81A Connection of motor 7.3

XM81B Connection of motor, delta mode 7.3.4

XM89 Connection of brake –

XN81A Connection of mains cable 7.3

XN81B Connection for mains routeing –

XP10

For connection of door sensors

(safety circuit SC)

7.2 3

XV30

Connection for RPM sensor

(on the motor side)

–

XV31 Connection for positioning box –

7.1 / 2

Control unit

Control x.plus 3-phase model

XP10

XB40

XV31

XV30

HQ10

XM81B

XN81A

XN81B

XM81A

XM89

XH19

7.1 Motor unit cabling

• Loosen the screws on the housing cover.

• Remove the housing cover.

7.1 / 1

Preparation

Attention!

- To avoid damage, it is essential that the

following points be observed:

- The local protection regulations are to be

complied with at all times.

- - The mains cables and control cables MUST

be laid separately.

- To maintain the specified protection category

of the operating system, the cables must be

fitted with the correct gaskets.

Caution!

Danger of electric shock:

Before cabling works commence, a check must

be carried out to ensure that the cables are at

zero voltage.

Measures must be taken to ensure that the

cables remain dead for the duration of the

works (e.g. prevent the power supply from

being switched back on).

12 Operating instructions, Dynamic 735-S, 740 FU-S GB (#100465)

7. Initial operation

Operating instructions, Dynamic 735-S, 740 FU-S GB (#100465) 13

7. Initial operation

7.1 / 3

Control unit

Control x.plus frequency converter (FU) model

Label Type / function

Positioning box

(EPM = Electronic Positioning

Module)

–

EPM stand-by mode indicator

(LED off)

–

C Operating indicator (EPM) –

D PE connection 7.3

HQ10

Operating voltage indicator for

operator system

7.3 / 2

XB40

Connection of Control x.plus

control unit

7.2

XH19

Connection of signalling device

Programmable relay output

7.1 / 5

9.4, Level 1,

Menu 7

XN81A Connection of mains cable 7.3

XN81B Connection for mains routeing –

XN85

Connection for frequency

converter (FU)

–

XP10

For connection of door sensors

(safety circuit SC)

7.2.3

XV30

Connection for RPM sensor

(on the motor side)

–

XV31 Connection for positioning box –

XW01

Connection for frequency

converter (FU) control cable

–

XP10

XB40

XV31

XV30

HQ10

XN85

XN81A

XH19

XN81B

XW01

14 Operating instructions, Dynamic 735-S, 740 FU-S GB (#100465)

-XH19

-HH94

H1 92 94

7.1 / 6

Connection for signal light

Designation Type / function

HH94 Signal light supplied by customer

XH19 Connection of signalling device

XN81B Connection for mains routeing

M06E047

NH192

-XN81B

-HH94

-XH19

7.1 / 7

M06E047

Reference:

Safety devices are deactivated in the Reset

menu (Section 9.4 / Level 1 / Menu 8).

Advice:

A defective or removed safety device must be

deactivated.

• Insert the plug of the devices to be connected into socket

XH19.

7.1 / 5

Connection of signal device

Signal lights are not included in the operator system supply

package.

Attention!

- To avoid damage being caused to the circuit

board, the contact loading (max. 230 V / 2 A)

must be observed.

- In the case of low voltage, the connection

cable must be double-insulated.

XH19

7.1 / 4

8 - 9

7. Initial operation

Operating instructions, Dynamic 735-S, 740 FU-S GB (#100465) 15

Attention!

- To avoid damage to the cabling, care must be

taken not to trap the cables when closing the

cover.

- To maintain the specified protection category

of the operator system:

- the inlet openings must be fitted with

suitable cable gaskets,

- - the cables must lie correctly in the cable

inlets.

• Place the housing cover on the motor unit.

• Screw the housing cover to the motor unit.

7.1 / 8

7. Initial operation

7.2 Cabling for the Control x.plus control unit

7.2.1 Preparation

Attention!

