Garmin SL30 Reference guide

Garmin
Brand
Garmin
Model
SL30
Type
Reference guide

This manual is also suitable for

Garmin SL30 is a Comm Nav System that combines the functions of a Comm Radio, Nav Radio, and OBS into one compact unit.

The SL30 has a large outer knob that controls frequency selection in MHz and a small inner knob that controls frequency selection in kHz. The SL30 also has a number of buttons that control various functions, such as the mode select button, the enter button, and the squelch button.

The SL30 can store up to 20 user-defined frequencies, which can be recalled by pressing the SEL button and turning the large outer knob. The SL30 also has a number of pre-programmed frequencies, such as the emergency channel and the weather channel.

Garmin SL30 is a Comm Nav System that combines the functions of a Comm Radio, Nav Radio, and OBS into one compact unit.

The SL30 has a large outer knob that controls frequency selection in MHz and a small inner knob that controls frequency selection in kHz. The SL30 also has a number of buttons that control various functions, such as the mode select button, the enter button, and the squelch button.

The SL30 can store up to 20 user-defined frequencies, which can be recalled by pressing the SEL button and turning the large outer knob. The SL30 also has a number of pre-programmed frequencies, such as the emergency channel and the weather channel.

Press SYS. Turn LARGE Knob to selection, then press ENTER.
System (SYS)
Nav Radio Info
Nav Audio Level
Nav/Com Mix Level
Additional CDI Info
Display Ident Over OBS
Turn LARGE Knob
Nav Software Ver
Com Software
DSP Software
Low Display Intensity
High Display Intensity
Turn LARGE Knob
System Info
VOR Equipment Test
Date of Last Test
Type of Test
Location
Bearing Error
1st Name
Last Name
Turn LARGE Knob
COM Options
RF Signal Level
Com Noise Level
Mic1 Squelch
Mic2 Squelch
Transmit Using...
Intercom Level
Sidetone Level
Headphone Level
Turn LARGE Knob
Operation Summary
Large Knob - MHz
Small Knob - kHz
Com Key - Monitor
Comm Mode
COM
Large Knob - MHz
Small Knob - kHz
Nav Key - Monitor
Nav Mode
NAV
System Info
Nav Options
Com Options
VOR Equip Test
System Mode
SYS
Large Knob - tens of degrees
Small Knob - ones of degrees
OBS Mode*
OBS
* Not available if system
is configured to use an
external CDI.
Apollo SL30 Quick Reference Guide
P/N 561-0262-00 Rev A
August 2003
2003 by Garmin AT, Inc.
Printed in the U.S.A.
All Rights Reserved
2345 Turner Rd., S.E.
Salem, OR 97302
Power/
Volume/
Squelch
Photocell
Frequency
Flip/Flop
Nav
Radio
OBS
Select
System
Settings
Active
Frequency
Large Outer
Knob
Small Inner
Knob
Comm
Radio
Bearing
Mode Select
Select
Standby
Frequency
Audio
Ident
Enter
To/From
To/From
Indication
Graphic
CDI
Function
Annunciators
Transmit
Annunciator
NAV/COMM
PULL SQUELCH
118.00 s136.00 135 to
POLLO
A
SL30
COM
SYS
NAV
OBS
SEL
T/F ID
ENT
A}}}
VOL
OFF
TX
Comm Frequencies
Auto Stored
List
(AUTO)
User
Memory
(USER)
Weather
Emerg.
Channel
Remote Comm
Frequencies
Turn LARGE Knob
, then turn SMALL knob
.
Press
.
SEL
Press to transfer into Standby. Press to transfer into Active.
ENT
Last
First
Last
First
Last
First
Last
First
Nav Frequencies
Auto Stored
List
(AUTO)
User
Memory
(USER)
Remote VOR
Frequencies
Turn LARGE Knob
, then turn SMALL knob .
Press .
SEL
DST
Data
Remote ILS
Frequencies
Press to transfer into Standby. Press to transfer into Active.
ENT
Last
First
Last
First
Last
First
Last
First
FAX (503) 364-2138
http://www.garminat.com
USA 800-525-6726
Canada 800-654-3415
International (503) 391-3411
Monitoring a Comm Frequency
The Comm Frequency Monitoring function allows you to monitor the Standby
Comm frequency for activity, while listening to the Active frequency.
Press the COM key while in the Comm function to listen to the Standby
frequency. A small “m” will replace the “s” in front of the Standby frequency.
Press the COM key a second time to exit. Note that changing modes (NAV,
SYS, etc.) will not disable the Comm frequency monitoring.
Monitoring a Nav Frequency
The Nav radio provides a monitor function for VORs in the Standby channel
similar to the Comm radio. The monitor function is activated or deactivated by
pressing the NAV button while in the Nav function.
The From radial for the Standby channel is
shown in parentheses when the VOR monitor mode is activated. This replaces
the station identifier, OBS course, or VOR/LOC indicator. The Standby VOR
radial is updated once per second. You cannot monitor a Localizer channel and
the Nav audio is temporarily disabled while the system is monitoring the
Standby VOR.
If no signal can be tracked on the Standby channel, then it will be dashed out.
The VOR Monitor function is turned off when you flip/flop frequencies, recall a
frequency, or press NAV again. Monitoring is not canceled by switching to Comm.
A small “m” will replace the
“s” in front of the Standby frequency.
The audio for the active Nav channel is toggled between modes using the ID
button. The annunciator above the button will light while the Nav audio is
activated, and the detected audio signal will be sent to the Nav audio output
circuit. Nav audio may also be mixed with the Comm audio output, if selected
in the System mode. This feature is used for installations that do not use an
external audio panel. When you are monitoring a VOR, Nav audio is suspended.
There are three modes for the Nav audio (Ident code, voice Ident, no Ident).
Press the ID button to start the ID mode. “IDENT” will be displayed for three
seconds. The Morse code tones sent over the VOR/Localizer channels will be
heard. If the ID button is pressed a second time. “VOICE” will be displayed for
three seconds. The Morse code tone volume will be reduced so you can hear
the voice transmission more clearly. Press ID again to turn the audio and ID
annunciator off.
The last audio output selection is kept in memory until you change it, even
when the SL30 is powered off. Using this feature, you may leave the audio
enabled and then control it by an external audio panel.
Listening to the Audio Channel
010º
Radial
0
9
27
18
3
6
12
15
21
24
33
30
030º
Radial
FAF
MAP
VOR ABC
116.00
XYZ ILS
111.10
111.10 m116.00 (010) bc +
}}
Graphic CDI
Fly right
Active Channel
ILS XYZ
Standby Channel
Monitors VOR ABC
Standby Channel
Radial
Display at the FAF
111.10 m116.00 (030) bc +
}
Display at the MAP
1. Press NAV to select the Nav receiver.
2. Set the Localizer frequency of your approach as the Active channel.
3. Press SEL. The display will prompt you to enable the Back Course.
Press ENT to enable the Back Course. Press SEL and ENT again to disable
the back course when it’s appropriate. When Back Course is enabled, it is
noted by “bc” on the display. You may also have a “bc” annunciation on the
external CDI.
4. Set the Standby channel to the appropriate VOR and note where a radial
crosses the FAF and MAP for your approach. Press NAV a second time to
“monitor” the Standby channel. A small “m” will replace the “s”.
5. The internal CDI (on the right side of the display) and the external CDI, if
installed, will guide you along the course to the runway.
6. The radial of the Standby channel you are monitoring will be shown in
parentheses to the right of the Standby channel.
7. Use the monitored Standby channel to note your location along the approach.
Example Back Course and Monitoring a Standby VOR
  • Page 1 1
  • Page 2 2

Garmin SL30 Reference guide

Garmin
Brand
Garmin
Model
SL30
Type
Reference guide
This manual is also suitable for

Garmin SL30 is a Comm Nav System that combines the functions of a Comm Radio, Nav Radio, and OBS into one compact unit.

The SL30 has a large outer knob that controls frequency selection in MHz and a small inner knob that controls frequency selection in kHz. The SL30 also has a number of buttons that control various functions, such as the mode select button, the enter button, and the squelch button.

The SL30 can store up to 20 user-defined frequencies, which can be recalled by pressing the SEL button and turning the large outer knob. The SL30 also has a number of pre-programmed frequencies, such as the emergency channel and the weather channel.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents