Alpha HDN 300/600 Installation guide

Alpha
Brand
Alpha
Model
HDN 300/600
Type
Installation guide
HIGH DENSITY NETWORKED DC DISTRIBUTION
HDN
INSTALLATION AND OPERATION MANUAL
Comm/net Systems, Inc.
4237 – 24th Avenue West
Seattle, WA 98199
TEL: 206.282.8670
FAX: 206.282.8684
www.commnetsystems.com
24/7 Sales & Service
To purchase Comm/net Systems solutions, contact your
Comm/net Systems representative at: (800) 274-0544
or e-mail: [email protected]
For product support, email: [email protected]
About Comm/net Systems
Comm/net Systems, Inc. (CSI) is the leader in high power density communications power systems. Comm/net oers comprehensive
power and communications site systems integration and deployment services via a national footprint of regional branch oces.
Additional information can be found at www.commnetsystems.com.
© 2018 Comm/net Systems. All rights reserved. Comm/net Systems, and the Comm/net Systems logo are registered trademarks
of Comm/net Systems, Inc. in the United States and other countries. All other trademarks, service marks, registered marks, or
registered service marks are the property of their respective owners. Comm/net Systems assumes no responsibility for any
inaccuracies in this document. Comm/net Systems reserves the right to change, modify, transfer, or otherwise revise this
publication without notice.
Document Number: 048-692-30
Revision Level: r08
Published: July 2018
INSTALLATION AND OPERATION MANUAL
HIGH DENSITY NETWORKED DC DISTRIBUTION
HDN
InstallatIon and operatIon Manual
Table of Contents
Section 1: Purpose and Applicability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Product Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Firmware Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Section 2: Product Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Section 3: Theory of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
3.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
3.2 Conguration Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Section 4: Unpacking and Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
4.1 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Section 5: Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
5.1 Selecting an Installation Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
5.2 Mechanical Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
5.3 Chassis Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
5.4 Input Power Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
5.5 Alarm Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
5.6 Output Power Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
5.7 Installing Circuit Breakers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5.8 Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Section 6: Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6.1 How to Review System Status via Display LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6.1.1 Power Input A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6.1.2 Power Input B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
6.1.3 Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Section 7: System Status Review via Supervisory Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
7.1 Home Screen Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
7.1.1 Home Screens - Single Input Models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
7.1.2 Home Screens - Dual Input Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
7.2 Initial Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
7.2.1 Breaker Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
7.2.2 Set Breaker Ampacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
7.2.3 Warning and Alarm Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
7.2.4 Set Date/Time and Data Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
7.3 Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
7.3.1 Alarm/Warnings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
7.3.2 History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
7.3.3 Breaker Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
7.4 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
7.4.1 System Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
7.4.2 Breaker Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
7.4.3 Calibration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
InstallatIon and operatIon Manual
7.4.4 Advanced Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7.5 Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7.5.1 Normal Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7.5.2 Warning Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Breaker Overload | A1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
A-B Redundant Warn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
A1-B1 Redundant Warn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Current Sensor Fail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
7.5.3 Alarm Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Breaker Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Non-Inventoried Breaker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Bus Overcurrent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
High Input Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Low Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
7.6 How to Review System Status via the Embedded Webserver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7.6.1 Default Static Network Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7.7 Navigating the Webserver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Section 8: Product Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
8.1 Physical Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
8.2 Electrical Specications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
8.2.1 Single Input Models 016-991-10 & 016-996-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
8.2.2 A/B Isolated Input Model 016-992-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Appendix A: The Rack Mount Power Termination Panel (PTP-RM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
A.1 PTP Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
A.2 PTP Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Appendix B: Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
PAGE 1
HDN HIGH DENSITY NETWORK DC DISTRIBUTION
InstallatIon and operatIon Manual: purpose and applIcabIlIty
Section 1: Purpose and Applicability
The purpose of this document is to detail the installation and operation instructions for the HDN High Density DC Distribution
Center.
1.1 Product Model
This document applies to Comm/net Systems, Inc products in the following model congurations:
016-991-10 HDN Single Input
016-992-10 HDN A/B Isolated Input, Split Bus Output
016-996-10 HDN Single Input (BDFB Model)
016-994-10 PTP, PTP-RM, 2RU Top Bus Power Termination Panel (accessory)
1.2 Firmware Version
This document applies to the following product rmware version(s):
034-033-34 HDN Supervisory Controller r01 and newer
For legacy rmware support, contact Comm/net Systems.
Section 2: Product Support
If you have any questions concerning Comm/net Systems products and services, contact our support sta. Our knowledgeable
support team can provide product technical support, or answer other questions regarding Comm/net products and services.
In addition to contacting Comm/net Support directly via phone or e-mail, our online help desk is available 24 hours a day, 7 days
a week. The help desk includes commonly asked questions and self-help articles as well as an online ticket submission system if
you need to contact Comm/net after normal business hours.
Comm/net support is available by phone or e-mail Monday – Friday from 8am – 4:30pm Pacic time.
The online web portal is available 24/7 to submit support requests and general questions or view the FAQ and self-help articles.
All questions submitted to the web portal will be answered during normal business hours.
Phone: 1-800-274-0544
E-mail: support@commnetsystems.freshdesk.com
Online Web Portal: www.commnetsystems.freshdesk.com
PAGE 2
HDN HIGH DENSITY NETWORK DC DISTRIBUTION
InstallatIon and operatIon Manual: theory of operatIon
Section 3: Theory of Operation
The HDN is an advanced, high-density DC distribution center for rack-mount telecom and broadband applications. Its robust
design distributes power for up to 22 loads. The advanced supervisory control allows local and remote monitoring of not only
breaker status, but of individual load current, and input bus current.
3.1 Features
High-Reliability, High-Density Breaker Distribution
Dual Isolated Power Inputs or Single Input versions
600A Maximum Total Load
22 AM Breaker Positions
100A Max per Breaker Position
Intuitive Touchscreen Interface
RGB Backlight and Bright LEDs Indicate Status at a Glance
Current Monitoring Per Output
Form C Alarm Contacts
Optional Ethernet Module with Integrated Web Interface and SNMP Support (V.1 and V.2)
3.2 Conguration Options
Adjustable brackets for 19" or 23" rack mount installation
Section 4: Unpacking and Inspection
The Comm/net HDN was carefully packaged at the factory to withstand the normal rigors of shipping. However, you should
carefully inspect the box and contents to conrm that no damage occurred in transit. Most shipping carriers require notication
of shipping damage within twenty-four hours of delivery, and it is the responsibility of the recipient to inspect the shipment
immediately upon receipt.
PAGE 3
HDN HIGH DENSITY NETWORK DC DISTRIBUTION
InstallatIon and operatIon Manual: InstallatIon
4.1 Package Contents
Included with your product are the following items:
HDN Distribution Panel
Mounting hardware kit with necessary bolts and washers
Rear plastic bus bar safety shield
Section 5: Installation
5.1 Selecting an Installation Location
The HDN panel can be installed in any standard 19-inch or 23-inch relay rack. The
panel itself occupies only 3RU, but it is recommended that space be left free above
and below the panel to ease cable routing. It is common to mount the HDN panel at
the topmost rack position.
IMPORTANT: If the PTP option is to be included, a total of 5RU + cable routing space
is required for installation. For more information, see See "Appendix A: The Rack
Mount Power Termination Panel (PTP-RM)" on page 12.
5.2 Mechanical Mounting
WARNING
BEFORE BEGINNING THE INSTALLATION PROCESS, MAKE SURE ALL INPUT FEED BREAKERS ARE TURNED OFF FOR SAFETY
DURING THE INSTALLATION PROCESS AND TO PROTECT THE EQUIPMENT FROM DAMAGE.
THE INSTALLATION OF THIS PANEL SHOULD ONLY BE PERFORMED BY QUALIFIED PERSONNEL WITH PROPER TOOLS AND
PROTECTIVE SAFETY EQUIPMENT. PROTECTIVE EYE WEAR AND INSULATED TOOLS ARE RECOMMENDED.
The HDN can be mounted in a front ush mount conguration or a mid-mount conguration. Depending on the desired
conguration, attach the mounting ears accordingly.
Step 1. Orient the rack mount ears appropriately for a 19 or 23 inch rack.
Step 2. For ush mounting, install the rack mount ears using the included Phillips head screws through the two holes near the
front of the panel. For mid-mount conguration, use the two holes further back on the sides of the panel.
Step 3. Insert the panel into the rack and attach with included 12-24 rack screws.
