Wren Tower Unit Assembly Manual

For Internal Use: FI.WR.INS.093_WKIN00220_TOWER_Feature_Aperture_Assembly_Rev1.indd

Built-in 2070 x 600

Built-in 2250 x 600 Tall

TOWER UNIT

600 Feature Units

Open Shelf

Wine Rack

Plate Rack

Assembly Guide

TOWER UNIT

600 Feature Units

Open Shelf

Wine Rack

Plate Rack

Assembly Guide

For Internal Use: FI.WR.INS.093_WKIN00220_TOWER_Feature_Aperture_Assembly_Rev1.indd

Page 1

BEFORE YOU START

INSTALLATION

SHOULD BE

PERFORMED BY A

COMPETENT

PERSON ONLY.

THIS PRODUCT COULD

BE DANGEROUS

IF INCORRECTLY

INSTALLED

Top Unit (C)

x1

Size example ONLY

Mid Unit (B)

x1

Size example ONLY

Base Unit (A)

x1

Size example ONLY

REQUIRED TOOLS

NOT to be used

with CAM DOWEL

& CAM LOCK

Hanging Bracket

x2 Inc Screws

Hanging Bracket Plate

x2 (Screws NOT included)

Hinge Mounting Plate

x2 Inc Screws

Feature Unit Fitting Pack may vary in accordance to

Specic Customer Kitchen Plan

Base Unit Fitting Pack contents may vary in

accordance to Specic Customer Kitchen Plan

Corner

Gusset

x2

Hanging Bracket

Cover Cap

x2

Prior to installation, xtures including doors, drawers and loose

shelves should be removed to ensure a safe installation. Use

Wren provided DoorSafe for temporary storage.

(L) x8

15mm

Screw

(L) x16

15mm

Screw

(S) x4

20mm

Screw

(K) x4

30mm

Screw

(K) x4

30mm

Screw

(M) x4

Cover

Caps

(ZZ) x8

Metal Shelf

Pegs

(ZZ) x8

Metal Shelf

Pegs

DoorSafe

Supplied

with:

Supplied

with:

Supplied

with:

x1

Space Plug

(N) x1

Door

Buer

(K) x7

30mm

Screw

(L) x28

15mm

Screw

(M) x4

Cover

Cap

(F) x12

Wooden Dowel

(G) x8

Cam Dowel

(Expanding)

(H) x8

Cam Lock

x5

Legs

TOWER UNIT

600 Feature Units

Open Shelf

Wine Rack

Plate Rack

Assembly Guide

For Internal Use: FI.WR.INS.093_WKIN00220_TOWER_Feature_Aperture_Assembly_Rev1.indd

Page 2

Step 1.

Secure each of the legs into place onto base unit (A) with

2 x 15mm screws (L) per leg.

Step 3.

Push leg rmly down into leg base.

Adjust legs to 155mm before turning carcass

upright. Once in situ level accordingly.

Step 2.

Lightly hit centre peg of leg

base with hammer until ush.

Leg position diagram

Front

Base Unit A

Ensure legs are rotated as shown, ensuring

support of adjoined panels at both sides.

Front legs should have at edge to the front.

L

TOWER UNIT

600 Feature Units

Open Shelf

Wine Rack

Plate Rack

Assembly Guide

For Internal Use: FI.WR.INS.093_WKIN00220_TOWER_Feature_Aperture_Assembly_Rev1.indd

Page 3

B

A

Step 4.

Position Feature Unit (B) onto

secured Base (A) with an 18mm

overhang, as shown.

Step 5.

Using 2x 30mm Screws (K) screw up through the

front rail of base unit (A) to secure both units

Base (A) & Feature unit (B) together. Screws

should be equally spaced, as shown.

18mm

K

Screw into any side units using the 30mm screws (K) provided to secure

to the unit. Screw just to the rear of the hinge mounting plate at the top

and bottom of both sides of the unit, place a cover cap (M) on the head

to conceal it.

Secure base unit (A) to wall using space plugs (G). Drill 2 pilot holes

through the back brace into the wall and insert wall plugs. Then unwind

space plug until it contacts both surfaces. Finally, tighten the screws.

Screws for attaching to walls are not provided as these vary

depending on your wall material and construction.

Ensure appropriate xings for

wall construction are used.

K

Front

Mid Unit

B

Base Unit

A

View from back of unit

TOWER UNIT

600 Feature Units

Open Shelf

Wine Rack

Plate Rack

Assembly Guide

For Internal Use: FI.WR.INS.093_WKIN00220_TOWER_Feature_Aperture_Assembly_Rev1.indd

Page 4

Step a

Insert Hanging

Bracket into pre-drilled holes

Step 6.

Hanging Brackets steps a,b & c to be carried out on both

sides of Top Unit (C) as shown.

Step c

Secure with provided

2 x 20mm screws (S) per bracket

Step b

Rotate locking

lever 180 degrees

S

Detail A

Step 7.

Secure Corner

Gussets to the

bottom left and right

hand side of the wall

unit using 4 x 15mm

screws (L) per plate.

L

Detail B

B

A

Step 8.

Drill a small pilot hole through the centre of the Corner Gussets.

