KERN TYKUP-13-A Installation guide

  • Hello! I have analyzed the KERN KUP-13 Assembly Instructions. This document provides guidance for installing the interface adapter, which allows you to connect up to three interfaces to a KERN extension box. I'm ready to answer your questions about the KUP-13 adapter and its functionalities.
  • How many interfaces can be connected using the KERN Extension Box?
    Can the connected interfaces be used simultaneously?
    What type of adapters can be connected to the 15-pin sub-D connector of the balance?
    Is the interface adapter automatically recognized by the device?
KERN & Sohn GmbH
Ziegelei 1
D-72336 Balingen
Tel: +49-[0]7433- 9933-0
Fax: +49-[0]7433-9933-149
Internet: www.kern-sohn.com
Installationsanleitung
Assembly instructions
Istructions d’installation
KERN KUP-13
TYKUP-13-A
Version 1.1
2023-06
TYKUP-13-A-IA-def-2311
TYKUP-13-A-IA-def-2311 1
Deutsch
D
Schnittstellenadapter mit Kabel für Extension
Box
Version 1.1 2023-06
Installationsanleitung
Inhaltsverzeichnis
1 Lieferumfang............................................................................................... 1
2 Allgemeines ................................................................................................ 1
3 Installation .................................................................................................. 1
1 Lieferumfang
Schnittstellenadapter mit Kabel für Extension Box
Installationsanleitung
2 Allgemeines
Kabellänge: 0,15 m
Über die KERN Extension Box können bis zu 3 beliebige Schnittstel-
len angeschlossen werden. Diese lassen sich jedoch nur einzeln ver-
wenden und nicht gleichzeitig.
Kaskadieren ist nicht möglich!
Es dürfen nur KERN KUP-Adapter an den 15-pol-Sub-D-An-
schluss der Waage angeschlossen werden!
3 Installation
1. Gerät ausschalten.
2. Schnittstellenadapter in den KUP-Anschluss des Gerätes einstecken.
3. Gerät einschalten. Der Schnittstellenadapter wird automatisch vom Gerät er-
kannt. Es kann allerdings bis zu einer Minute dauern, bis die Schnittstellen ver-
wendet werden können.
TYKUP-13-A-IA-def-2311 1
English
GB
Interface Adapter with Cable for Extension Box
Version 1.1 2023-06
Installation Instructions
Contents
1 Scope of delivery ........................................................................................ 1
2 General information ................................................................................... 1
3 Installation .................................................................................................. 1
1 Scope of delivery
Interface Adapter with Cable for Extension Box
Installation Instructions
2 General information
Cable length: 0,15 m
Via the KERN Extension Box up to 3 interfaces of your choice can be
connected. However, these can only be used on their own and not at
the same time.
Cascading is not possible!
Only KERN KUP adapters may be connected to the 15-pol-sub-D-
plug of the device!
3 Installation
1. Switch off the appliance
2. Plug in the interface adapter at the KUP connection
3. Switch on the appliance. The interface adapter is automatically recognized by the
appliance. However, it may take up to one minute before the interfaces can be
used.
TYKUP-13-A-IA-def-2311 1
Français
F
Adaptateur d'interface avec câble pour Exten-
sion Box
Version 1.1 2023-06
Notice d'installation
Table des matières
1 Etendue de la livraison .............................................................................. 1
2 Général ........................................................................................................ 1
3 Installation .................................................................................................. 1
1 Etendue de la livraison
Adaptateur d'interface avec câble pour Extension Box
Notice d'installation
2 Général
Longueur de câble: 0,15 m
La KERN Extension Box permet de connecter jusqu'à 3 interfaces au
choix. Celles-ci ne peuvent toutefois être utilisées qu'individuellement
et pas simultanément.
La mise en cascade n'est pas possible!
Seuls les adaptateurs KERN KUP peuvent être raccordés au
connecteur Sub-D à 15 broches de la balance!
3 Installation
1. Eteindre l’appareil.
2. Insérer l'adaptateur d'interface dans le connecteur KUP de l'appareil.
3. Allumer l'appareil. L'adaptateur d'interface est automatiquement reconnu par
l'appareil. Il peut toutefois s'écouler jusqu'à une minute avant que les interfaces
ne puissent être utilisées.
/