Page is loading ...
1-07
B;- PO 58719332/62
ASSEMBLY INSTRUCTIONS
Six Drawer Wide Roll Cart
#ξξξ52 - Medium Pine Finish
&86720(5ξ6(59,&(ξ$1'ξ5(3/$&(0(17ξ3$576ξ
)25ξ)$67(5ξ6(59,&(ξ21ξ3$576ξ25ξ+(/3ξξ3/($6(ξ*2ξ72ξ285ξ:(%6,7(ξ$7ξ:::ξ$'(3786ξ&20ξ
25ξ&$//ξ72//ξ)5((ξξξξξξξ$'(3786ξξξξξξξξξξξξξξξξξξ)25ξ$66(0%/<ξ48(67,216ξ
021ξ)5,ξξξξ$ξ0ξξ72ξξξ3ξ0ξξ(ξ6ξ7ξξξ&/26('ξ+2/,'$<6
,)ξ<28ξ&$//ξξ3/($6(ξ+$9(ξ21ξ+$1'ξ
x 352'8&7ξ1$0(ξ$1'ξ672&.ξ180%(5
x :+(1ξ$1'ξ:+(5(ξ7+(ξ81,7ξ:$6ξ385&+$6('
x 3ξ2ξξ180%(5ξ)520ξ7+(ξ%27720ξ2)ξ7+,6ξ3$*(
,)ξ:(ξ$5(ξ%86<ξ+(/3,1*ξ27+(5ξ&86720(56ξξ3/($6(ξ/($9(ξ<28ξ1$0(ξ$1'ξ180%(5
72ξ5(&(,9(ξ$ξ5(7851ξ&$//ξξ
<285ξ5(7$,/(5ξ0$<ξ$/62ξ3529,'(ξ6(59,&(ξ25ξ3$576ξ
+(/3)8/ξ29(5$//ξ
x 6$9(ξ7+(6(ξ,16758&7,21ξ6+((76ξ$1'ξ7+(ξ%2;ξ817,/ξ<28ξ$5(ξ6$7,6),('ξ:,7+ξ7+(ξ$66(0%/<ξ
x '2ξ127ξ*/8(ξ7+(ξ3$576ξ2)ξ7+(ξ81,7ξ72*(7+(5ξ81/(66ξ<28ξ+$9(ξ7(67('ξ7+(ξ$66(0%/<ξ),567ξ
x 3(5)250ξ7+(ξ$66(0%/<ξ21ξ$ξ&/($1ξ+$5'ξ685)$&(ξ86,1*ξ7+(ξ)/$77(1('ξ&$5721ξ25ξ$ξ72:(/
72ξ3527(&7ξ7+(ξ685)$&(ξ$1'ξ7+(ξ),1,6+ξ2)ξ7+(ξ81,7ξξξ'2ξ127ξ$66(0%/(ξ21ξ&$53(7ξ
9,6,7ξ:::ξ$'(3786ξ&20ξ72ξ5(*,67(5ξ<285ξ352'8&7ξ$1'ξ6((ξ7+(ξ
&203/(7(ξ$'(3786ξ/,1(ξξ5(*,675$7,21ξ,6ξ5(48,5('ξ)25ξ3$576ξ5(48(676ξ
7+$1.ξ<28ξ)25ξ<285ξ385&+$6(ξ$1'ξ:(/&20(ξ72ξ$'(3786ξξ
127,&(ξξ7+(ξ:5,77(1ξ,16758&7,216ξCONTAINED +(5(,1ξ$5(ξ&23<5,*+7('ξ
ξξξξξξξξξξξξξξξ
ξξξξξ
ξξξξξξξξξξ
ξξ,ξξ$ ξξ&,ξξξ,)ξξξξ,ξξξ,ξξξξξ),ξ'ξξξξξξξ$,&ξ, ξ$$,!(ξξξ&+,ξξ$ ξξ&ξξξ$ξ,