- To avoid damage, it is essential that the

following points be observed:

- The local protection regulations are to be

complied with at all times.

- - The mains cables and control cables MUST

be laid separately.

- To maintain the specified protection category

of the operating system, the cables must be

fitted with the correct gaskets.

Caution!

Danger of electric shock:

Before cabling works commence, a check must

be carried out to ensure that the cables are at

zero voltage.

Measures must be taken to ensure that the

cables remain dead for the duration of the

works (e.g. prevent the power supply from

being switched back on).

• Loosen all six screws on the housing cover.

• Swivel all six screws away from the cover.

• Open the housing cover out to one side.

7.2.1 / 1

Advice:

The screws need not be removed in order to

open the housing cover.

16 Operating instructions, Dynamic 735-S, 740 FU-S GB (#100465)

-XB50

- SB7

1413

- SB6

1413

-SB5

1211

- SB3

1413

B5 5 6 7 3

7.2.2 / 2

Designation Type / function

SB3 Operating button for intermediate position OPEN

SB5 Operating button for STOP

SB6 Operating button for OPEN

SB7 Operating button for CLOSE

Connection of external control elements (XB50)

M06E045

-XB53

- SB3 4

1211

+B5 -34

24V+--

7.2.2 / 3

Designation Type / function

24V + 24 V DC

- GND

SB34

Potential-free normally closed contact for closing

prevention device

Connection for closing prevention device (XB53)

Advice:

- To enable the “automatic closing timer”

function to be programmed, one of the

following two elements must be connected:

- a closing prevention device at terminal XB53,

- - a photocell barrier at terminal XP62A/B.

- If a closing prevention device is connected, it

will be recognised when the mains supply is

switched on.

- A device that is faulty or has been removed

must be deactivated.

M06E045

MDS Marantec Diagnostic System

XB50/ Supplied with shorting jumper in place

XB11

7.2.2 / 1

Designation Type / function

SB59 Programming switch (ON/OFF)

7.5.1

9.1

XB11

For connection of command

device

–

XB40

For connection of Control x.plus

control unit

7.1 / 2

7.1 / 3

XB41

For connection of expansion

modules

–

XB42

Terminal

Radio receiver

–

XB43 For connection of MDS module –

XB50

For connection of external control

elements

7.2.2 / 2

XB53

For connection for closing

prevention device

7.2.2 / 3

XB90

For connection of programmable

impulse input

7.2.2 / 4

XB42

XB43

SB59

XB90XB53XB50

XB41

OFF

7.2.2 Connection of Control x.plus control unit

Advice:

Programming can be disabled with switch

SB59.

ON Programming enabled

OFF Programming disabled

XB11

XB40

7. Initial operation

Operating instructions, Dynamic 735-S, 740 FU-S GB (#100465) 17

Reference:

Safety devices and closing protection devices

are deactivated in the Reset menu (Section 9.4 /

Level 1 / Menu 8).

-XB90

B9 8

-SB8

1413

7.2.2 / 4

For connection of programmable impulse input (XB90)

Designation Type / function

SB8 Impulse button (programmable)

9.4 /

Level 5 /

Menu 1

M06E045

7. Initial operation

Designation Type / function

XP10

For connection of Control x.plus

control unit

–

XP27

For connection of photocell

expander circuit board

–

XP41 For connection of safety circuit, SC –

XP62A

For connection of first photocell

(2-wire design)

7.2.3 / 3

XP62B

For connection of second

photocell (2-wire design)

(only with photocell expander

circuit board)

7.2.3 / 4

XP15

For connection of gate sensor

Safety circuit

Closing edge safety device

CLOSED (optosensor 1 or

8k2 contact strip)

–

XP516

For connection of contact strip

OPEN

–

7.2.3 / 1

7.2.3 Connection of safety device

XP41

XP516

XP10

XP15

XP62B

XP62A

XP27

XP27 The unit is delivered with the jumper in the position

shown.

XP41 Delivered with the shorting jumper in place.

If this terminal is used, the shorting jumper must be

removed.

18 Operating instructions, Dynamic 735-S, 740 FU-S GB (#100465)

• Insert the plug of the cable loom into socket XP10A (blue plug).

All connected and operational safety devices are recognised

automatically.

Reference:

Safety devices are deactivated in the Reset

menu (Section 9.4 / Level 1 / Menu 8).

Advice:

- A defective or removed safety device must be

deactivated.

- Once a safety element has been connected up

and is fully functional, it can only be deacti-

vated by a reset after it has been removed

from the connection it was attached.

For connection of photocell (XP62A and XP62B)

For the connection of further systems it may be necessary to

extend the number of cable inlets in the control unit.

Reference:

Increasing the number of the cable inlets is

described in Section 6.4.

7.2.3 / 3

XP62A

7.2.3 / 4

M07E054

Designation Type / function

XP62A For connection of first photocell

XP62B

For connection of second photocell

(only with photocell expander circuit board)

7. Initial operation

7.2.3 / 2

Designation Type / function

H1 Red LED * - closing edge safety device 1 CLOSED

H4 Red LED * - closing edge safety device 1 OPEN

H7 Green LED - power supply

H8 No function

H9 Flashing yellow LED - communication to control

* LEDs only indicate status if closing edge safety device is

connected (light up if working, flash if closing edge safety

device is interrupted)

Operating instructions, Dynamic 735-S, 740 FU-S GB (#100465) 19

Reference:

Express programming is described in Section 7.5.

Check:

When the controls are supplied by the mains

voltage, the indicator HQ10 should light up

green.

Advice:

For an unprogrammed control unit (first time

installation), the start display for express

programming is shown.

7.3 Connecting the power supply

Attention!

To guarantee correct operation of the

operator system,

- the system must be connected to a technically

sound power supply network that is protected

with a 16 A fuse;

- the voltage and frequency must correspond to

those specified on the identification plate;

- for the 3-phase motor model, a clockwise

rotating field must be provided right up to the

connection of the controls;

- if fixed cabling is used, an all-pole mains

isolator switch must be used.

7.3 / 1

• Connect the mains plug of the operator system to an available

mains socket near the door.

Caution!

Danger of electric shock:

Before cabling works commence, a check must

be carried out to ensure that the cables are at

zero voltage.

Measures must be taken to ensure that the

cables remain dead for the duration of the

works (e.g. prevent the power supply from

being switched back on).

• Close the housing cover.

• Swivel all six screws into place above the housing cover.

• Screw the housing cover tight.

7.2.3 / 5

Attention!

- To avoid damage to the cabling, care must be

taken not to trap the cables when closing the

cover.

- To maintain the specified protection category

of the operator system

- the inlet openings must be fitted with

suitable cable gaskets,

- - the cables must lie correctly in the inlets,

- - the plug-in cable inlets must be

correctly connected to the control unit.

7. Initial operation

20 Operating instructions, Dynamic 735-S, 740 FU-S GB (#100465)

7.3 / 2

HQ10

Advice:

A fixed connection must be made if a higher

protection category is required on site than can

be provided by a mains plug connection.

The motor unit must conform to the

requirements of the protection category.

7.3.2 / 1

• Open the operator control unit.

7.3.2 Control x.plus frequency converter (FU) model

(1N~, 230 V)

7.3.2 / 2

• Connect the leads to terminal block XN81A.

XN81A

XN85

Terminal XN81A must be connected to the power supply system

with fixed cabling.

7. Initial operation

Page is loading ...

Marantec Dynamic 735 Owner's manual

Brand: Marantec

Model: Dynamic 735

Category: Gate Opener

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Marantec Dynamic 735 Owner's manual

This manual is also suitable for

Marantec Dynamic 735 Owner's manual

Related papers

Other documents