Triax DVB 250 T Owner's Instructions Manual

O w n e r’s

I n s t r u c t i o n s

T R I A X

DVB 250 T

Digital Terrestrial Receiver

MAIN SUPPLY Use only 90-250V AC 50/60Hz.

CABLE Use standard certified cables to prevent any malfunction of

the STB.

LOCATION Keep the STB inside and away from potential hazards such as

houseplants, lightning, raining and direct sunlight.

CLEANING 1. Always disconnect the STB power cord from the wall socket

before cleaning it.

2. Use a light damp cloth(no solvents)to clean the case.

OVERLOADING Do not overload wall outlets, extension cords or adapters.

These can cause fire or electrical shock.

VENTILATION 1. Do not block ventilation slots of STB.

2. Do not place the STB on soft furnishings or carpets.

3. Ensure that a free airflow is maintained around the STB.

4. Do not allow the STB to be exposed to direct sunlight or a heater.

5. Do not stack other electronic equipment on top of the STB.

LIQUIDS Keep liquids away from the STB.

Apparatus shall not be exposed to dripping or splashing and

no objects filled with liquids, such as vases, shall be placed

on the apparatus.

Safety Instructions

This Digital Satellite Receiver, normally referred to as a set-top-box (STB), has been

manufactured to meet international safety standards.

Please read the following safety instructions carefully before you handle the STB.

LIGHTNING 1. The STB must remain connected at all times to the power

supply and TV antenna.

2. However, Manufacture's instructions for safeguarding other

equipments connected to the STB, TV set, etc., must be

followed during the lightning.

3. Ensure lightning protection devices for the terrestrial

antenna, mains, and LNB are installed.

SERVICING 1. Service should be carried out by authorised service engineer.

T R I

A

X

- Digital Terrestrial Receiver

4

Digital Terrestrial R

Understanding the Remote Control Unit

..........................................6 ~ 7

Connecting Your Equipment

..................................................................

8

Front Panel......................................................................................................8

Rear Panel

.......................................................................................................

9

Connection

......................................................................................................

10 ~ 12

Setting Up Your System

...........................................................................13

Menu Tree

........................................................................................................

13

Automatic Channel Search for Television Services....................................14

Manual Channel Search

.................................................................................

14

Basic Function................................................................................................15 ~ 17

Menu Operation

...........................................................................................

18

Main Menu

.......................................................................................................

18

Channel List....................................................................................................19

Channel Information.......................................................................................20

Channel Sorting

..............................................................................................

20 ~ 22

Channel Editing..............................................................................................22 ~ 27

1. Delete Channels

..................................................................................

23

2. Lock Channels

.....................................................................................

24

3. Edit Favorite Channels

........................................................................

25

4. Organize Channel Categories.............................................................25

5. Move the Position of Channels

............................................................

26

6. Rename Channels

...............................................................................

27

Contents

Receiver

Digital Terrestrial Receiver -

T R I

A

X

5

Program Guide................................................................................................28

1. Now/Next EPG

....................................................................................

28

2. Weekly EPG........................................................................................29

Setup

................................................................................................................

30

1. Menu Language

...................................................................................

30

2. SCART Output.....................................................................................31

3. Screen Type

.........................................................................................

31

4. Banner Time

........................................................................................

31

5. RF Output

............................................................................................

32

6. Other Setting .......................................................................................32 ~ 34

Installation.......................................................................................................35

Channel Search..............................................................................................35 ~ 38

Change PIN Code

..........................................................................................

38

Parental Lock

..................................................................................................

39

Receiver Lock.................................................................................................39

Factory Reset

.................................................................................................

39

TELETEXT Navigation

....................................................................................

40

TroubleShooting

..........................................................................................

