Sanyo SAP–K302A Technical & Service Manual

Brand: Sanyo

Model: SAP–K302A

Category: Split-system air conditioners

Type: Technical & Service Manual

This manual is also suitable for

Sanyo SAP–K302A is a split system air conditioner designed to provide efficient and comfortable cooling for your home. With a cooling capacity of 29,000 BTU/h, it can effectively cool large rooms and maintain a comfortable temperature even on the hottest days. The air conditioner features a rotary compressor, which is known for its durability and energy efficiency. It also has a washable, anti-mold air filter that helps to keep your indoor air clean and fresh.

TECHNICAL & SERVICE MANUAL

SAP–K303A + SAP–C303A

FILE NO.

REFERENCE NO. SM700644

Indoor Unit Outdoor Unit

SPLIT SYSTEM AIR CONDITIONER

SAP–K303A SAP–C303A

Destination: Australia

Outdoor Model No. Product Code No.

SAP–C303A–A 1 852 098 62

Indoor Model No. Product Code No.

SAP–K303A–A 1 852 098 83

AIR CO

DITIONER

Important!

Please Read Before Starting

This air conditioning system meets strict safety and

operating standards. As the installer or service person,

it is an important part of your job to install or service the

system so it operates safely and efficiently.

For safe installation and trouble-free operation, you

must:

●Carefully read this instruction booklet before

beginning.

●Follow each installation or repair step exactly as

shown.

●Observe all local, state, and national electrical codes.

●Pay close attention to all warning and caution notices

given in this manual.

This symbol refers to a hazard or

unsafe practice which can result

in severe personal injury or

death.

This symbol refers to a hazard or

unsafe practice which can result

in personal injury or product or

property damage.

If Necessary, Get Help

These instructions are all you need for most installation

sites and maintenance conditions. If you require help

for a special problem, contact our sales/service outlet

or your certified dealer for additional instructions.

In Case of Improper Installation

The manufacturer shall in no way be responsible for

improper installation or maintenance service, including

failure to follow the instructions in this document.

Special Precautions

When Wiring

ELECTRICAL SHOCK CAN CAUSE

SEVERE PERSONAL INJURY OR

DEATH. ONLY A QUALIFIED,

EXPERIENCED ELECTRICIAN SHOULD

ATTEMPT TO WIRE THIS SYSTEM.

• Do not supply power to the unit until all wiring and

tubing are completed or reconnected and checked.

• Highly dangerous electrical voltages are used in this

system. Carefully refer to the wiring diagram and

these instructions when wiring. Improper connections

and inadequate grounding can cause accidental

injury or death.

• Ground the unit following local electrical codes.

• Connect all wiring tightly. Loose wiring may cause

overheating at connection points and a possible fire

hazard.

WARNING

CAUTION

WARNING

When Transporting

Be careful when picking up and moving the indoor and

outdoor units. Get a partner to help, and bend your

knees when lifting to reduce strain on your back. Sharp

edges or thin aluminum fins on the air conditioner can

cut your fingers.

When Installing…

…In a Ceiling or Wall

Make sure the ceiling/wall is strong enough to hold the

unit’s weight. It may be necessary to construct a strong

wood or metal frame to provide added support.

…In a Room

Properly insulate any tubing run inside a room to

prevent “sweating” that can cause dripping and water

damage to walls and floors.

…In Moist or Uneven Locations

Use a raised concrete pad or concrete blocks to

provide a solid, level foundation for the outdoor unit.

This prevents water damage and abnormal vibration.

…In an Area with High Winds

Securely anchor the outdoor unit down with bolts and a

metal frame. Provide a suitable air baffle.

…In a Snowy Area (for Heat Pump-type Systems)

Install the outdoor unit on a raised platform that is

higher than drifting snow. Provide snow vents.

When Connecting Refrigerant Tubing

• Use the flare method for connecting tubing.

• Apply refrigerant lubricant to the matching surfaces

of the flare and union tubes before connecting them,

then tighten the nut with a torque wrench for a leak-

free connection.

• Check carefully for leaks before starting the test run.

When Servicing

• Turn the power off at the main power box (mains)

before opening the unit to check or repair electrical

parts and wiring.

• Keep your fingers and clothing away from any

moving parts.

• Clean up the site after you finish, remembering to

check that no metal scraps or bits of wiring have

been left inside the unit being serviced.

