DUAL LITE DUAL-LITE LM33-03L 33W 6V High Capacity Emergency Light User manual

Brand: DUAL LITE

Model: DUAL-LITE LM33-03L 33W 6V High Capacity Emergency Light

Type: User manual

High-Capacity Emergency Lighting Units

Installation Instructions For Standard,

Remote Capacity And Damp

Location Models

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed including the following.

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

1. Do not use outdoors.

2. Do not mount near heaters or hot surfaces.

3. Equipment should be mounted in locations and at heights where it will not readily be subject to tampering by

unauthorized personnel.

4. The use of accessory equipment not authorized by the manufacturer may cause an unsafe condition.

Caution: Halogen cycle lamps may be used in this equipment. Halogen cycle lamps operate at high temperatures. Do not

  storeorplaceammablematerialsnearlamp.Toavoidshattering:Donotoperatelampinexcessofratedvoltage.Protect 

lamp against abrasion and scratches and against liquids when operating. Dispose of lamp with care.

5. Do not use this equipment for other than its intended purpose.

 6.Servicingofthisequipmentshouldbeperformedbyqualiedservicepersonnel.

SAVE THESE INSTRUCTIONS

WARNING – This product contains chemicals known to the State of California to cause cancer, birth defects and/or other

reproductiveharm.Thoroughlywashhandsafterinstalling,handling,cleaning,orotherwisetouchingthisproduct.

EMERGENCY LIGHTING AND POWER EQUIPMENT FOR USE IN DAMP LOCATIONS

Damp location listed units are suitable for use in:

1. Interior locations subject to moderate degrees of moisture, such as some basements, some barns, some cold-storage

warehouses, and the like.

 2.Partiallyprotectedlocationsundercanopies,marquees,roofedopenporchesandthelike.

GENERAL INSTRUCTIONS

This unit is designed for surface mounting on a wall or other sold surface (building support structure, column, etc.). Unit must be

mountedhighenoughtomaximizeilluminatedareaunderanticipatedconditionsofuse.Besuretoallowampleclearancefor

mounting and aiming the lighting heads.

Provideeachunitwithasingleunswitchedpowersupplyfroma120or277VACbranchcircuitusedfornormallightinginthesame

area. The wiring should be permanent installation, using appropriate size wire.

Note:De-energizeACcircuittounitduringinitialinstallation,andduringservicingorrelampingoperations.

PLACING THE UNIT IN SERVICE

 1. Loosenthetwocoverretainingscrewsonthesidesoftheunit,rotatetheheadsforclearance,andremovethecoverby 

lifting it up and outwards.

2. If lighting heads will be retained in the top mounted position, go to step 3. If lighting heads are to be relocated to side

mounted position, proceed as follows:

a. Snap out the lighting head knockouts on the sides of the unit.

b. Loosen the locking nut that retains the stem for each lighting head.

c. Slide each lighting head out of its present slot.

Note: It is not necessary to disconnect the lighting head leads from the circuit board.

d. Insert the stem of each lighting head into the side opening slots.

e. Tighten the locking nut on each stem so that the lamp heads turn with some resistance.

  f.Plugthetopmountedopeningslotswiththeholeplugscontainedinthehardwarepack.

 3. Fastenenclosuretoelectricaloutletboxand/orwallsurfaceusingappropriatehardware.

Note:Theenclosurecanbemountedto3˚”,4”octagon,or4”squareelectricalboxes,andtostandard

  plasterrings.Largeenclosureshaveadditionalkeyholeslotsforsurfacemounting.A7/8”diameter

  knockoutisprovidedonthetopandoneachsideoftheenclosureforsurfacewiringconduit.

Fig. 4 Double Harness Lead Connection

 LeadCalciumBatteries

6VoltTopView

6VoltPack

6VoltAnd12VoltPack(2Packs)

12VoltIndividual(2Batteries

Fig. 5 Single Harness Lead Connection

 Nickel-CadmiumBatteries

Fig. 6 Double Harness Lead Connection

 Nickel-CadmiumBatteries

6Volt(1Pack)SmallBattery

6Volt(2Pack)LargeBattery

6Volt(2Pack)SmallBattery

12Volt(4Pack)LargeOrSmallBatteries

Double Sided Tape

LM Series

currentlighting.com/dual-lite

without notice. All values are design or typical values when measured under laboratory conditions.

Rev 08/01/22

0603225_H_LM_Installation Instructions

0603225 H 8/21

•Units Supplied With Lead Calcium Batteries

 7. DetermineproperbatteryorientationfromFig.3(singleharnessleadconnection)orFig.4(doubleharnesslead  

  connection).Batteryispositionedtotheleftofthecircuitboard.Removeprotectivelinerfromdoublesidedtape,locatedon

  oorofenclosure.

Note:a1/4”space(minimum)isrequiredbetweenthefrontofthebatteryandtheinnerlipoftheenclosuretoprovide 

  clearanceforcover.Placebatteryintoenclosure,andpressdownrmlytosecurebatterytoenclosure.

 8. Connectpositive(+,red)andnegative(–,yellow)batteryharnessleadsfromprintedcircuitboardtocorrespondingbattery 

terminals as shown in Fig. 3 or Fig. 4.

9. Check all wiring for loose or missing connections.

10. Replacecover.Besurethateach“starwasher”isproperlypositionedbetweenthescrewheadandtheoutersurfaceofthe 

  cover.Tightenretainingscrews.Adjustlightingheadstodesiredposition.

11. EnergizeunitwithACpower.Pressandholdthe“TEST”button(seeFig.1for“TEST”buttonlocation)toconrm  

  illuminationandproperaimingofemergencylamps.(“ACON”indicatorLEDshouldgooff).Releasethe“TEST”button; 

  emergencylampsshouldextinguish.Normaloperationbegins.

12. NormalOperation:withpowersupplied,“ACON”LEDindicatorisilluminatedandemergencylampsareoff.

•Units Supplied With Nickel Cadmium Batteries

 7. DetermineproperbatteryorientationfromFig.5(singleharnessleadconnection)orFig.6(doubleharnesslead  

  connection).Batteryispositionedtotheleftofthecircuitboard.Removeprotectivelinerfromdoublesidedtape,locatedon

the battery.

Note:a1/4”space(minimum)isrequiredbetweenthefrontofthebatteryandtheinnerlipoftheenclosuretoprovide 

  clearanceforcover.Placebatteryintoenclosure,andpressdownrmlytosecurebatterytoenclosure.

8. Connect battery harness leads from printed circuit board to corresponding battery harness leads as shown in Fig. 5

or Fig. 6.

9. Check all wiring for loose or missing connections.

10. Replacecover.Besurethateach“starwasher”isproperlypositionedbetweenthescrewheadandtheoutersurfaceofthe 

  cover.Tightenretainingscrews.Adjustlightingheadstodesiredposition.

11. EnergizeunitwithACpower.

Note: allow unit to charge for 24 hours prior to testing.

  Pressandholdthe“TEST”button(seeFig.2for“TEST”buttonlocation)toconrmilluminationandproperaimingof 

  emergencylamps.(“ACON”indicatorLEDshouldbeoff).Releasethe“TEST”button;emergencylampsshouldextinguish.

Normal operation begins.

12. NormalOperation:withpowersupplied,“ACON”LEDindicatorisilluminatedandemergencylampsareoff.

ROUTINE TEST CYCLING

1. Monthly:Iftherehasbeennopowerfailure,pressandholdthe“TEST”buttonforatleastthirty(30)seconds   

  toconrmemergencylampoperation.Release“TEST”buttontoreturntobatterychargingmode.

2. Onceayear:Performafullbatteryconditioningcyclebyde-energizingtheACcircuittowhichtheunitisconnected,and 

  allowtheunittooperateforninety(90)minutesonbatterypower.Followingsuccessfultest,energizeACcircuittobegin 

battery charging cycle.