Figure 1. HDN Panel
Figure 2. HDN Panel with Rear Plastic Shield
PAGE 4
HDN HIGH DENSITY NETWORK DC DISTRIBUTION
InstallatIon and operatIon Manual: InstallatIon
5.3 Chassis Ground
The chassis ground cable should be landed on the two threaded holes marked "Chassis
Ground" on the left side of the panel. See "Figure 3. Chassis Ground" on page 4.
A minimum of a #6 AWG cable is required. The holes are 1/4-20 on 5/8" centers.
Recommended Grade 5 Torque Value: 100 in·lbs
5.4 Input Power Connection
WARNING
USE ONLY THE 3/8"16 X 1" BOLTS, SPLIT WASHERS AND FLAT WASHERS PROVIDED. USE OF ANY OTHER HARDWARE MAY
DAMAGE THE PANEL.
Step 1. Install a piece of clear heatshrink tubing (3" diameter x 6" long) over each of the power cables prior to bolting the cable
lugs to the bus bars.
Step 2. Connect the incoming DC feeder cables for the A and B power inputs and A and B power returns for the A/B isolated
panel. For a single input panel there will be one power input and one return bus bar. See "Figure 15. HDN A/B Isolated
Input Connection Detail" on page 14.
Step 3. Secure the cable lugs to the bus bars with the included 3/8"x1" bolts, at washers and lock washers. The bus bars
support lugs with 1" hole spacing. Recommended Grade 5 Torque Value: 350 in·lbs
5.5 Alarm Wiring
The HDN features two 8p8c modular jacks (RJ-45) for alarm connections on the rear of the panel. The alarm contact pinout is
below:
ALARM CONTACT PINOUT
PIN 1 PIN 2 PIN 3 PIN 48
COM NC NO Reserved
The two jacks allow for easy daisy-chaining with UTP patch cables. If daisy-chaining, the NO (normally open) condition must be
monitored.
5.6 Output Power Connection
Land the return cable lug to its corresponding position on the return bus bar, then land the hot cable lug to the corresponding
position below. The studs are 1/4"-20 on 5/8" centers. Recommended Grade 5 Torque Value: 100 in·lbs
Once all cables are landed and secured, install the rear plastic safety cover using the black 8-32 panhead screws provided.
Figure 3. Chassis Ground
PAGE 5
HDN HIGH DENSITY NETWORK DC DISTRIBUTION
InstallatIon and operatIon Manual: operatIon
5.7 Installing Circuit Breakers
Step 1. Turn the captive mounting screws counterclockwise and lift the front panel.
Step 2. Slide a circuit breaker of sucient ampacity into the position corresponding to the output channel to be fed.
NOTE: When viewing from the front of the panel, from left to right, the lower channel positions begin on the left and are counted
upwards as you move right.
WARNING
ENSURE THAT CIRCUIT BREAKERS ARE ORIENTED SUCH THAT THE "ON" POSITION IS AT THE TOP.
Step 3. Push all installed circuit breakers rmly to ensure the terminals are fully seated in their sockets.
5.8 Installation Checklist
Rack mount ears mounted securely to the panel and the rack?
Chassis ground cable connected?
Input power cables (A Hot, A Return, B Hot, B Return) securely bolted to the correct bus bars and heat shrink installed?
Alarm cable connected and wired correctly to remote monitoring device (if required)?
Output feed cables landed to correct polarity?
Wire lacing or cable ties installed to provide strain relief?
Breakers installed in the correct positions and fully seated?
Rear safety cover installed?
Section 6: Operation
6.1 How to Review System Status via Display LEDs
The HDN features bright front panel LEDs that allow for the overall panel status to be determined at a glance.
6.1.1 Power Input A
This LED will illuminate BLUE when power is present on the A input.
PAGE 6
HDN HIGH DENSITY NETWORK DC DISTRIBUTION
InstallatIon and operatIon Manual: systeM status revIew vIa supervIsory controller
6.1.2 Power Input B
This LED will illuminate BLUE when power is present on the B input.
6.1.3 Alarm
This LED will illuminate RED if a breaker has tripped or if any other alarm condition exists. Under normal conditions this light is not
illuminated.
Section 7: System Status Review via Supervisory Controller
The HDN panel uses a touchscreen user interface. Interact with the touchscreen by using your ngertip, a stylus, or a capped pen
to touch the display and select status information, or to access the menu. In addition to the status LEDs, the backlight of the LCD
will change color based on the status of the panel. See "7.5 Operating Conditions" on page 9.
7.1 Home Screen Information
The home screen displays input bus voltage, input bus current, inventoried breakers,
and alarm conditions. There are multiple home screens depending on which HDN
model is installed (see below)
Touch any item on the home screen to access their submenus and displays.
Touch the main display area to cycle between home screens.
7.1.1 Home Screens - Single Input Models
1. Input Voltage & Bus Load with a bar graph displaying total load. See "Figure 4.
Home Screen - HDN Single Input" on page 6.
2. Bar graphs showing the total load of all 22 breaker channels. Breakers which are
inventoried will be shaded on the bottom of the display. See "Figure 5. Bar Graph
Home Screen - HDN Single Input" on page 6.
7.1.2 Home Screens - Dual Input Models
1. Input Voltage & Bus Load for A & B inputs.
2. Bar graph of the A & B total load.
3. Bar graphs showing the total load of all 22 breaker channels. Breakers which are
inventoried will be shaded on the bottom of the display.
Figure 4. Home Screen - HDN Single Input
Figure 5. Bar Graph Home Screen - HDN
Single Input
PAGE 7
HDN HIGH DENSITY NETWORK DC DISTRIBUTION
InstallatIon and operatIon Manual: systeM status revIew vIa supervIsory controller
7.2 Initial Operation
7.2.1 Breaker Inventory
IMPORTANT: Make sure that all breakers to be inventoried are turned "ON".
Step 1. From the Home Screen, go to the Breakers menu (Settings > Breakers).
Step 2. Select "Take Inventory". All installed and active breakers will be displayed.
Follow the on-screen prompts to complete the inventory process. See "Figure
6. Breaker Inventory" on page 7.
7.2.2 Set Breaker Ampacity
From the Breaker menu (Settings > Breakers), set the breaker ampacity by tapping on
any of the three number boxes to change the number. The default set ampacity is
100A, which is also the maximum ampacity for an installed single-pole breaker. See
"Figure 7. Setting Breaker Ampacity" on page 7.
2-pole breakers can be adjusted to a maximum of 200A, and 3-pole breakers support a
maximum of 300A. To toggle the number of breaker poles, tap the numbered breaker
position on the screen. The display will change to indicate the set number of poles,
and which positions are occupied. See "Figure 8. Setting a Multi-Pole Breaker" on page
7, which displays circuits B03-05 managed by a 3-pole breaker.
NOTE: The position of a multi-pole breaker will be the furthest left position occupied
(for example, if a breaker occupies A02-04, the breaker will be identied as Breaker A02).
7.2. 3 Warning and Alarm Threshold
From the Breaker menu (Settings > Breakers), set the alarm threshold to any value
between 40% and 100%. This is the amount of breaker utilization which will trigger an
overcurrent alarm. A local warning will be sent at 10% less than the set alarm threshold.
The default is 80%. See "Figure 9. Breaker Settings Menu" on page 7.
NOTE: This threshold is congured by default to monitor as a redundant panel. It sums
the current between the corresponding A and B side outputs.
7.2.4 Set Date/Time and Data Log
Access the Data Log menu (Settings > Advanced > Data Log) and select "Date/Time".
You can also set the rate in which data is collected on the SD card. The default rate is
every 15 minutes. To change the collection rate, go to the Data Log and select "Set
Rate".
Figure 6. Breaker Inventory
Figure 7. Setting Breaker Ampacity
Figure 8. Setting a Multi-Pole Breaker
Figure 9. Breaker Settings Menu
PAGE 8
HDN HIGH DENSITY NETWORK DC DISTRIBUTION
InstallatIon and operatIon Manual: systeM status revIew vIa supervIsory controller
NOTE: If these actions are not performed, data will not be stored on the SD card.
7.3 Main Menu
7.3.1 Alarm/Warnings Menu
The color of the screen indicates the condition of the panel at a glance. A red screen
indicates a critical alarm is present, and orange indicates a warning condition. An
alarm icon will be present for both alarm and warning conditions. Press this icon to
access the alarm logs, review logs, and to silence the audible alarm locally. See "Figure
10. Alarm Condition" on page 8.
7.3. 2 History
From the History menu, data on voltage and current for busses and individual channels
can be accessed. See "Figure 11. History" on page 8.
