3M Chairside Zirconia Operating instructions

3M
Brand
3M
Model
Chairside Zirconia
Type
Operating instructions

3M Chairside Zirconia is a high-quality dental zirconia designed for use in the fabrication of single-unit crowns, three-unit bridges, inlays/onlays, and veneers. It is esthetically designed to match the VITA® classical shade guide, making it easy to match the restoration to the patient's natural tooth shade.

Capabilities:

  • Pre-shaded in Bleach, A1, A2, A3, A3.5, B1, C1, and D2 shades
  • Wall thickness of at least 0.8 mm
  • Bridge connector cross section of at least 12 mm2 for anterior restorations and 14 mm2 for posterior restorations
  • Can be conventionally cemented with 3M™ RelyX™ Luting Plus Resin Modified Glass Ionomer Cement or 3M™ RelyX™ Unicem 2 Self-Adhesive Resin Cement

3M Chairside Zirconia is a high-quality dental zirconia designed for use in the fabrication of single-unit crowns, three-unit bridges, inlays/onlays, and veneers. It is esthetically designed to match the VITA® classical shade guide, making it easy to match the restoration to the patient's natural tooth shade.

Capabilities:

  • Pre-shaded in Bleach, A1, A2, A3, A3.5, B1, C1, and D2 shades
  • Wall thickness of at least 0.8 mm
  • Bridge connector cross section of at least 12 mm2 for anterior restorations and 14 mm2 for posterior restorations
  • Can be conventionally cemented with 3M™ RelyX™ Luting Plus Resin Modified Glass Ionomer Cement or 3M™ RelyX™ Unicem 2 Self-Adhesive Resin Cement
Indications
• Single-unit crowns
• Three-unit bridges with one pontic supported on each side by a crown
• Inlays/onlays and veneers
Tooth Preparation
Follow the recommendations of professional associations when preparing
all-ceramic restorations. A chamfer preparation is recommended.
Design Parameters
The following design specications must be fullled for the nished
restorations:
Wall thickness Bridge connector cross section
Anterior ≥ 0.8 mm ≥ 12 mm
2
Posterior ≥ 0.8 mm ≥ 14 mm
2
Esthetics designed to match the VITA
®
classical shade guide
Each zirconia block comes pre-shaded
in Bleach, A1, A2, A3, A3.5, B1, C1 and
D2 shades designed to match VITA
classical shades. The result? Easy
matching of 3M Chairside Zirconia
to each patient’s tooth shade.
Pre-treatment of bonding surface
Tip: After try-in, clean saliva contamination with NaOCI (ca.5%) and
rinse with water. Do not use phosphoric acid for cleaning. If you prefer,
sandblasting can be done after try-in to remove saliva contamination.
Cementation
Depending on the requirements, 3M
™
Chairside Zirconia restorations
may be conventionally cemented with 3M
™
RelyX
™
Luting Plus Resin
Modied Glass Ionomer Cement or 3M
™
RelyX
™
Unicem 2 Self-Adhesive
Resin Cement.
Sandblast with alumina, 30-50 μm grain
size at 2 bars (30PSI) to create a matte
appearance.
Clean with alcohol and dry with
oil-free air.
Maintain 0.8 mm minimum
wall thickness!
Minimum
0.8 mm
reduction
Chamfer preparation
Crown Quick Start Guide
3M
™
Chairside Zirconia
1. Prep the tooth and select the shade.
5. The scaling factor is shown on each block and
must be entered into the system prior to milling.
9. Remove all milling dust from all surfaces using
a soft articial hair brush.
2. Scan preparation.
6. The material can be wet or dry milled. Dry
milling is recommended. Clean milling chamber
before processing 3M
™
Chairside Zirconia to
avoid contamination. When wet milling, use
distilled or deionized water. Avoid contamination
from other milling materials.
10. Place the restoration in the furnace chamber with the occlusal or lingual
surface facing down. 3M
™
Chairside Zirconia can be fast red in high
temperature sintering furnaces, including the CEREC
®
SpeedFire furnace
(Dentsply Sirona) and Programat
®
CS4 furnace (Ivoclar Vivadent). With the
CEREC
®
SpeedFire furnace (compatible with CEREC
®
Software 4.6.0),
3M Chairside Zirconia has a fast sintering time of approximately 20 minutes
for a thin-walled crown.¹,² Refer to sintering parameters in the 3M Chairside
Zirconia Instructions for Use.
3. Design.
7. Use a diamond bur to separate the restoration
from the mandrel.
11. Use polishers suitable for zirconia restorations -OR- use a glaze
specically designed for zirconia restorations and suitable for use in
the CEREC
®
SpeedFire sintering furnace. Be sure to protect the internal
surface of the restoration with the required paste. Follow all manufacturers
instructions for glazing. If restoration is adjusted after try-in, be sure to
repolish the adjusted areas.
4. Color choice.
8. Carefully smooth the sprue area with rubber
points and cups.
Before using the products described, please refer to the instructions for use provided with the product packages.
OR
Crown Quick Start Guide
3M
™
Chairside Zirconia
3M Oral Care · 2510 Conway Avenue · St. Paul, MN 55144-1000 · USA · 1-800-634-2249 · 3M and RelyX are trademarks of 3M or 3M Deutschland GmbH. Used under license
in Canada.
All other trademarks are owned by other companies. Please recycle. Printed in U.S.A. © 3M 2019. All rights reserved. 70-2013-7121-1 (Rev.8/2019)
3M.com/ChairsideZirconia
  • Page 1 1
  • Page 2 2

3M Chairside Zirconia Operating instructions

3M
Brand
3M
Model
Chairside Zirconia
Type
Operating instructions

3M Chairside Zirconia is a high-quality dental zirconia designed for use in the fabrication of single-unit crowns, three-unit bridges, inlays/onlays, and veneers. It is esthetically designed to match the VITA® classical shade guide, making it easy to match the restoration to the patient's natural tooth shade.

Capabilities:

  • Pre-shaded in Bleach, A1, A2, A3, A3.5, B1, C1, and D2 shades
  • Wall thickness of at least 0.8 mm
  • Bridge connector cross section of at least 12 mm2 for anterior restorations and 14 mm2 for posterior restorations
  • Can be conventionally cemented with 3M™ RelyX™ Luting Plus Resin Modified Glass Ionomer Cement or 3M™ RelyX™ Unicem 2 Self-Adhesive Resin Cement
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents