Dentsply Sirona CEREC SpeedGlaze Operating instructions

Brand: Dentsply Sirona

Model: CEREC SpeedGlaze

Type: Operating instructions

Dentsply Sirona CEREC SpeedGlaze is a glazing spray for dental restorations made from Sirona CAD/CAM materials. It can be used on crowns, inlays, onlays, partial crowns, and bridges in both the anterior and posterior tooth regions. The spray creates a thin, even layer of glaze that is melted during the firing process to create a smooth, shiny surface. CEREC SpeedGlaze is easy to use and can help you achieve beautiful, long-lasting results.

kÉï=~ë=çÑW=

léÉê~íáåÖ=fåëíêìÅíáçåë

MTKOMNS

`bob`=péÉÉÇdä~òÉ

båÖäáëÜ

Operating Instruct ions

65 92 617 D 3487

2D 3487.201.16.02.02 07.2016

Table of contents Sirona Dental Systems GmbH

Operating Instructions CEREC SpeedGlaze

Table of contents

1Product description................................................................................................... 3

2Intended use, indications and contraindications....................................................... 4

2.1 Intended use ................................................................................................. 4

2.2 Indications ..................................................................................................... 4

2.3 Contraindications .......................................................................................... 4

3Composition, note, side effects ................................................................................ 5

3.1 Composition .................................................................................................. 5

3.2 General note ................................................................................................. 5

3.3 Side effects ................................................................................................... 5

4Application procedure............................................................................................... 6

5Error prevention........................................................................................................ 8

6Hazard warnings and storage instructions ............................................................... 9

6.1 Hazard warnings ........................................................................................... 9

6.2 Storage instructions ...................................................................................... 9

7Preparation of Operating Instructions....................................................................... 10

65 92 617 D 3487

D 3487.201.16.02.02 07.2016 3

Sirona Dental Systems GmbH 1Product description

Operating Instructions CEREC SpeedGlaze

båÖäáëÜ

1Product description

The CEREC SpeedGlaze spray is used for glazing fully-anatomical

restorations. The spray applies a layer of glass powder to the sprayed

surface, which is then melted on in the subsequent firing phase.

65 92 617 D 3487

4D 3487.201.16.02.02 07.2016

2Intended use, indications and contraindications Sirona Dental Systems GmbH

2.1Intended use Operating Instructions CEREC SpeedGlaze

2Intended use, indications and

contraindications

2.1 Intended use

Glazing of individually designed restorations from dental ceramics.

2.2 Indications

The CEREC SpeedGlaze spray is suitable for glazing dental restorations

from the Sirona-CAD/CAM materials: CEREC Zirconia, inCoris TZI C,

CEREC Blocs C, CEREC Blocs C PC and CEREC Blocs C In. The

CEREC SpeedGlaze spray may only be used extra-orally. Indications in

dentistry areas: Crowns, inlays, onlays, partial crowns and bridges in the

anterior and posterior tooth region.

2.3 Contraindications

● Application of the spray on zirconium oxide in an unsintered condition

● Application on ceramic materials with low melting points

● Intra-oral application

65 92 617 D 3487

D 3487.201.16.02.02 07.2016 5

Sirona Dental Systems GmbH 3Composition, note, side effects

Operating Instructions CEREC SpeedGlaze 3.1Composition

båÖäáëÜ

3Composition, note, side effects

3.1 Composition

Glaze material, propulsion gas: Isobutane

3.2 General note

Failure to observe the above-listed contraindications and processing

instructions may result in failure.

3.3 Side effects

There are no known side effects. In the case of a known allergy to one of

the ingredients, do not use the CEREC SpeedGlaze spray.

65 92 617 D 3487

6D 3487.201.16.02.02 07.2016

4Application procedure Sirona Dental Systems GmbH

Operating Instructions CEREC SpeedGlaze

4Application procedure

Preparing the restoration before spraying:

1. Clean the surface of the restoration beforehand with ultrasound in a

water bath or with a steam jet. The restoration must be dry and free

of impurities.

2. If customization with staining is desired, this staining must be applied

before spraying, for example using Vita Akzent Plus or Ivoclar IPS

e.max Crystall Shades & Stains.

Spraying process:

1. Shake the container well immediately before use until the beads can

be heard inside the bottle.

2. Hold the restoration firmly on the inside with tweezers or hold it in

position on the firing tray using the CEREC SpeedPaste.

3. Keep the can as upright as possible during the spraying process.

4. The distance between the nozzle and the object should be approx.

10cm.

5. Apply an even coat of spray from all sides in short bursts directly on

to the surface of the restoration. Shake the container again in

between sprays.