7.3.3 Breaker Detail
Shows detailed information about each channel. Cycle through the breakers by
touching the left and right arrows on the screen. See "Figure 12. Breaker Detail" on
page 8.
7.4 Settings
7.4.1 System Settings
The following settings are congured in Systems Settings:
Redundant Monitor (Yes or No, Default Yes)
Firmware Number Display (on second page)
Default Home Screen
Preferred Bar Graph units (Percent Full Load, or Load in Amps)
7.4.2 Breaker Settings
Take Inventory
Set Breakers (Set channel ampacity, default is 100A)
% Alarm Threshold (Warning threshold is -10% from alarm threshold. Default alarm threshold is 80%)
Figure 10. Alarm Condition
Figure 11. History
Figure 12. Breaker Detail
PAGE 9
HDN HIGH DENSITY NETWORK DC DISTRIBUTION
InstallatIon and operatIon Manual: systeM status revIew vIa supervIsory controller
7.4.3 Calibration Settings
IMPORTANT: DO NOT adjust any Calibration Settings without direct instruction from Comm/net Systems.
7.4.4 Advanced Settings
Memory
• Settings - Clear settings to factory default. IMPORTANT: Do not perform this function without direction from
Comm/net Personnel!
• Calibration - Clears calibration. IMPORTANT: Do not perform this function without direction from Comm/net
Personnel!
• EEPROM - This clears the EEPROM. IMPORTANT: Do not perform this function without direction from Comm/net
Personnel!
• SD Card - This clears the memory from the on-board SD card.
Display - Allows calibration of display settings such as contrast and touch calibration.
Test Modes - Contains various test settings such as breaker trip and alarm testing which can be useful during installation or
for troubleshooting.
Data Log
• Set Date and Time (NOTE: If Date/Time is not set, data will not be recorded to the SD card)
• Set Data Sample Rate (Default is every 15 min)
7.5 Operating Conditions
The HDN Supervisory Controller features colored backlit displays, graphic icons and audible alarms to indicate its current
operating condition(s).
7.5.1 Normal Condition
A blue screen indicates normal operating conditions.
7.5. 2 Warning Condition
A warning condition will only be visible locally and will not cause an alarm contact
closure or trigger an SNMP trap. It is denoted on the Supervisory Controller display
by an orange screen and the presence of the Alarm/Warning symbol in the upper left
hand corner of the home screen. See "Figure 13. Warning Condition" on page 9
Please note that the bus and channel names given below may dier depending on the
bus(ses) and/or channel(s) being aected.
NOTE: For multi-pole breakers, the warning condition will show for the primary
position (Example: If a two-pole breaker in positions A02-A03 is in warning, then a
warning alarm will show for position A02)
Breaker Overload | A1
Figure 13. Warning Condition
PAGE 10
HDN HIGH DENSITY NETWORK DC DISTRIBUTION
InstallatIon and operatIon Manual: systeM status revIew vIa supervIsory controller
This warning will occur when a chanel is 10% below the set channel over-current threshold. This threshold is congured in the
breaker settings menu. See "7.4.2 Breaker Settings" on page 8.
A-B Redundant Warn
This warning indicates that the summed load of busses A and B and are approaching the over-current threshold for one bus. This
warning occurs at 10% below the bus over-current threshold.
NOTE: This alarm only occurs when the redundant monitoring feature is enabled. Redundant monitoring is enabled by default.
See "7.4.1 System Settings" on page 8.
A1-B1 Redundant Warn
This warning indicates that the summed load of two redundant channels has reached over-current threshold. Redundant
channels are channels with the same number value, such as A1 and B1 in a dual input panel, or corresponding channels in paired
single input panels.
This threshold can be congured in the breaker setting menu. See "7.4.1 System Settings" on page 8.
Current Sensor Fail
This warning indicates there is an issue with an internal sensor or its circuitry. Try to reset the controller using the reset switch on
the left-hand side of the controller. If the warning persists, contact Comm/net support for more information and diagnostic steps.
IMPORTANT: Resetting the controller will reset the clock. If you do this, be sure to set the date/time again. See "7.4.4 Advanced
Settings" on page 9 for information on setting the date/time.