Others

• Ventilate any enclosed areas when installing or

testing the refrigeration system. Escaped refrigerant

gas, on contact with fire or heat, can produce

dangerously toxic gas.

• Confirm upon completing installation that no

refrigerant gas is leaking. If escaped gas comes in

contact with a stove, gas water heater, electric room

heater or other heat source, it can produce

dangerously toxic gas.

CAUTION

Table of Contents
Page
1. OPERATING RANGE ............................................................................................................................... 1
2. SPECIFICATIONS
2-1. Unit Specifications.......................................................................................................................... 2
2-2. Major Component Specifications.................................................................................................... 3
2-3. Other Component Specifications.................................................................................................... 5
3. DIMENSIONAL DATA............................................................................................................................... 6
4. REFRIGERANT FLOW DIAGRAM .......................................................................................................... 8
5. PERFORMANCE DATA
5-1. Performance charts ....................................................................................................................... 9
5-2. Air Throw Distance Chart  .............................................................................................................. 10
5-3. Cooling Capacity  ........................................................................................................................... 11
6. ELECTRICAL DATA
6-1. Electrical Characteristics................................................................................................................ 12
6-2. Electric Wiring Diagram.................................................................................................................. 13
7. INSTALLATION INSTRUCTIONS
7-1. Installation Site Selection ............................................................................................................... 15
7-2. Remote Control Unit Installation Position....................................................................................... 17
7-3. Wiring instructions.......................................................................................................................... 18
8. FUNCTION
8-1. Room Temperature Control ........................................................................................................... 19
8-2. Dry Operation ................................................................................................................................ 20
8-3. Freeze Prevention ......................................................................................................................... 20
8-4. Outdoor Fan Speed Control  .......................................................................................................... 21
9. TROUBLESHOOTING
9-1. Check before and after troubleshooting  ........................................................................................ 22
9-2. Air conditioner does not operate .................................................................................................... 23
9-3. Some part of air conditioner does not operate  ..............................................................................27
9-4. Air conditioner operates, but abnormalities are observed ............................................................. 30
10.CHECKING ELECTRICAL COMPONENTS
10-1. Measurement of Insulation Resistance .......................................................................................... 30
10-2. Checking Continuity of Fuse on PCB Ass'y.................................................................................... 31
10-3. Checking Motor Capacitor ............................................................................................................. 31
11.MAINTENANCE
11-1. Changing Address of Remote Control in Indoor Unit ..................................................................... 32
INSTRUCTION MANUAL ........................................................................................................ 33
APPENDIX
ii

1. OPERATING RANGE

Temperature Indoor Air Intake Temp. Outdoor Air Intake Temp.

Cooling

Maximum 32°C D.B. / 23°C W.B. 43°C D.B.

Minimum 19°C D.B. / 14°C W.B. 19°C D.B.

2. SPECIFICATIONS

2-1. Unit Specifications

DATA SUBJECT TO CHANGE WITHOUT NOTICE.

Remarks: Rating conditions are:

Cooling: Indoor air temperature 27°C D.B. / 19°C W.B.

Outdoor air temperature 35°C D.B. / 24°C W.B.

Heating: Indoor air temperature 20°C D.B.

Outdoor air temperature 7°C D.B. / 6°C W.B.

Power Source 240 V Single phase 50Hz

Voltage rating V 240

Cooling

Capacity

kW 8.50

BTU/h 29,000

Air circulation (High) m

/h 1,110

Moisture removal (High) Liters/h 3.4

Available voltage range V 216 to 264

Running amperes A 13.2

Power input W 3,150

Power factor % 99

C.O.P. W/W 2.70

Compressor locked rotor amperes A 63

Controls / Temperature control Microprocessor / I.C. thermostat

Control unit Wireless remote control unit

Timer 1-hour OFF / 12-hour ON or OFF

Fan speeds Indoor / Outdoor 3 and Auto / Auto(Hi, Lo)

Airflow direction (Indoor)

Horizontal Manual

Vertical Auto

Air filter Washable, Anti-Mold

Compressor Rotary (Hermetic)

Refrigerant / Amount charged at shipment g R22 / 2,600

Refrigerant control Capillary tube

Operation sound

Indoor – Hi / Me / Lo dB-A 47 / 41 / 38

Outdoor – Hi dB-A 54

Refrigerant tubing connections Flare type

Max. allowable tubing length at shipment m 7.5

Refrigerant tube

Narrow tube mm (in.) 9.52 (3/8)

diameter

Wide tube mm (in.) 15.88 (5/8)

Refrigerant tube kit / Accessories Optional / Hanging wall bracket

Indoor Unit Outdoor Unit

Unit dimensions Height mm 330 735

Width mm 1,140 940

Depth mm 228 340

Package dimensions Height mm 325 826

Width mm 1,231 1,016

Depth mm 406 416

Weight Net

kg 18.0 71.0

Shipping

kg 20.0 77.0

Shipping volume m

0.16 0.35

Dimensions & Weight Features Electrical Rating Performance

Indoor Unit SAP–K303A

Outdoor Unit SAP–C303A

2-2. Major Component Specifications

2-2-1. Indoor Unit

DATA SUBJECT TO CHANGE WITHOUT NOTICE.

Part No. POW–K301A

Controls Microprocessor

Control circuit fuse 250 V – 3.15 A

Remote Control Unit RCS–4S4E–G

Type Cross-flow

Q´ty ... Dia. and length mm 1 ... ø100 / L847.4

Fan motor model ... Q´ty KFG4X–31B5P–C ... 1

No. of poles .... rpm (240V, High) 4 ... 1,270

Nominal output W 30

Coil resistance (Ambient temp. 20°C) Ω WHT – BRN : 103.3 WHT – VLT : 32.5

VLT – ORG : 75.5 ORG – YEL : 28.6

YEL – BLK : 18.9 BLK – PNK : 48.0

– : –

Safety

Type Thermal protector

devices Operating temp. Open °C 130 ± 8

Close Automatic reclosing

Run capacitor µF 1.0

VAC 440

Type Stepping motor

Model ... Q´ty MP24GA2 ... 2

Rating DC 12 V

Coil resistance (Ambient temp. 20°C) kΩ Each terminals (1–2, 1–3, 1–4, 1–5) : 400 ± 7%

Coil Aluminum plate fin / Copper tube

Rows 2

Fin pitch mm 1.3

Face area m2 0.214

Heat

Exch. Coil

Flap Motor Fan & Fan Motor

Circuit

Board

Ass´y

Indoor Unit SAP–K303A

2-2-2. Outdoor Unit

DATA SUBJECT TO CHANGE WITHOUT NOTICE.

Circuit Board Ass´y POW–C301A–A

Type Rotary (Hermetic)

Compressor model C–R240H5S 80669545

Nominal output W 2,400

Compressor oil ... Amount cc 4GSD–T or SAY–56T ... 1,350

Coil resistance (Ambient temp. 25°C) Ω C – R : 0.944

C – S : 1.732

Type Internal protector

Safety

Overload relay —

devices Operating temp. Open °C Automatic opening

Close °C Automatic reclosing

Operating amp.(Ambient temp. 25°C) —

Run capacitor ... Q´ty µF 35.0 ... 2

VAC 400 ... 2

Crank case heater —

Type Propeller

Q´ty ... Dia. mm 1 ... ø 460

Fan motor model ... Q´ty KFC6S–91D5P–C ... 1

No. of poles .... rpm (240V, High) 6 ... 780

Nominal output W 90

Coil resistance (Ambient temp. 20°C) Ω WHT – BRN : 129.0

WHT – YEL : 57.4

YEL – PNK : 22.1

Safety

Type Thermal protector

devices Operating temp. Open °C 130 ± 8

Close Automatic reclosing

Run capacitor µF 6.0

VAC 440

Coil Aluminum plate fin / Copper tube

Rows 2

Fin pitch mm 1.8

Face area m

0.630

External Finish Acrylic baked-on enamel finish

Heat

Exch. Coil

CompressorFan & Fan Motor

Outdoor Unit SAP–C303A

2-3. Other Component Specifications

Fuse

Cartridge type

Rating / Size

250V, 20A / ø6.4 x 30mm

Power Relay (PR)

EL1U

Coil rating

AC 200–240V, 50/60Hz

Contact rating

AC 277V, 30A

Thermistor (Air sensor)

PBC–41E–S14

Resistance kΩ

–20°C 40.1± 5% 20°C 6.5 ± 5%

–10°C 24.4 ± 5% 30°C 4.4 ± 5%

0°C 15.3 ± 5% 40°C 3.0 ± 5%

10°C 9.9 ± 5% 50°C 2.1± 5%

Outdoor Unit SAP–C303A

Thermistor (Room sensor)

DTN-TKS128B

Resistance kΩ

25°C 5.0 ± 3%

Thermistor (Coil sensor)

DTN-TKS131B

Resistance kΩ

0°C 15.0 ± 2%

Transformer (TR)

ATR-J105

Rating Primary

AC 230V, 50/60Hz

Secondary

19V, 0.526A

Capacity

10VA

Coil resistance Ω (at 21°C)

Primary (WHT – WHT): 205 ± 10%

Secondary (BRN – BRN): 2.0 ± 10%

Thermal cut-off temp.

150°C

Indoor Unit SAP–K303A

3. DIMENSIONAL DATA

Indoor Unit SAP–K303A

174

Center of tubing

hole (2 places)

Narrow tube ø9.52(3/8")

Wide tube ø15.88 (5/8")

228

135

330

1,140

Drain hose ø18

Remote control unit

Unit : mm

196

46.5

27.4

133.8

52 23

Outdoor Unit SAP–C303A

735

280

307

940

Unit : mm

Hole for anchor bolt ø13

Narrow tube service valve

ø9.52 (3/8

Wide tube service valve

ø15.88 (5/8

Refrigerant tubing outlet

Inter-unit wiring outlet

Power supply wiring outlet

400

380

50 50

340

110660170

Unit : mm

4. REFRIGERANT FLOW DIAGRAM

Insulation of Refrigerant Tubing

Because capillary tubing is used in the outdoor unit, both the

wide and narrow tubes of this air conditioner become cold. To

prevent heat loss and wet floors due to dripping of

condensation, both tubes must be well insulated with a

proper insulation material. The thickness of the insulation

should be a min. 8 mm.

After a tube has been insulated,

never try to bend it into a narrow

curve because it can cause the tube

to break or crack.

IMPORTANT

CAUTION

Wide tube

Thickness:

Min. 8 mm

Insulation

Narrow tube

Thickness:

Min. 8 mm

Indoor Unit SAP–K303A Outdoor Unit SAP–C303A

Compressor

Accumulator

Wide tube

service

valve

Indoor Unit Outdoor Unit

Muffler

Wide tube

O.D.

ø15.88 mm

(5/8 ")

Narrow

tube

service

valve

Narrow tube

O.D.

ø9.52 mm

(3/8")

Evaporator

Condenser

Capillary tube

5. PERFORMANCE DATA

5-1. Performance charts

Indoor Unit SAP–K303A

Outdoor Unit SAP–C303A

Outdoor

fan speed

HighLow

1.28 (12)

1.18 (11)

1.08 (10)

0.98 ( 9 )

0.89 ( 8 )

0.79 ( 7 )

0.69 ( 6 )

25 30 35 40 45 50

Outdoor inlet air D.B. temp. (°C)

Low pressure at wide tube serveice valve MPa (kgf/cm

0.59 ( 5 )

0.49 ( 4 )

0.39 ( 3 )

■ Cooling Characteristics

25 30 35 40 45 50

Outdoor inlet air D.B. temp. (°C)

Operating current (A)

Outdoor

fan speed

HighLow

Indoor inlet air

D.B. temp. (°C)

Indoor inlet air

D.B. temp. (°C)

● ...... Points of Rating condition

Black dots in above charts indicate the following rating conditions.

Cooling: Indoor air temperature 27°C D.B./19°C W.B.

Outdoor air temperature 35°C D.B./24°C W.B.

NOTE

5-2. Air Throw Distance Chart

Horizontal distance (m)

Axis air velocity (m/s)

Vertical distance (m)

Room air temp. : 27°C

Fan speed : High

0123456789

: Flap angle 0° , : Axis air velocity 0°

: Flap angle 30°, : Axis air velocity 30°

Indoor Unit SAP–K303A

5-3. Cooling Capacity

240V Single Phase 50Hz

Indoor Unit SAP–K303A

Outdoor Unit SAP–C303A

R AT ING C AP AC IT Y 8.50 kW

AIR F LOW R AT E 1110

E V AP OR AT OR C ONDE NS E R

E NT . T E MP . ° C OUT DOOR AMB IE NT T E MP . ° C

W.B . D.B . 30 35 40 43

T C 7.82 7.45 6.99 6.44

C M 2.54 2.73 2.93 3.17

21 S H C 5.09 4.88 4.63 4.33

15 23 S H C 5.60 5.39 5.14 4.84

25 S H C 6.11 5.90 5.65 5.35

27 S H C 6.63 6.41 6.16 5.86

29 S H C 7.14 6.92 6.67 6.37

31 S H C 7.65 7.43 6.99 6.44

T C 8.39 7.99 7.51 6.91

C M 2.62 2.81 3.01 3.25

21 S H C 4.58 4.36 4.11 3.81

17 23 S H C 5.09 4.87 4.62 4.32

25 S H C 5.60 5.38 5.13 4.83

27 S H C 6.11 5.89 5.64 5.34

29 S H C 6.62 6.41 6.16 5.85

31 S H C 7.13 6.92 6.67 6.36

T C 8.93 # 8.50 7.99 7.35

C M 2.70 2.89 3.11 3.34

21 S H C 4.02 3.80 3.56 3.26

19 23 S H C 4.53 4.32 4.07 3.77

25 S H C 5.04 4.83 4.58 4.28

27 S H C 5.55 5.34 5.09 4.79

29 S H C 6.06 5.85 5.60 5.30

31 S H C 6.57 6.36 6.11 5.81

T C 9.46 9.01 8.47 7.79

C M 2.77 2.98 3.11 3.44

23 S H C 3.96 3.75 3.50 3.20

21 25 S H C 4.47 4.26 4.01 3.72

27 S H C 4.98 4.77 4.52 4.23

29 S H C 5.49 5.28 5.03 4.74

31 S H C 6.00 5.79 5.54 5.25

T C 10.02 9.46 8.86 8.24

C M 2.84 3.05 3.28 3.52

23 25 S H C 3.85 3.61 3.36 3.11

27 S H C 4.36 4.12 3.87 3.62

29 S H C 4.87 4.63 4.38 4.13

31 S H C 5.38 5.14 4.89 4.64

TC : T otal C ooling C apacity (kW )

S HC : S ensible Heat C apacity (kW )

C M : C ompres s or Input (kW )

R ating conditions (#Mark) are

Outdoor Ambient T emp. 35° C D.B.

Indoor Unit E ntering Air T emp. 27° C D.B . / 19° C W.B .

6. ELECTRICAL DATA

6-1. Electrical Characteristics

Indoor Unit SAP–K303A

Outdoor Unit SAP–C303A

Indoor Unit Outdoor Unit Complete Unit

Fan Motor Fan Motor Compressor

Performance at 240V Single phase 50Hz

Rating Conditions Running Amps. A 0.330 0.660 12.21 13.2

Power Input kW 0.072 0.146 2.932 3.15

Full Load Conditions Running Amps. A 0.330 0.660 14.51 15.5

Power Input kW 0.072 0.146 3.472 3.69

Rating Conditions : Indoor Air Temperature 27°C D.B. / 19°C W.B.

Outdoor Air Temperature 35°C D.B.

Full Load Conditions : Indoor Air Temperature 32°C D.B. / 23°C W.B.

Outdoor Air Temperature 43°C D.B.

6-2. Electric Wiring Diagrams

To avoid electrical shock hazard, be sure to

disconnect power before checking, servicing

and/or cleaning any electrical parts.

WARNING

Indoor Unit SAP–K303A

TRANS

1 2 4 5 678

Controller

(

PCB Ass'y

)

Power transformer

Fan motor capacitor

Terminal plate

Room thermistor

Coil thermistor

Indicator lamp Ass'y

Upper flap motor

Lower flap motor*

*GREEN MAKE on

lower flap motor

Grille air outlet

(

Side View

)

Indoor Electrical Compornent Box

To avoid electrical shock hazard, be sure to

disconnect power before checking, servicing

and/or cleaning any electrical parts.

WARNING

Outdoor Unit SAP–C303A

Terminal

plate (8P)

Terminal plate (3P)

Compressor motor

capacitor (C1)

Compressor motor

capacitor (C2)

Power relay

Fan motor capacitor

Controller

(PCB Ass´y)

Clamp

Fuse (250V, 20A)

Outdoor Electrical Compornent Box

■

Parts Layout in Outdoor Unit

■

Compressor

Fan motor

Heat exchenger coil

Air thermistor

7. INSTALLATION INSTRUCTIONS

7-1. Installation Site Selection

To prevent abnormal heat

generation and the possibility

of fire, don’t place obstacles,

enclosures and grills in front

of or surrounding the air

conditioner in a way that may

block air flow.

AVOID:

●

direct sunlight.

●

nearby heat sources that may affect performance of

the unit.

●

areas where leakage of flammable gas may be

expected.

●

places where large amounts of oil mist exist.

DO:

●

select an appropriate position from which every

corner of the room can be uniformly air-conditioned.

(High on a wall is best)

●

select a location that will hold the weight of the unit.

●

select a location where tubing and drain pipe have the

shortest run to the outside.

●

allow room for operation and maintenance as well as

unrestricted air flow around the unit. (Fig. 1)

●

install the unit within the maximum elevation

difference (H) above or below the outdoor unit and

within a total tubing length (L) from the outdoor unit as

detailed Table 1 and Fig. 2a.

Indoor Unit

15 cm

min.

15 cm

min.

15 cm min.

INDOOR UNIT

Front View

INDOOR

UNIT

Tubing length (L)

OUTDOOR

UNIT

Elevation

difference (H)

Fig. 2

Fig. 2a

Fig.1

WARNING

Table 1

* If total tubing length becomes 7.5 to 30 m (max.), charge additional refrigerant (R22) by 60 g/m.

No additional charge of compressor oil is necessary.

Model

Max. Allowable

Tubing Length at

Shipment (m)

Limit of Tubing

Length (L)

(m)

Limit of Elevation

Difference (H)

(m)

Required Amount of

Additional Refrigerant

(g/m)*

C303 30

Minimum height

from floor level

1.5m

Indoor Unit

Wall

Floor level

For stable operation of the

air conditioner, do not

install wall-mounted type

indoor units less than

1.5m from floor level.

CAUTION

Fig. 2b

7.5

15 60

AVOID:

●

heat sources, exhaust fans, etc. (Fig. 3)

●

damp, humid or uneven locations.

DO:

●

choose a place as cool as possible.

●

choose a place that is well ventilated.

●

allow enough room around the unit for air

intake/exhaust and possible maintenance.

(Figs. 4a and 4b)

●

provide a solid base (concrete block, 10

40 cm

beams or equal), a minimum of 10 cm above ground

level to reduce humidity and protect the unit against

possible water damage and decreased service life.

(Fig.5)

●

use lug bolts or equal to bolt down unit, reducing

vibration and noise.

Outdoor Unit

Outdoor unit

Hot air

Heat source

Exhaust fan

Fig. 3

Min.

1 cm

Min.

1 cm

Min.50 cm

Min.10 cm

Air in

Air

discharge

Anchor bolts

(4 pieces)

Min. 10 cm

Min.

2 m

Min.

2 m

Obstacle above

Ground

Obstacle

Air

dis-

charge

Side View

Fig. 4b

Required space around the unit.

Top View

Fig. 4a

Fig. 5

7-2. Remote Control Unit Installation Position

The remote control unit can be operated from either a non-fixed position or a wall-mounted position.

To ensure that the air conditioner operates correctly, do not install the remote control unit in the following places:

●

In direct sunlight

●

Behind a curtain or other place where it is covered

●

More than 8 m away from the air conditioner

●

In the path of the air conditioner's airstream

●

Where it may become extremely hot or cold

●

Where it may be subject to electrical or magnetic interference

●

Where there is an obstacle between the remote control unit and air conditioner (since a check signal is sent

from the remote control unit every 5 minutes)

Attaching the remote control unit to wall

Before mounting the remote control unit, press the ON/OFF operation button at the mounting location to make

sure that the air conditioner operates from that location (Fig.6). The indoor unit should make a beeping sound

to indicate that it has received the signal.

Fig.6

Rear side

Hole

To prevent loss of the remote control

unit, you can connect the remote

control unit to the mount by passing

a string through the remote control

unit and attachment hole.

Remote control

unit mount

Mounting screws

4 x 16 (included)

Press

Set in

place

To take out the remote control unit, pull it forward.

Page is loading ...

Sanyo SAP–K302A Technical & Service Manual

Brand: Sanyo

Model: SAP–K302A

Category: Split-system air conditioners

Type: Technical & Service Manual

This manual is also suitable for

Download PDF

report

Sanyo SAP–K302A Technical & Service Manual

This manual is also suitable for

Sanyo SAP–K302A Technical & Service Manual

Related papers

Other documents