Note: ACONLEDblinkswhenbatteryisfullycharged.

REPLACING EMERGENCY LAMPS AND BATTERIES

General •Battery

1. De-energizetheACpowersupplytotheunit.    4. Removedefectivebattery.Recycleresponsibly.

2. Removeenclosurecover.       Replacewithgenuinemanufacturerbatteryonly.

3. Disconnectpositive(+,red)batterylead(nickel cadmium models- 5. Placenewbatteryinenclosure.Make  

disconnectbatteryandprintedcircuitboardconnectors).   connectionsfollowingstepsoutlinedabove.

6. Test unit.

•Emergency Lamp

Plastic Sealed Beam Type Heads Plastic Sealed Beam Heads Metal Heads

4. Gentlyprylamplens 4. Prytoremove 4. Gentlypryretainingring

 atarrowindicatormarks  outerring.  outofgrooveto

 toremovelens. 5. Replacelamp.  accesslamp.

5. Replacelamp.   5. Replacelamp.

Fig. 1 Pure-LeadOrLead-CalciumBattery

Fig. 2 Nickel-CadmiumBattery

Fig. 3 Single Harness Lead Connection

 Pure-LeadOrLead-CalciumBatteries

Cover

Retaining

Screw &

Star Washer

Ground

Wire

(Green)

Tape,

Double Sided

Transformer Ground

Wire (Green)

RemoteDCLamps

Positive(+)LeadWith

“On-Board”Fuse

RemoteDCLamps

Negative(–)Lead(s)

Transformer

120VAC–White&Black

277VAC–White&Red

Note: PotentialShock

Hazard–Insulate Unusead

Lead

Test Switch

“ACOn”LED

YellowNegative(–)

BatteryLead

RedPositive(+)

BatteryLead

RemoteDCLamps

Positive(+)Lead(s)

With“On-Board”Fuse

RemoteDCLamps

Positive(+)Lead(s)

With“Off-Board”Fuse

RemoteDCLamps

Negative(–)Lead(s)

Ground

Wire

(Green)

Cover

Retaining

Screw &

Star Washer

Transformer–“OffBoard”

(ModelLM15NHas“OnBoard”

Transformer

120VAC–White&Black

277VAC–White&Brown

Note: PotentialShockHazard

–Insulate Unusead Lead

BatteryLeads

& Connectors

Test Switch

“ACOn”LED

Plate

Ground

Wire

(Green)

RemoteDCLamps

Negative(–)Lead

(Yellow) RemoteDCLamps

Positive(+)Lead

“On-Board”Fuse

(Blue)

12VoltPack

TopView

12VoltPack

12VoltPure-LeadPack

12VoltSingle

6VoltSingle

Enclosure

CircuitBoard

Tape, Typical

6VoltSinglePure-Lead

4. Identify unit as using either:

•lead calcium batteries(standardmodels,i.e.LM30,LMP66)or

•nickel cadmium batteries(modelnumberendingwith“N”,i.eLM30N,LMP50N-12V)

 5. Connectremotelamps(ifused)toblue(+,fused)andyellow(–)leads(Fig.1orFig.2).

 6. Connect120or277VACinputconnectionstotransformer(Fig.1orFig.2).Connectgreenwiretobuildingground. 

Note:insulatetheunusedtransformerleadtopreventpotentialshockhazard.

Note: LM33l-03L with Spectron must use its internal lamp load (6W) in addition to a remote lamp load between 6W and

15W to obtain lamp sensitivity adjustment

DUAL LITE DUAL-LITE LM33-03L 33W 6V High Capacity Emergency Light User manual

Brand: DUAL LITE

Model: DUAL-LITE LM33-03L 33W 6V High Capacity Emergency Light

Type: User manual

Download PDF

report

DUAL LITE DUAL-LITE LM33-03L 33W 6V High Capacity Emergency Light User manual

DUAL LITE DUAL-LITE LM33-03L 33W 6V High Capacity Emergency Light User manual

Related papers

Other documents