7.5. 3 Alarm Conditions
A red screen indicates that one of the following alarm conditions are present. These are critical alarm conditions that will
annunciate locally as well as trigger alarm contact closures and trigger SNMP traps.
Breaker Trip
Occurs if any inventoried breaker trips for any reason.
NOTE: For multi-pole breakers, a breaker trip alarm will show for all occupied positions (Example: If a two-pole breaker in positions
A02-A03 is in breaker trip alarm, then an alarm will show for positions A02 and A03)
Non-Inventoried Breaker
Occurs if a breaker is turned on and is not inventoried. To x this, perform a breaker inventory to add all active channels to
inventory. See "7.2.1 Breaker Inventory" on page 7.
Bus Overcurrent
Occurs when a bus exceeds its current alarm threshold. The threshold is set to 80% by default.
High Input Voltage
Alarm is triggered when input voltage exceeds 56V.
Low Input voltage
PAGE 11
HDN HIGH DENSITY NETWORK DC DISTRIBUTION
InstallatIon and operatIon Manual: product specIfIcatIons
Alarm is triggered when input voltage drops below 47V.
7.6 How to Review System Status via the Embedded Webserver
The optional embedded ethernet module provides remote monitoring via IP-based ethernet networks and a web browser. To
view the system status, you will need to connect the ethernet port on the rear of your HDN to your network.
By default, the ethernet module is congured at the factory with a static IP address and network settings, dened below. Use
these settings to set up a local network to communicate with the embedded webserver. Enter the static IP address into a web
browser:
192.168.123.123
Once you establish a connection to the embedded ethernet module, use the following credentials to gain access to the protected
data and administrative pages:
Username: root
Password: password
7.6.1 Default Static Network Settings
Use these settings to set up a local network to communicate with the embedded webserver. Enter the static IP address into a web
browser.
IPV4 Address: 192.168.123.123
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.123.1
Default DNS: 192.168.123.1
Secondary DNS: 8.8.8.8
7.7 Navigating the Webserver
Once you access the webserver you will be able to review the status of the HDN panel.
You can also access and change notication, network, and other settings via the Administration Settings tab.
Section 8: Product Specications
8.1 Physical Specications
The product has the following mechanical specications:
PAGE 12
HDN HIGH DENSITY NETWORK DC DISTRIBUTION
InstallatIon and operatIon Manual: product specIfIcatIons
Dimensions: 17" wide x 5.2" high (3RU) x 12.5" deep (including bus bar protrusion)
Weight: 27lbs (without breakers)
8.2 Electrical Specications
The electrical specications vary between models. Make sure you identify the correct model and electrical ratings before
servicing or adding additional load to the panel.
8.2.1 Single Input Models 016-991-10 & 016-996-10
Input voltage: -40V to -60VDC
Single input bus
22 circuit breaker channels (1 through 22)
600A maximum total load
100A max per breaker channel
Form C alarm contacts
8.2.2 A/B Isolated Input Model 016-992-10
Input voltage: -40V to -60VDC
A/B isolated inputs with split bus output
22 circuit breaker channels (11A /11B)
600A maximum per input
600A maximum total load
100A max per breaker channel
Form C alarm contacts
Appendix A: The Rack Mount Power Termination Panel (PTP-RM)
The Rack Mount Power Termination Panel (PTP-RM) allows large gauge
feeder cables (500kcmil and 750kcmil) to supply an HDN distribution panel.
NOTE: The PTP is only compatible with an HDN panel that is ush mounted.
Mid-mounted HDN panels cannot be fed by a PTP-RM.
A.1 PTP Installation Procedure
WARNING
BEFORE BEGINNING THE INSTALLATION PROCESS, MAKE SURE ALL INPUT FEED BREAKERS ARE TURNED OFF FOR SAFETY
DURING THE INSTALLATION PROCESS AND TO PROTECT THE EQUIPMENT FROM DAMAGE.
Figure 14. Rear View of HDN Panel with PTP Option
PAGE 13
HDN HIGH DENSITY NETWORK DC DISTRIBUTION
InstallatIon and operatIon Manual: product specIfIcatIons
THE INSTALLATION OF THIS PANEL SHOULD ONLY BE PERFORMED BY QUALIFIED PERSONNEL WITH PROPER TOOLS AND
PROTECTIVE SAFETY EQUIPMENT. PROTECTIVE EYE WEAR AND INSULATED TOOLS ARE RECOMMENDED.