6. The fine, thin and equal application should be visible on the surface.

7. Should the glaze slip reach the interior surfaces of the restoration,

remove it using a dry short-haired brush.

8. You can now fire the restoration in accordance with the instructions.

9. If another application of spray is necessary after the firing, the spray

can be applied once more in the same way.

65 92 617 D 3487

D 3487.201.16.02.02 07.2016 7

Sirona Dental Systems GmbH 4Application procedure

Operating Instructions CEREC SpeedGlaze

båÖäáëÜ

Notes on glaze firing

CEREC SpeedFire*:

* Programs for glazing Sirona ceramics are set for CEREC SpeedFire

and cannot be changed by the user.

Vita Vacumat and Ivoclar Programat**:

** Please refer to the instructions for calibrating the furnaces, firing

parameters may vary.

Product Temp.

°C

→

min.

CEREC Zirconia 900 2:00

inCoris TZI C 900 2:00

CEREC Blocs C / CEREC Blocs C PC 850 2:00

CEREC Blocs C In 850 2:00

Product Predr.

°C

→

min.

↗

min.

↗

°C/min.

Temp.

°C

→

min.

CEREC Zirconia 500 4:00 5:00 80 900 1:00

inCoris TZI C 500 4:00 5:00 80 900 1:00

CEREC Blocs C /

CEREC Blocs C PC

400 4:00 10:00 45 850 1:00

CEREC Blocs C In 400 4:00 10:00 45 850 1:00

65 92 617 D 3487

8D 3487.201.16.02.02 07.2016

5Error prevention Sirona Dental Systems GmbH

Operating Instructions CEREC SpeedGlaze

5Error prevention

In addition to the glazing agent, the CEREC SpeedGlaze spray contains

an orange indicator color. This is intended to help better review the even

application of the glazing agent. The pigment burns off without residue

and has no impact on the color of the restoration.

If the CEREC SpeedGlaze is applied too thick, this may result in chipping

during or after the glaze is fired.

If the CEREC SpeedGlaze is applied too thick, this may lead to milky

whitening.

65 92 617 D 3487

D 3487.201.16.02.02 07.2016 9

Sirona Dental Systems GmbH 6Hazard warnings and storage instructions

Operating Instructions CEREC SpeedGlaze 6.1Hazard warnings

båÖäáëÜ

6Hazard warnings and storage instructions

6.1 Hazard warnings

● Use in well ventilated rooms.

● The can is pressurized.

● Protect against direct sunlight and temperatures exceeding 50°C.

● Do not open by force or burn, even after use.

● Keep out of the reach of children.

6.2 Storage instructions

● See the bottom of the can for the expiration date.

● Do not use the CEREC SpeedGlaze after the expiration date.

● Keep away from direct sunlight.

65 92 617 D 3487

10 D 3487.201.16.02.02 07.2016

7Preparation of Operating Instructions Sirona Dental Systems GmbH

Operating Instructions CEREC SpeedGlaze

7Preparation of Operating Instructions

The material was developed for use in the dental area and must be

applied as specified in the Operating instructions.

The manufacturer assumes no liability for damage ensuing from

misapplication or improper use of this product.

Furthermore, the user is obliged to test the material for suitability and

applicability for the intended purposes under his or her own responsibility

before using it, especially if these purposes are not specified in the

Operating Instructions.

tÉ=êÉëÉêîÉ=íÜÉ=êáÖÜí=íç=ã~âÉ=~åó=~äíÉê~íáçåë=ïÜáÅÜ=ã~ó=ÄÉ=êÉèìáêÉÇ=ÇìÉ=íç=íÉÅÜåáÅ~ä=áãéêçîÉãÉåíëK

«=páêçå~=aÉåí~ä==póëíÉãë=dãÄe péê~ÅÜÉW ÉåÖäáëÅÜ mêáåíÉÇ=áå=dÉêã~åó

a=PQUTKOMNKNSKMOKMO MTKOMNS ûKJkêKW= MMM=MMM

páêçå~=aÉåí~ä=póëíÉãë=dãÄe `çåí~Åí=áå=íÜÉ=rp^W

c~Äêáâëíê~≈É=PN

aJSQSOR=_ÉåëÜÉáã

dÉêã~åó

páêçå~=aÉåí~äI=fåÅK

QUPR=páêçå~=aêáîÉ

`Ü~êäçííÉI=k`=OUOTP

rp^

lêÇÉê=kçSR=VO=SNT=a=PQUT

ïïïKëáêçå~KÅçã

Dentsply Sirona CEREC SpeedGlaze Operating instructions

Dentsply Sirona CEREC SpeedGlaze Operating instructions

Dentsply Sirona CEREC SpeedGlaze Operating instructions

Related papers

Other documents