41

Technical specifications

..........................................................................42 ~ 43

T R I

A

X

- Digital Terrestrial Receiver

6

Digital Terrestrial R

Understanding the Remote Control Unit

Remote Control Unit

TELETEXT

TV/STB

1 8

FAVORITE

1 9

MUTE

1 6

CHANNEL

UP/DOWN

1 5

MENU

1 4

PRE-CHANNEL

1 3

SOUND

1 2

EXIT

11

NUMERIC

Buttons

1 7

VOLUME UP/DOWN

STANDBY

EPG

INFORMATION

SUBTITLE

PAGE UP/DOWN

LEFT/RIGHT

OK

TV/RADIO

1

2

3

4

5

7

6

9

8

1 0

Receiver

Digital Terrestrial Receiver -

T R I

A

X

7

Understanding the Remote Control Unit

STANDBY

T

o switch between Operation and

Standby mode.

EPG

To display the TV/Radio program guide.

INFORMATION (Green)

To display the program information box on

the screen .

SUBTITLE (Red)

To select the subtitle language list for the

current channel.

PAGE UP/DOWN

To move up or down a page in the

channel list.

LEFT/RIGHT

To move left or right highlight

marked cursor

.

OK

To confirm your choice.Simple channel list.

TELETEXT

To navigate teletext pages.

TV/STB

To switch between TV and STB receive

mode.

TV/RADIO

T

o switch between

TV program and RADIO

only receiving mode.

NUMERIC

Buttons

T

o select the channel and enter the channel

information and PIN Code.

EXIT

To return to the normal viewing mode from a

menu.

SOUND (Yellow)

T

o select the sound track list in the current

channel.

PRE-CHANNEL (Blue)

T

o return to the previous channel.

MENU

T

o display the Main Menu on the screen or

return to the previous menu.

CHANNEL UP/DOWN

T

o change channels up and down.

VOLUME UP/DOWN

To increase or decrease the volume.

FAVORITE

To move among the favorite lists.

MUTE

T

o enable or disable the audio.

Note! :

The design of the Remote Control Unit may be changed without

any notice in advance.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

T R I

A

X

- Digital Terrestrial Receiver

8

Digital Terrestrial R

Connecting Your Equipment

Front Panel

2

1

3

4

5

STAND-BY To Switch between Operation and Standby mode.

CH - / + To change channels up and down.

To move up or down highlight marked cursor.

VOL - / + To increase or decrease the volume.

To move left or right highlighted cursor .

LIST/OK To confirm your choice or display the channel list.

TV/RADIO To switch between TV program and Radio only receiving mode.

3

4

5

1

2

Receiver

Digital Terrestrial Receiver -

T R I

A

X

9

Connecting Your Equipment

Rear Panel

1

2

3

4

5

6

7

8

9

10

3

9

8

1 0

ANT IN To connect digital TV antenna input.

LOOP Used to connect a RF signal from the STB to either the RF input jack

THROUGH (antenna) on your television or to the STB (RF Loop In).

RS-232 To connect to a personal computer for software upgrade.

AUDIO To connect audio R/L to a TV or an Audio Amp or System.

VIDEO To connect video to a TV using RCA jack.

TV OUT To connect to TVvia a conaxial cable for analogue broadcast loop

through.

ANT IN To connect analogue

TV antenna via coaxial cable.

TV To connect this port to that of a TV via scart cable.

VCR To connect this port to that of a VCR via scart cable.

OPTICAL To connect S/PDIF cable.

1

2

4

5 6 7

T R I

A

X

- Digital Terrestrial Receiver

1 0

Digital Terrestrial R

Connecting Your Equipment

Connection

How to connect your STB to various systems

There are several ways of connecting the STB to your

TV

, VCR and/or Hi-Fi System.

Consult your local supplier for assistance in setting-up your system best suited to

your requirements.

1. STB to a TV

1. Simple connection to the television set.

There

a

re 3 methods.

( a ) Connect STB via RCAlead (as supplied)

Connect the RCAlead (3 colours) to the video & audio outputs on the STB.

The other side shall connect to the television AV input(i.e.the audio and video input).

(b) Connect STB via SCART connector (not supplied)

Simply connect the SCART lead from TV (on STB) to the SCART connector usually found

on the rear of your television.

2. Antenna & Loop through connection

(c) ANT IN for Digital : Connect outdoor antenna via RF cable to take digital broadcast.

(d) ANT IN for Analogue : Connect outdoor antenna via RF cable to take analogue broadcast.

(e) LOOP THROUGH : Connect via RF cable to the other STB to pass through digital

signal from antenna for digital broadcast.

(f) TV OUT : Connect via RF cable to the RF IN on the TV or VCR to pass

through analogue signal from Antenna for analogue broadcast.

STB to a TV Set

Digital Terrestrial Receiver -

T R I

A

X

1 1

2. STB to a VCR

Simple connection to a VCR for recording.

There are 2 methods of connecting your video cassette & recorder

.

(a)

Connect VCR via RCA

connection (lead supplied)

Connect the RCA

lead (3 colours)

to the video & audio outputs on the STB

and the other end to the video & audio inputs on the VCR.

Make sure your VCR is set to V

ideo Input (or

A

V input) to view your STB.

Consult your VCR user manual for details.

(b)

Connect VCR via SCART (not supplied)

Simply connect one end of the SCAR

T

lead to the STB as shown and the other

end of the SCAR

T

connector to the VCR (usually found on the rear).

STB to a VCR

Receiver

Connecting Your Equipment

T R I

A

X

- Digital Terrestrial Receiver

1 2

Digital Terrestrial R

Connecting Your Equipment

3. STB to a HI-FI System

(a) Connect VCR via RCA

connection (lead supplied)

Use a standard RCA

lead to connect

Audio R & Audio L

outputs on the STB to

the

AUX input on the HI-FI System.

The

AUX input may sometimes be called also LINE IN,

TV IN or VCR IN.

(b) Connect VCR via OPTICAL(S/PDIF)

Use optical cable to connect STB with Hi-Fi for digital audio sound.

STB to a HI-FI System

Digital Terrestrial Receiver -

T R I

A

X

1 3

Menu Tree

Receiver

Setting up Your System

T R I

A

X

- Digital Terrestrial Receiver

1 4

Digital Terrestrial R

Setting up Your System

Automatic Channel Search for T

elevision Services

You can automatically detect and save all channels as follows:

• Connect STB as per pages 10 to 12 (as applicable).

•

Turn on the power of STB and other devices

connected to the STB.

•

Press Red (auto) button, then STB will automatically

search all channels and save them into the channel list.

•

Select Channel Search in the Installation Menu.

• Enter the PIN Code. (Factory PIN code is ‘0000’)

•

Select channel search in the Installation Menu.

•

Enter the PIN code. (Factory PIN Code is ‘0000’)

•

Select the Television Service you want to search by

pressing the UP/DOWN buttons and OK button.

•

Press Green (Manual) button, then STB

will automatically search all channels and save them

into the Channel List.

Manual Channel Search

You can automatically search as save all channels as follows :

• Select Channel Search in the Installation Menu.

• Enter the PIN Code. (Factory PIN Code is ‘0000’)

Power On

Main Menu/Installation

Channel search / Auto

Main Menu/Installation

Channel Search / Manual

System Connection

Digital Terrestrial Receiver -

T R I

A

X

1 5

Receiver

Setting up Your System

Basic Function

Channel (Service) Change

1. Press the numeric buttons (0~9) on the remote control to select the channel no.

you want.

2. Press the OK button on the Remote Control Unit and select the channel you want from

the Channel List.

3. Press the CH+/CH- buttons on the Remote Control Unit to select the channel you want.

4. To change the TV/RADIO channel, press the TV/RADIO button on the Remote

Control Unit.

Information Screen

After the television channels have been programmed, you will see the information(banner)

box each time you switch channels.

Logical Channel Number

Channel Name

Network Name

Parental Rating

Signal Quality

Day/Time

Indicator

Sound

Subtitle (DVB)Teletext

Signal Quality

Banner 1

Banner 2

T R I

AX

- Digital Terrestrial Receiver

1 6

Digital Terrestrial R

Setting up Your System

Volume Control / Mute

Press the VOL+/VOL- buttons to control the volume.

To temporarily stop the volume, press the MUTE button.

To cancel mute, press the MUTE button again or press the VOL+/VOL- buttons.

Sound Track

When you want to change the Audio Language of current channel, press the

SOUND( ) button.

Use the UP/DOWN buttons on the Remote Control Unit to select the audio language

you want.

Press OK and use the LEFT/RIGHT buttons on the Remote Control Unit to select the sound type

(Stereo, Mono, Left, Right).

EXIT ro SOUND button : Exit this menu

Digital Terrestrial Receiver -

T R I

A

X

1 7

Receiver

Setting up Your System

Subtitle Language

To select subtitle language, press the SUBTITLE( ) button.

Use the UP/DOWN buttons on the Remote Control Unit to select the Subtitle language

you want.

To stop the subtitle, select the Off on the submenu.

EXIT or SUBTITLE button : Exit this menu

T R I

A

X

- Digital Terrestrial Receiver

1 8

Digital Terrestrial R

Menu Operation

3. You can move into the desired submenu using UP/DOWN buttons.

4. Press the OK button to confirm your selection.

5. Press the MENU button to return to the previous menu or press the EXIT button to quit

the Menu system completely.

Note

Press the OK button when there is no Menu

Window on the screen, and the simple channel

list will appear on the screen.

Main Menu

1. Turn on TV and your STB, after you have connected all peripheral devices to it.

2. Press the MENU button on the Remote Control Unit. You will see the Main Menu on the

TV screen as follow:

Digital Terrestrial Receiver -

T R I

A

X

1 9

Receiver

Channel List

This menu consist of All Channel List, Channel Information, Channel Sorting and Channel

Editing.

Select Channel List in the Main Menu. Then you will get a Channel List as follows ;

The color button corresponds to the following

channel function.

Red button : All Channel Lists

Green button : Channel Information

Yellow button : Channel Sorting

Blue button : Channel Editing

You can get the information of channel number, channel name, and the scrambled

channel (The channel number is marked in red).

This menu helps you to easily select the channel that you want to watch.

To watch a specific channel, first select the specific channel that you wish to watch by

pressing the UP / DOWN / LEFT / RIGHT buttons, and then press OK button on the

Remote Control Unit. Also press the PAGE UP/DOWN buttons.

Main menu shows the following information.

Channel List

Shows the whole channel list stored in STB.

Shows the Channel Information and Channel Sorting.

Shows the information of Now

, Next Programs and W

eekly Programs.

Sets Menu Language, SCAR

T Output, Screen T

ype, Banner

Time, RF

Output and Other Setting.

Sets Channel Search, Change PIN Code, Parental Lock, Receiver

Lock and Factory Reset.

Setup

Installation

Program Guide

Menu Operation

T R I

A

X

- Digital Terrestrial Receiver

2 0

Digital Terrestrial R

Menu Operation

Channel Information

This mode helps you to watch the detailed information of a specific channel.

To watch a detailed information of a specific channel:

Press the Green button in the Channel List menu, and Channel Information window

will be displayed.

Press the UP/DOWN

buttons to select the channel you want.

The detailed information will appear on the right display window.

It consists of the following items: Favorite Channel, Category, Sound, Subtitle,

TTX(TELETEXT), PID(Video, Audio and PCR) and Scrambling symbol.

Subtitle, Teletext, Scrambling symbol: These are automatically displayed when the

broadcasting station provides appropriate information.

Channel Sorting

This mode displays channels according to the respective classifications desired by the

user through its function of sorting diverse information that each channel is furnished with.

Select the Yellow button in the Channel List menu, and the cursor toggles between

channel and channel sorting menu.

Page is loading ...

Triax DVB 250 T Owner's Instructions Manual

Triax DVB 250 T Owner's Instructions Manual

Related papers

Other documents