Use this hole at the end of the process to screw through and

into the wall. Cover the screw heads using the

cover caps (M) provided.

Screws for xing to walls are not provided as these vary

depending on your wall material and construction. Ensure

appropriate xings for wall constructions are used.

Pilot

hole

M

Detail B

View through

back panel

Top Unit C

Care to be taken. Hanging procedure

is neccesary for a safe installation.

TOWER UNIT

600 Feature Units

Open Shelf

Wine Rack

Plate Rack

Assembly Guide

For Internal Use: FI.WR.INS.093_WKIN00220_TOWER_Feature_Aperture_Assembly_Rev1.indd

Page 5

Step 9.

Measure appropriately and attach the 2 x hanging bracket plates onto the

wall screwing through the provided holes into your wall.

Screws for xing to walls are not provided as these vary depending

on your wall material and construction. Ensure appropriate xings for

wall construction are used.

Step 10.

Hang the cabinet using

the brackets to hook

onto the plate as shown.

Hanging Bracket

Plate

Step 11.

Using points a, b & c adjust the Cabinet to suit.

Step a.

Rotate the screw clockwise

to move the cabinet up.

Anti-clockwise for down.

Step b.

Adjust the depth

using centre

screw.

Step c.

Screw the red screw until it

touches the plate to lock

in position.

Hanging

Bracket

viewed though

Back Panel

b

C c

a

b

K

Step 12.

Screw into any side units using the

provided 2x 30mm screws (K) to

secure the unit. Screw just to the

rear of the hinge plate then place a

cover cap on the head to conceal it.

TOWER UNIT

600 Feature Units

Open Shelf

Wine Rack

Plate Rack

Assembly Guide

For Internal Use: FI.WR.INS.093_WKIN00220_TOWER_Feature_Aperture_Assembly_Rev1.indd

Page 6

Base Unit

A

Mid Unit

B

Top Unit

C

Step 13.

Using 2x 30mm Screws (K) screw up through the top of Feature

Unit (B) to secure it in place with Top Unit (C) as shown.

Screws should be equally spaced, as shown.

K

Ensure that screw is positioned

beneath Top Unit (C).

18mm

Top Unit

C

Mid Unit

B

Front

TOWER UNIT

600 Feature Units

Open Shelf

Wine Rack

Plate Rack

Assembly Guide

For Internal Use: FI.WR.INS.093_WKIN00220_TOWER_Feature_Aperture_Assembly_Rev1.indd

Page 7

To adjust hinge using a screw

driver, tighten or loosen as

required at points 1 & 2.

Point 1 - left - right

Point 2 - side - side

1

2

DOOR

FRONTAL

ADJUSTMENT

To release door,

pull catch as shown,

to release hinge from

the hinge plate.

View on Inside of carcass

The soft-close should be adjusted

to suit the size of the door.

Larger doors require the soft-close

strength adjusting higher than

smaller doors, to account for the

dierence in weight. The soft-

close should also be adjusted

to personal preference of door

closure speed. Increasing the

strength reduces the speed of the

door closure & vice versa.

Door Adjustment

Doors supplied in accordance to Customer Specic Kitchen Plan.

To strengthen (+) soft-close,

Turn the lever clockwise,

as required.

To weaken (-) soft-close,

Turn the lever anti-clockwise,

as required.

Factory standard position.

The top and

bottom hinges

MUST be

adjusted to

the SAME

STRENGTH.

View from rear

View on side of drawer side

TOWER UNIT

600 Feature Units

Open Shelf

Wine Rack

Plate Rack

Assembly Guide

For Internal Use: FI.WR.INS.093_WKIN00220_TOWER_Feature_Aperture_Assembly_Rev1.indd

Page 8

Drawer Adjustment

Drawers supplied in accordance to Customer Specic Kitchen Plan.

Drawer Frontal Adjustment

View on side of drawer side

1

3

2a

2b

Screw point 1 as shown to

adjust drawer frontal

right & left.

Screw point 1 as shown to

adjust drawer frontal

right & left.

Screw point 2a

as shown to adjust

drawer frontal up & down.

Screw point 2a

as shown to adjust

drawer frontal up & down.

Tighten 2b

once in position.

Tighten 2b

once in position.

Releasing xing clip.

Screw point 3 whilst

applying downward

pressure as shown to

release.

Releasing xing clip.

Screw point 3 whilst

applying downward

pressure as shown to

release.

Drawer Frontal Adjustment

1

3

2a

2b

TOWER UNIT

600 Feature Units

Open Shelf

Wine Rack

Plate Rack

Assembly Guide

For Internal Use: FI.WR.INS.093_WKIN00220_TOWER_Feature_Aperture_Assembly_Rev1.indd

Page 9

TOWER UNIT

600 Feature Units

Open Shelf

Wine Rack

Plate Rack

Assembly Guide

For Internal Use: FI.WR.INS.093_WKIN00220_TOWER_Feature_Aperture_Assembly_Rev1.indd

Page 10

Wren Tower Unit Assembly Manual

This manual is also suitable for

Wren Tower Unit Assembly Manual

Related papers

Other documents