ξξξξξ,)ξξξ,ξ("ξξ&("ξ,ξξ$,ξξξ&$ξ, $ξξξξ,ξ"ξξξ$ξ,ξξξ,)ξξ&,ξξ+,ξξξξ,ξξξξ,ξξξξξ$ξξ$ξ,
ξξξ$ξ,ξξξ"ξξ&ξ"ξ$&ξξ$,ξ"ξ,ξ,ξξ&("ξξ, ξ+, "ξξ(ξ&,ξξ, "ξξ(ξξξξ,ξ("ξξ&("ξ,ξ"ξξ,ξξ&("ξξ,ξξ&ξ"ξξξξ,
ξξ,&ξξξ,ξ*&"ξ,ξξ"ξ,)ξ&ξ,ξ(",ξ"ξ)ξ", ξ#&$ξ,
ξ
ξ ξξ,($ξ,"ξξξ,)ξξξ,ξ"ξ)ξ"$,$ξξξ%ξ
ξξ ξξξ,ξ"ξ)ξ",$ξξξ$,ξ"ξ,ξξ&, ξξξ&ξξ,&ξ,ξξξ , "ξ&ξξ&,+ξ(",ξξξ&ξξ$,ξ"ξξ,ξξξξξξξξ,ξξξ"$,ξξξ,"ξ$ξξ(ξξ
ξξ ξξξξξ+,$ξξξξξ,ξ"ξ)ξ", ξ"&$,ξξξξξξξ&ξ,$ξξξ$,)ξξξ,$&ξ"ξξξ,+ξ(",ξξξ&ξξ$ξ
ξξξξξξξξξξξξξξξξξξ
ξξξξξξξ
*.ξG ξ (ξ[," >K[3)" ξ[I))ξ[ξ
ξW/([ C-ξ4[ξ7[ξ([ ξξξ)2ξQ"4[ξ
ξ4[ξξ3[ξ
Q44([ξ[ L-ξX+[4ξξ)08ξ[ξ ξ-)&[ξξ)(ξ4*7[ξ
ξξ
ξ*-ξξWξ7[ξξ43Oξ(ξ[ξ'([Wξξξ7F1ξ[
(ξ[ξ
ξ(ξ[
/ξ;ξ " (ξξ[ξ4ξξP[ξ/4ξ[ξ)ξ$43[ξ)([ξ
D4[ξξ4:ξ %[Eξ7ξ I ""ξ ξ33V14[
ξξξξξ
ξ
")I[ξ*/ ξ4ξ[ξ Q#9[(4H4/ξ ξ7[=U4[4J*4(34[ξ
ξ
ξξξW(ξ< )(ξ[ξξξξ(ξξ[ξ)/[ξξξ
ξξξ34(34ξ[
ξ[ξξ/4ξξK[ξξξ
ξξ
ξξξξ ξ334&Q"4ξ[ B&[ξ/ξξWξ43[ξ
Aξ(3*)-7ξ= )([ξ(ξ[Iξ/4N)$ (ξ[ξ
ξ)375[IUMξP[U4"*[YSX1[/ξ;ξ "4/[ξ
!44*[ξ7U4 /[*/ ξ43[ /4ξ3)(ξR"4ξ[ξ()Iξ[ξ
YSWξ ξ/4[ξ) ( (ξ[ξ=6ξ&[ ξξ4*@ξ[ξ
I 7P[?4[ξξM[(ξ"[3B*ξ[ξξ334&Q"[
ξξξ
ZξξξYTWξξ334&Q"4ξ[ξYSWξ3ξH4ξr
ξξξξξξξξξξξξξ
ξξξξξξ
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
2-07
NOTICE: 7+(ξ:5,77(1ξ ,16758&7,216
CONTAINED
+(5(,1ξ$5( &23<5,*+7('ξ
1
2
4
3
6
7
6X
9
10
8
8
9
10
11
A
Dowel
8.0 x 30mm
12
B
Screw
3.0 x 25mm
48
C
Screw
4.0 x 30mm
10
D
D
Drawer
Runner
12
E
(Ea) Caster and
(Eb) Caster Insert
Pair
04
Nail
1.5 x 19mm
28
TIP: DOWELS (PART A) VARY EVER SO SLIGHTLY.
IF A DOWEL (PART A) IS LOOSE
WE PREFER YOU CALL OUR TOLL FREE NUMBER
FOR ADDITIONAL DOWELS -
VS GLUING THE DOWEL.
IF YOU CHOOSE TO GLUE THE PARTS,
COMPLETELY TEST THE ASSEMBLY FIRST.
WE DO NOT SUPPLY GLUE.
1
TOP
2
RIGHT SIDE
3
4
LEFT SIDE
BACK PANEL
6
7
8
9
10
11
BACK CASTOR SUPPORT
FRONT CASTOR SUPPORT
DRAWER SIDE
DRAWER BACK
DRAWER BOTTOM
DRAWER FRONT
NOTICE: 7+(ξ:5,77(1ξ ,16758&7,216
CONTAINED
+(5(,1ξ$5( &23<5,*+7('ξ
3-07
1
8,0 x 30mm
A=12
D=12
A
2
A
A
D
D
D
D
D
PREPARE PARTS FOR ASSEMBLY
β’
PUSH THE DOWELS (PART A) INTO THE EDGES OF
THE FOLLOWING PARTS, AS SHOWN:
(PART 2) RIGHT SIDE
(PART 3) LEFT SIDE
(PART 6) BACK CASTOR SUPPORT
(PART 7) FRONT CASTOR SUPPORT
ATTACHING DRAWER RUNNERS:
β’
THE DRAWER RUNNERS (PART D) WILL STRETCH
SLIGHTLY AS YOU HAMMER THEM INTO PLACE.
β’
LINE UP THE PIPS IN DRAWER RUNNERS (PART D) TO
THE PRE-DRILLED HOLES IN THE RIGHT SIDE PANEL
(PART 2).
β’
EASE THE PIPS INTO THE HOLES BY TAPPING EACH
PIP DOWN HALF WAY. START ON ONE END, THEN
THE MIDDLE, THEN THE OTHER END.
β’
WHEN ALL 3 PIPS ARE HALF WAY DOWN AND THE
DRAWER RUNNER (PART D) IS STRETCHED, HAMMER
THE RUNNER ALL THE WAY DOWN UNTIL IT IS FLUSH
WITH THE RIGHT SIDE PANEL (PART 2).
β’
REPEAT THESE STEPS TO ATTACH THE DRAWER
RUNNERS (PART D) TO THE LEFT SIDE (PART 3).
PREPARE CASTER SUPPORTS:
D
A
A
3
D
D
D
D
D
1st
2nd
3rd
D
6
7
A
A
A
A
A
A
A
A
Ea
Eb
Eb
Ea
Eb
Ea
Eb=04
Ea=04
Ea
Eb
Ea
Eb
Dowel
Drawer runner Caster and insert
β’
USE A HAMMER OR RUBBER MALLET TO
INSERT CASTER INSERT (PART Eb) INTO
THE BOTTOM OF THE FRONT CASTER
SUPPORT (PART 7) AND BACK CASTER
SUPPORT (PART 6).
β’
TAP ABOVE THE BACK OF THE CASTER
(ABOVE THE STEM) TO ASSEMBLE CASTERS
(PART Ea) INTO THE CASTER INSERT
(PART Eb).
TIP: Using a regular
hammer to attach the
runners provides a
clearer line of sight than
a rubber mallet.
Perform the entire assembly on a
clean, hard surface using the
flattened box or a towel to protect
the surface and the unit's finish. DO
NOT assemble on carpet.
Carpet creates too much bounce
making assembly difficult and could
lead to damage of the parts.
NOTICE: 7+(ξ:5,77(1ξ ,16758&7,216
CONTAINED +(5(,1ξ$5( &23<5,*+7('ξ
4-07
2
7
6
c
c
c
c
2
ATTACH CROSSBARS TO THE SIDE PANELS
ATTACH ONE SIDE FIRST AND THEN THE OTHER SIDE.
C
11
c
c
c
c
c
3
ATTACH THE TOP
CCCC
β’
LINE UP THE DOWEL HOLES IN TOP (PART 1)
WITH DOWELS THE IN UNITΒ΄S SIDES.
β’
SEE ROUND DIAGRAM:
SLIDE (PART C) SCREWS THROUGH ANGLED
POCKET HOLES.
AND HAND TIGHTEN FOR BEST FIT.
Screw 4,0 x 30mm
C= 4
Screw 4,0 x 30mm
C= 6
β’
β’
DO NOT STAND LEFT SIDE (PART 3) UP
ON THE EDGE YET. TO EASE ASSEMBLY,
LAY SIDE FLAT ON THE FLOOR, RUNNER
SIDE VISIBLE.
MATCH UP BACK CASTER SUPPORT
(PART 6) AND FRONT CASTER SUPPORT
(PART 7) AT DOWEL HOLES LOCATED AT
THE BOTTOM OF SIDE.
β’
PLEASE CHECK THAT THE DISTANCES
MATCH TO THE SQUARE DIAGRAM.
β’
SECURE BACK CASTER SUPPORT (PART 6) TO THE LEFT
SIDE (PART 3) USING SCREW (PART C).
SEE THE ROUND DIAGRAM, A BLOW UP IMAGE OF THE SCREW
POSITIONING TROUGH THE ANGLED POCKET HOLES.
β’
SECURE FRONT CASTER SUPPORT (PART 7) WITH SCREWS
(PART C) TO THE LEFT SIDE (PART 3) IN THE SAME MANNER.
β’
CAREFULLY TURN LEFT SIDE (PART 3) TO ITS BACK EDGE,
AS SHOWN IN THE DIAGRAM.
β’
POSITION RIGHT SIDE (PART 2) TO LINE UP THE CROSSBARS
(PART 6 AND 7) AT THE DOWEL HOLES AT BASE OF THE RIGHT
SIDE (PART 2).
β’
SECURE CASTER SUPPORTS (PART 6 AND 7) TO RIGHT SIDE
(PART 2) USING SCREW (PART C) AND SHOWN IN THE DIAGRAM.
TIP: HAND TIGHTEN FOR THE BEST FIT.
3
TIP: This
step is
easier with
two people.
TIP: Turning the
unit upside
down provides a
better angle to
tighten the
screws.
NOTICE: 7+(ξ:5,77(1ξ ,16758&7,216
CONTAINED +(5(,1ξ$5( &23<5,*+7('ξ
5-07
4
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
4
ATTACH THE BACK PANEL
β’
HOLD THE (PART 4) BACK PANEL IN THE
GROOVES INSIDE THE UNITΒ΄S SIDES.
β’
ALSO MAKE SURE THE BACK PANEL FITS IN THE
GROOVE AT THE BACK OF THE TOP.
β’
CHECK THAT THE UNIT IS SQUARE.
β’
SECURE THE (PART 4) BACK PANEL USING THE (PART F)
NAILS.
89
10
11
8
8
B
F
F
F=16
6X
5
ASSEMBLE THE DRAWERS
3,0 x 25mm
B=48
F=12
β’
LINE UP THE BOTTOM EDGE OF THE DRAWER
SIDE (PART 8) WITH THE BOTTOM EDGE OF THE
DRAWER FRONT (PART 11).
β’
JOIN THE PARTS USING TWO SCREWS (PART B)
AS SHOWN IN THE DIAGRAM.
NOTE: THE SCREWS' SHARP TIPS ARE SELF TAPPING, SO THE
DRAWER FRONT DOES NOT NEED A PILOT HOLE. THE SHARP
TIP STARTS THE HOLE, AND THE SCREW THREADS WILL
SECURE THE PART IN PLACE FOR A TIGHT FIT.
β’
REPEAT ON THE OTHER SIDE OF THE DRAWER.
β’
SLIDE IN DRAWER BOTTOM (PART 10) TROUGH GROOVES
IN THE DRAWER SIDES (PART 8). THIS WILL START
SQUARING UP THE DRAWER.
β’
LINE UP DRAWER BACK (PART 9) WITH BOTH DRAWER
SIDES (PART 8). CHECK THAT IT IS SQUARE.
β’
SCREW THE DRAWER BACK (PART 9) TO THE DRAWER
SIDES (PART 8).
β’
TURN THE DRAWER OVER. CONFIRM THE DRAWER BOTTOM
(PART 10) COVERS THE DRAWER BACK (PART 9). NAIL THE
DRAWER BOTTOM (PART 10) THROUGH TO THE DRAWER
BACK (PART 9) USING (2) NAILS (PART F).
Nail
Screw
Nail
TIP: To make this step easier, place the drawer upside
down on a counter with the drawer front hanging off
the edge. This will allow the drawer box to lay flat and
provide better control for hammering the nails.
Use all back
panels nails.
Evenly spaced,
they help make
the unit strong.
NOTICE: 7+(ξ:5,77(1ξ ,16758&7,216
CONTAINED +(5(,1ξ$5( &23<5,*+7('ξ
6-07
6
INSERT DRAWERS AND COMPLETE ASSEMBLY
β’
THE DRAWER SIDES (PART 8) HAVE A CHANNEL
THROUGH THE MIDDLE OF THE PART. THIS CHANNEL
SLIDES OVER THE DRAWER RUNNERS (PART D).
β’
SLIDE ALL DRAWERS IN.
AND CHECK THE DRAWERS RUN SMOOTH.
ONE DRAWER FRONT SHOULD NOT OVERLAP ANOTHER
DRAWER FRONT EDGE.
IF THERE IS A PROBLEM, IT IS LIKELY THE DRAWER FRONT IS NOT
ASSEMBLED LEVEL. SIMPLY BACK OUT ONE SET OF THE SCREWS
ON A DRAWER SIDE (PART 8) AND ADJUST UNTIL IT IS TO YOUR
SA TISFACTION.
(REMEMBER TO LINE THE BOTTOM EDGES OF THE DRAWER SIDE
(PART 8) AND DRAWER FRONT (PART 11) UP.)
β’
STEP BACK TO LOOK AT THE UNIT. YOU MAY PREFER TO
MOVE ONE DRAWER TO ANOTHERΒ΄S POSITION.
COMPLETED ASSEMBLY:
THANK YOU FOR YOUR PURCHASE, AND WELCOME TO ADEPTUS!
USE AND CARE INSTRUCTIONS:
CARE INSTRUCTIONS:
β’
NORMAL USE: WIPE WITH A CLEAN CLOTH.
β’
OR WHEN NEEDED TO CLEAN SCUFFS:WIPE CLEAN WITH A SLIGHTLY DAMP CLOTH AND A MILD CLEANER. THEN
WIPE DRY WITH A CLEAN CLOTH.
β’
IF YOU OIL OF WAX THIS FURNITURE, IT WILL MORE QUICKLY DEVELOP A PATINA AND DARKEN
USE:
MULTI-PURPOSE MOBILE STORAGE UNIT FOR HOME, OFFICE, CRAFT ROOM, KITCHEN, OR GARAGE.
NOTICE: 7+(ξ:5,77(1ξ ,16758&7,216
CONTAINED +(5(,1ξ$5( &23<5,*+7('ξ
7-07
/
