Extron Mounting Bracket Template

Brand: Extron

Model: Mounting Bracket

Type: Template

This manual is also suitable for

1-1Extron Mounting Bracket • Installation Guide

Extron Mounting Bracket Installation Guide

This guide gives an overview of how to install the following Extron mounting

brackets:

• 1-gang mounting bracket/mud ring,

part #70-163-01 (grey), #70-163-11 (black), #70-163-21 (white)

• MK mounting bracket/mud ring,

part #70-169-01 (black & white), 70-086-06 (grey), #70-086-16 (black),

#70-086-26 (white), #70-086-56 (unpainted)

• 2-gang mounting bracket/mud ring,

part #70-086-01 (grey), #70-086-11 (black), #70-086-21 (white)

• 3-gang mounting bracket/mud ring,

part #70-086-02 (grey), #70-086-12 (black), #70-086-22 (white)

• 4-gang mounting bracket/mud ring,

part #70-086-03 (grey), #70-086-13 (black), #70-086-23 (white)

• 5-gang mounting bracket/mud ring,

part #70-086-04 (grey), #70-086-14 (black), #70-086-24 (white)

• 10 x 8 mounting bracket/mud ring,

part #70-164-01 (grey), #70-164-11 (black), #70-164-21 (white)

Determine the Installation Location

The mounting brackets do not require attachment to wall studs, so they can be

placed almost anywhere on a wall. When you determine where to install the

device and mounting bracket, consider cable placement and access. You may need

to install the cables before installing the bracket.

Prepare the Installation Site

1. Photocopy the appropriate full size rough-in template from one of the

following pages. Cut out the center portion of the template up to the dashed

guidelines.

2. Place the template copy in the desired orientation and location on the

installation surface (wall). Use a soft pencil to mark the guidelines for the

opening on the installation surface.

3. Use a jigsaw or small hand saw to carefully cut away the material within the

guidelines.

4. Check the opening size by laying the mounting bracket against the opening.

The flat portion should lay snugly on the wall, and the tabs through which the

screws will be inserted should fit easily into the opening. There should not be

noticeable play within the opening.

5. If needed, use a saw, file or sandpaper to enlarge the hole. Smooth the edges

of the opening to avoid damage or injury to yourself or the cables during

installation.

Install the Mounting Bracket

Fastening the bracket with backing clips

Use this installation method if the installation surface is wallboard, particle board,

or soft wood.

68-426-01 E

Printed in the USA

09 01

Installation Guide, cont’d

Extron Mounting Bracket • Installation Guide1-2

1. Place 1¼” (3.18 cm) long or ¾“ (1.90 cm), #6-32 thread machine screws

(provided) through the holes in each corner of the mounting bracket. Use the

shortest possible screw needed.

Loosely fasten (using 2-3 turns) a mounting backing clip on the end of each

screw.

2. Insert the mounting bracket into the opening in the wall.

3. Rotate each clip so the tab will be behind the plywood, wallboard/sheet rock

or other surface to hold the bracket snugly in place when the screw is

tightened. See Detail A and Detail B.

Detail A

0.75" #6-32 Screw

Backing Clip

Wall Material

Mounting Bracket

Detail B

1.25" #6-32 Screw

4. Use a Phillips screwdriver to hand tighten the screws to fasten the mounting

bracket in place.

Mounting Bracket

Backing clip can

be in either orientation.

See Detail A or Detail B.

Backing clip can

be in either orientation.

See Detail A or Detail B.

Fastening the bracket with wood or sheet metal screws

Use this installation method if the installation surface is a sturdy, dense material

such as sheet metal, plywood, or hard wood.

1. Insert the mounting bracket into the opening in the wall and hold it firmly in

place.

2. Mark the locations of the outermost/corner bracket holes on the installation

surface.

3. If desired, remove the mounting bracket and drill ¼” deep pilot holes (half the

width of the shaft of the screw) at the marked locations.

4. Insert the bracket back into the hole.

5. Use four ½” (1.3 cm) long, #6 flat headed wood screws (provided) or self-

tapping sheet metal screws to fasten the bracket directly onto wood or metal,

respectively. Hand tighten the screws. See the illustration below.

Mounting Bracket

1-3Extron Mounting Bracket • Installation Guide

The dashed line indicates the

recommended cut-out area

(3.76” H x 2.20” W)

for the installation surface.

The solid, outer line

(4.50” H x 2.79” W)

represents the outside edge

of the wall mounting bracket.

Template for the 1-gang

mounting bracket

The dashed line indicates the

recommended cut-out area

(2.68” H x 4.94” W)

for the installation surface.

The solid, outer line

(3.38” H x 5.70” W)

represents the outside edge

of the wall mounting bracket.

Template for the

MK mounting bracket

Installation Guide, cont’d

Extron Mounting Bracket • Installation Guide1-4

The dashed line indicates the recommended

cut-out area (3.875” H x 3.80” W)

for the installation surface.

The solid, outer line (4.50” H x 4.60” W)

represents the outside edge

of the wall mounting bracket.

Template for the 2-gang

mounting bracket

The dashed line indicates the recommended

cut-out area (3.875” H x 5.613” W)

for the installation surface.

The solid, outer line (4.50” H x6.413” W)

represents the outside edge

of the wall mounting bracket.

Template for the 3-gang

mounting bracket

1-5Extron Mounting Bracket • Installation Guide

The dashed line indicates the recommended

cut-out area (3.875” H x 7.525” W)

for the installation surface.

The solid, outer line (4.50” H x8.325” W)

represents the outside edge

of the wall mounting bracket.

Template for the 4-gang

mounting bracket

Installation Guide, cont’d

Extron Mounting Bracket • Installation Guide1-6

The dashed line indicates the

recommended cut-out area

(3.88” H x 9.31” W)

for the installation surface.

The solid, outer line

(4.50” H x 10.14” W)

represents the outside edge

of the wall mounting bracket.

Template for the 5-gang

mounting bracket (mud ring)

1-7Extron Mounting Bracket • Installation Guide

The dashed line indicates the recommended

cut-out area (7.53” H x 9.52” W)

for the installation surface.

The solid, outer line (8.25” H x 10.25” W)

represents the outside edge

of the wall mounting bracket.

Template for the 8 x 10 (8.25" x 10.25")

mounting bracket

Installation Guide, cont’d

Extron Mounting Bracket • Installation Guide1-8

This page is left blank intentionally.

Extron Mounting Bracket Template

Brand: Extron

Model: Mounting Bracket

Type: Template

This manual is also suitable for

Download PDF

report

Extron Mounting Bracket Template

This manual is also suitable for

Extron Mounting Bracket Template

Related papers

Other documents