Step 1. Before installing the HDN, attach the four connecting bus bars supplied with the PTP to the power inputs of the HDN
using the provided 3/8"x1" bolts, at washers and lock washers. The two HOT bus bars (the larger two of the four bus bars)
require four bolts each. The two RETURN bars (the smaller bus bars) each require two bolts. Recommended Grade 5
Torque Value: 350 in·lbs
WARNING
USE ONLY THE PROVIDED 3/8"16 X 1" BOLTS, SPLIT WASHERS, AND FLAT WASHERS. USE OF OTHER HARDWARE MAY DAMAGE
THE PANEL.
Step 2. Install the HDN in the rack rst, but do not connect any cables to it. When installing the HDN, be sure to leave at least
2RU of free rack space above the panel for the PTP.
Step 3. Orient the PTP rack mount ears appropriately for a 19 or 23 inch rack. Install the rack mount ears using the included
Phillips Head screws through the two holes near the front of the panel.
Step 4. Install the PTP in the rack. Be sure the four input bus bars attached to the back of the HDN are aligned with the bus bars
of the PTP.
Step 5. Secure the connecting bus bars on the HDN to the PTP using the 3/8-16x1" bolts provided. Each connecting bus bar
requires two bolts. In the two hole positions, the bolt also retains the mounting bracket for the rear cover. See "Figure
17. PTP Power Termination Panel connected to the HDN bus bars" on page 16. Recommended Grade 5 Torque Value:
350 in·lbs
Step 6. Install a piece of clear heatshrink tubing over each of the power cables prior to connecting the cable lugs to the PTP bus
bars.
Step 7. Install the incoming DC feeder cables for the A and B power inputs and A and B returns. The cables can feed in from the
rear of the PTP or feed down from the top. The bus bars of the PTP support lugs with 1" hole spacing.
Step 8. Secure the cable lugs to the bus bars using the provided 3/8" x 1 1/4" and 3/8" x 1 1/2" bolts, at washers and lock
washers. Recommended Grade 5 Torque Value: 350 in·lbs
Step 9. Knock out the sections of the plastic cover that match your input feeder landings (either rear-entry or top-entry), then
install the plastic cover using the 1/4-20 serrated head screws provided. See "Figure 18. Secure the plastic safety shield to
the PTP Power Termination Panel" on page 16.
A.2 PTP Installation Checklist
Rack mount ears mounted securely to the panel and the rack?
Are the four connecting bus bars (A Hot, A Return, B Hot and B Return) securely fastened to their corresponding inputs on the
HDN (12 bolts total)?
Are there four connecting bus bars securely fastened to their corresponding bus bars on the PTP (8 bolts total)?
Heat shrink installed over input power cable lugs?
Input power cables (A Hot, A Return, B Hot and B Return) securely bolted to the correct PTP bus bars?
Wire lacing or cable ties installed to provide strain relief?
Rear plastic safety cover installed?
PAGE 14
HDN HIGH DENSITY NETWORK DC DISTRIBUTION
InstallatIon and operatIon Manual: product specIfIcatIons
Figure 15. HDN A/B Isolated Input Connection Detail
FRONT VIEW
REAR VIEW
TOP VIEW
INPUT A
INPUT B
ALARM
TOUCH SCREEN TO OPERATE
A POWER INPUT LED
B POWER INPUT LED
BREAKER TRIP/ALARM LED
SIDE VIEW
1.000
CHASSIS GROUND
THREADED FOR 3/8-16
MOUNTING BRACKET
SCREWS REMOVE TO
ADJUST TO 23" WIDTH
A HOT INPUT -48V
B HOT INPUT -48V
OUTPUT RETURNS +48V
HOT OUTPUT -48V
THREADED FOR 3/8-16
REAR VIEW WITH MOUNTING
BRACKETS REMOVED FOR CLARITY
8p8C (RJ45)
CONTACTS
1/4-20 STUDS,
5/8” CENTERS
ALARM / CAN BUS JACKS
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Alpha HDN 300/600 Installation guide

Alpha
Brand
Alpha
Model
HDN 300/600
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents