Sim2 M.120/M.120ST User manual

Brand: Sim2

Model: M.120/M.120ST

Category: Data projectors

Type: User manual

This manual is also suitable for

SIM2 Multimedia

M.120

User Guide

Contents

3 Important information

About this User Guide

Safety

3D Content

Environment

Notice

7 Chapter 1: Introduction

Key Features and Benefits

System Components

Optional Accessories

9 Chapter 2: Overview

Remote Control

Projector Keypad

Connections

3D RF Emitter

3D Glasses

14 Chapter 3: Installation

Location

Mounting

Connections

Switching On and Off

19 Chapter 4: Operation

Viewing 3D Content

3D Menu

Input Menu

Main Menu

Picture

Image

Setup

Memories

Info

Quick Menus

Messages

35 Chapter 5: Troubleshooting

37 Chapter 6: Specifications

39 Chapter 7: Projection Distances

40 Chapter 8: Dimensions

M.120

User Guide

Important information

About this User Guide

This User Guide describes how to set up and operate the M.120 LED 3D projector.

Information contained in this User Guide may be updated from time to time due to

product improvements and customer feedback. Visit www.sim2.com to find the latest

version of this document.

This document contains proprietary information protected by copyright. All rights are

reserved.

All trademarks and registered trademarks are the property of their respective owners.

Safety

To reduce the risk of electrocution, disconnect the power cord on the

rear panel before removing the top cover of the projector. For technical

service refer to trained personnel authorized by the manufacturer.

Read this guide

Read all chapters of this guide carefully before switching on the projector. This guide

provides basic instructions for operating the M.120 projector. Installation, preliminary

adjustments and procedures that necessitate the removal of the top cover and

contact with electrical components must be performed by authorized, trained

technicians. To ensure safe operation and long term reliability use only the power

cords supplied by the manufacturer. Observe all warnings and precautions. Keep this

guide for future consultation.

Do not touch internal parts of the projector

Inside the housing there are electrical parts carrying dangerously high voltages and

parts operating at high temperature. Never open the housing. Entrust all servicing and

repair work to a SIM2 Authorized Service Center. Opening the housing voids the

warranty.

Disconnect the appliance from the power supply

The device that disconnects the projector from the mains is the power plug. Ensure

that the power cord plugs and the electrical outlets are easily accessible during

installation operations. Pull the plug, not the cord, to disconnect the projector from

the mains. Use only the specified power supply. Connect the projector to a mains

electrical supply with rated voltage of between 100-240 V AC, 50/60 Hz and equipped

with a protective earth connection. If you are not sure of your domestic mains rating,

contact an electrician. Take care to avoid overloading the power socket and any

extension leads.

Changing the fuses

Before changing the fuse, disconnect the projector from the mains power supply. The

fuse compartment is next to the power supply connector. Remove the fuse holder

Important information M.120

User Guide

with a flat head screwdriver and replace the fuse. Fit the replacement fuse. Use only

type T 10 A L H fuses for the projector.

Be careful with cables

Make sure cables are routed so that people are not impeded or become a trip hazard.

Keep all cables away from children. Install the projector as close to the wall socket as

possible. Avoid stepping on power cords, make certain they do not become tangled,

and never jerk or tug them; do not expose them to sources of heat, and make sure

they do not become knotted or crimped. If the power cords become damaged, stop

using the projector and request the assistance of an authorized technician.

Disconnect the projector from the mains power during electrical storms and when

not in use

To prevent damage from lightning strikes in the vicinity, disconnect the projector

during storms or when the projector is going to be left unused for a long time.

Avoid contact with liquids and exposure to damp

Do not use the projector near water (sinks, tubs and so on); do not place objects

containing liquids on or near the projector and do not expose it to rain, humidity,

drops of water or sprays; do not use water or liquid detergent to clean it.

Place the projector on a stable surface

Place the projector on a stable surface or use a suitable ceiling mounting bracket.

Never place the projector on its side or rear, on the lens or top panel.

Do not allow the projector to overheat

To prevent overheating, allow a free space of at least 0.25 m (10 in.) on the left, right

and rear sides of the projector. Do not obstruct the ventilation slots. Do not place the

projector near heat sources such as heaters, radiators or other devices (including

amplifiers) that generate heat. Do not place the projector in an area where there is

insufficient space (shelving units, bookshelves and so on) and in general avoid placing

it in poorly ventilated areas as this may prevent sufficient cooling.

Never look directly into the projection lens

Never look directly into the lens when the projector is on as the intense light may

damage your eyes. Take particular care that children cannot do so.

LED LIGHT

DO NOT STARE INTO BEAM

CLASS 2 LED PRODUCT

P ≤ 0.88 mW λ = 452 nm

ICE 60825-1:1993 + A1:1997 + A2:2001

EN 60825-1:1994 + A2:2001 + A1:2002

Take special care regarding movement of the lens

Do not place objects in the slots on the side of the lens and also ensure that vertical

lens movements are not impeded by external objects.

Important information M.120

User Guide

Do not insert objects through the openings in the projector

Make sure that no objects are inserted inside the projector. If this should occur,

disconnect the projector from the power supply immediately and call an authorized

technician.

Power saving

We advise disconnecting the projector from the power supply when not in use. In this

way you will achieve considerable power savings while at the same time protecting

internal electrical parts from wear.

3D Content

Discomfort (such as eye strain, headaches, motion sickness, nausea, dizziness, disori-

entation) may be experienced while watching 3D content. In this case, stop watching

and consult a doctor if symptoms are severe.

Consult a doctor before allowing young children (especially those under six years old)

to watch 3D content as their visual system is still under development.

Monitor children (including teenagers) watching 3D content, as they are more at risk

of experiencing discomfort and less inclined to report symptoms.

Individuals who may be susceptible to epileptic seizures or strokes (on the basis of

personal and family history) should consult a doctor before watching 3D content.

All viewers should take regular breaks from watching 3D content. Length and

frequency of these breaks may vary from person to person.

Environment

This product contains materials derived from natural resources during its

manufacture. It may contain materials that constitute a health and environmental

hazard. To prevent harmful materials from being released into the environment and to

promote the use of natural materials, SIM2 provides the following information

regarding the disposal and recycling of the product.

Waste electrical and electronic materials (WEEE) should never be disposed of in

normal urban waste disposal facilities.

The label on the product, shown here, indicating a canceled garbage can,

is intended to remind you that the product requires special handling at

the end of its service life. Materials such as glass, plastic and some

chemical compounds are recoverable and can be recycled for reuse.

Observe the following instructions:

• When you no longer wish to use your electrical and electronic equipment,

take it to your local waste disposal facility for recycling.

• You may return your old equipment to your SIM2 Authorized Dealer free of

charge when you buy a new product that is equivalent or has the same

functions as the old one. Contact SIM2 to find your local dealer.

• If you need more information regarding recycling, reuse and product

exchanges, contact SIM2 customer service.

Important information M.120

User Guide

Lastly we suggest further measures to safeguard the environment, such as recycling of

internal and external packaging (including that used for shipping) in which the product

was delivered. With your help, we can reduce the amount of environmental resources

required to make electric and electronic equipment, reduce the use of waste tips for

used equipment and, in general, improve our quality of life by making sure that

hazardous materials are correctly scrapped. Incorrect treatment of the product at the

end of its service life and failure to follow the above disposal instructions are

punishable under local legislation.

Notice

The appliance has been subjected to exhaustive operating tests by SIM2 to guarantee

the highest quality. The projector light source life should thus initially be around 30-60

hours. In addition to the customary checks, the Quality Control department also runs

additional statistical tests before shipment. In such cases, the packaging may show

signs of having been opened, and the hours of light source operation may prove to be

higher than those normally shown when only standard tests are performed.

As the optical system of the M.120 is extremely compact and has the purpose of

developing very high brightness and contrast, it is possible that a small quantity of

light is visible outside of the projection area and will vary depending on the type of

lens used and the zoom and shift setup. This characteristic of the optical system is to

be deemed as normal. In order to reduce this effect SIM2 recommends that the area

surrounding the projection screen is as dark as possible.

Important information M.120

User Guide

1 Introduction

The M.120 is a high-end compact 3D single unit projector that incorporates PureLED

technology, a combination of single chip DLP from Texas Instruments, three individual

high power LEDs, a new light engine, and a dedicated video processing.

PureLED technology allows the projector to deliver clearer, brighter and more vibrant

images, a wider and more consistent color gamut, and full-on/full-off contrast up to

100,000:1.

The M.120 is able to emulate the best 3D cinema projection systems, in terms of color

fidelity, definition and depth of image. These are all conveyed accurately, as is the fluid

motion of fast-action movies and sports. This all adds up to an incredible 3D

experience at home.

The M.120 is designed for use with large screen sizes – up to 4 m (14 ft.) wide. A

choice of two high quality glass lenses (T1 and T2) is available, giving the projectors a

total throw ratio of 1.5-3.9:1.

To aid calibration SIM2’s Live Color Calibration software enables complete control

over:

• primary, secondary and white point color coordinates

• gamma tables

allowing calibration experts to accurately calibrate the final image via a user-friendly

application for Windows-based computers.

Key Features and Benefits

• high picture quality: SIM2 renown image processing and the latest 0.95 in.

1080p DMD from Texas Instruments

1 Introduction M.120

User Guide

• precision optics: compact die-cast light engine with precision glass optics and

motorized zoom, focus and lens shift

• longer light source life: typical life estimated around 30,000 hours

• richer and more saturated colors: wider and more consistent color gamut and

full-on/full-off contrast up to 100,000:1

• extremely quiet level of operating noise: liquid-cooling system

• quick on/off: warm-up and cool-down periods require seconds not minutes

• artifact-free fast-action images: SIM2 PureMotion processing

• high resolution: actual full HD 3D images, without blur and ghosting

• comfortable 3D viewing: high brightness ghost-free sharp images

• immersive 3D effect: large screen sizes thanks to high brightness images

• 3D wide viewing angle: stereo separation independent from viewing angles

• screen flexibility: no constraints in the choice of the screen material

• compatibility: no need of dedicated sources and preprocessing for 3D viewing

System Components

Your M.120 DLP projector ships with the following items:

• 1 x backlit remote control unit (with four AAA/LR03 batteries)

• 3 x AC power cords (US, EU and UK), 2 m (6.6 ft.) long

• 3 x jacks for 12 V output connectors

• 1 x User guide (this document)

If any items are missing or damaged, contact your SIM2 Authorized Dealer as soon as

possible. Keep the original packaging in case anything has to be shipped.

Optional Accessories

• VISUSRF-BOX (8 SIM2 Visus 3D RF glasses)

• VISUSRF-SYSTEM (7 SIM2 Visus 3D RF glasses and 1 RF emitter for SIM2 Visus

3D RF glasses)

• VISUSRF-SYSTEM-ACC (4 SIM2 Visus 3D RF glasses and 1 RF emitter for SIM2

Visus 3D RF glasses)

• Projector ceiling bracket

• Anamorphic lens systems (fixed or motorized)

1 Introduction M.120

User Guide

2 Overview

❶

Projection Lens Available in two versions: T1 (1.5:1 to 2.1:1) and T2 (2.1:1 to 3.9:1)

❷

Front IR Sensor Receives infrared signals from the remote control unit

❸❹

Ventilation slots Ensure reliable operation and protect the projector from

overheating. Make sure they are not obstructed.

❺

Indicator light and

status display

Show projector status as follows:

Indicator light:

• solid red = low power standby

• solid orange = fast switch on standby

• flashing green and red = initialization or cooling down

• solid green = normal operation

Status display:

• 88 = initialization

• black = normal operation

• two-digit code = error status (displayed code may be useful

for troubleshooting)

❻

Rear IR Sensor Receives infrared signals from the remote control unit

❼

Keypad Controls the main functions of the projector. Pull the cover to access

the keys. See “Projector Keypad” on page 11 for a detailed

description of their functions.

❽

AC receptacle and

main power switch

Plug here the female end of the AC power cord that is appropriate in

your area. Switches the projector on or off.

❾

Connector Panel Contains the connections for all input, control and output signals.

See “Connections” on page 12 for details

2 Overview M.120

User Guide

Remote Control

Turn backlight on for about 5 seconds

Turns the projector off

1-9

Select inputs and turn the projector

Enters OSD Input menu and turns the

projector on

● OK enters submenus, confirms actions

ESC Exits OSD

▴

◂ ▸

▾

Select menu items, adjust settings or

cycle through the test patterns

+ / -

Enter OSD Main menu and select the

desired section, each press of the key

selects the next tab in the menu

II 3D enters 3D menu

Memory enters Memories menu

F1, F2

Perform user-defined actions (default

assignments are: F1 = Zoom, F2 =

Focus)

Info displays projector Info

A Auto performs Auto Adjustment

Aspect enters Aspect Quick menu

Not used

Custom Remotes

You can use your own IR remote control to control your M.120 projector.

• If you are using a remote control with learning capabilities, use the projector

remote control to teach the commands to your remote.

• If you are using a programmable remote control, the setup software probably

allows importing of Pronto Hex codes. See SIM2 M.120 IR Control for a list of

all the projector codes in Pronto Hex format, including a number of discrete

codes for:

◦ Aspects

◦ Memories

◦ 3D Controls (3D Mode and Input Formats)

Operation

The M.120 projector has two IR receivers, one on the front and one on the back of the

unit. The operative range of the remote control is approximately 10 m (33 ft.). Make

2 Overview M.120

User Guide

sure that there is nothing obstructing the infrared beam between the remote control

and the IR receiver you are pointing to. You can point the remote control towards the

screen, as the IR beam is reflected by the screen towards front IR receiver of the

projector. In this case the effective range of the remote control may be smaller than

declared.

Note: In some cases when using 3D the accuracy and responsiveness of the remote

control will be reduced.

Batteries

To install batteries in the remote control:

1. Open the battery cover.

2. Insert four AAA (LR03) batteries making sure the polarities match the + marks

inside the battery compartment.

3. Replace the cover.

Replace the batteries with new ones when the operating range of the remote control

decreases. Dispose of used batteries according to local regulations. Make sure you do

not mix old and new batteries or different types of batteries.

Warning: If you will not use the remote control for a long time, remove the batteries

to avoid battery leakage.

Projector Keypad

turns the projector on or off

◂ ▸ ▴ ▾

select menu items, adjust settings or switch test patterns

MENU enters OSD Main menu and selects the desired section

ESC exits OSD

SOURCE/O enters OSD Input menu/selects a menu item

2 Overview M.120

User Guide

Connections

❶ ❷ ❸ ❹ ❺ ❻

❼ ❽

Inputs

❶

HDMI 1

HDMI 2

Accept both HDMI and DVI digital video inputs.

❷

Components/RGB-HV Four RCA connectors. They accept both standard

and high-definition component (YPrPb) and

RGB-HV signals. Also used as RGB input for SCART

RGBS signals.

❸

Video One RCA connector. Accepts composite video

signals. Also used as composite sync input for

SCART RGBS signals.

❹

Graphics RGB One D-Sub 15-pin female connector. Accepts

component or RGB high-definition signals.

Control/

Service

❺

USB USB 1.1 (type B) port for serial commands and

firmware upgrade.

❻

RS-232 RS232 (female D-Sub 9-pin) port for serial

commands and firmware upgrade.

Outputs

❼

TRIG 1 12 V 100 mA max output, for motorized screen

control. Activates when the projector is switched

on.

TRIG 2 12 V 100 mA max output, for motorized screen

masking systems control. See “Screen” on page

28.

TRIG 3 12 V 100 mA max output, for motorized

anamorphic lens position control. See

“Anamorphic Lens” on page 28.

❽

3D Sync OUT VESA DIN-3 connector for 3D RF Emitter cable.

2 Overview M.120

User Guide

3D RF Emitter

The 3D RF emitter is designed to be placed near the projector and aimed at the

screen. It receives the 3D sync signal from the projector and emits RF pulses that

reach the 3D glasses RF receiver.

The emitter does not require a battery.

Note: The emitter emits sync pulses only when the projector displays 3D content.

3D Glasses

When displaying 3D content, the projector alternately displays one image for the left

eye and one image for the right eye in rapid succession. The 3D glasses turn on and off

their lenses, in sync with the projector, so that each eye receives exactly the image

intended for it. The sync is possible thanks to the RF pulses received by the glasses

from the 3D RF emitter.

❶ Button Button for ON and OFF

❷ LED Indicating glasses status

❸ Micro USB port To charge the glasses

❹

Lens Liquid crystal shutter

❺ RF Receiver Receive RF signals from 3D Emitter

2 Overview M.120

User Guide

3 Installation

This section provides instructions for the installation of the M.120 projector.

Important: Installation procedures should be performed by a qualified AV system

specialist.

Location

When installing the M.120 projector, take the following considerations into account.

Installation Type

Select the installation type that best suits your needs:

• front or rear projection

• floor or ceiling mount

Lens Type

Choose the desired distance from the screen and select the lens type (T1 or T2) that

determines the desired screen size.

Cooling

Make sure that the planned location for the projector has adequate ventilation. Check

that room temperature is below 35° C and that the projector is away from heating

vents. Ensure a minimum 0.25 m (10 in.) clearance on the left, right and rear sides of

the projector.

Power Outlets

Verify that the powers outlets are grounded and preferably shielded from power

surges and fluctuations. A UPS is optional. M.120 power supply operates on any

nominal line voltage between 100-240 V AC, 50-60 Hz.

Cables

Check planned cable lengths for video and control cables and make sure these lengths

do not exceed specifications.

Ambient Light

Avoid or minimize light sources directed at the screen to preserve the quality of the

projected image.

Mounting

The projector can be Floor mounted (upright) or Ceiling mounted (inverted). Choose

the method that best suits your installation.

Important: The projection lens is centered to the chassis, see “Dimensions” on page

41 for details). Make sure the centerline of the lens is centered horizontally to the

center of the screen.

Floor Mounting

Position the projector on a secure and flat surface (such as a table or a shelf). Adjust

the four feet at the bottom of the projector until the projector is level on all sides.

3 Installation M.120

User Guide

Ceiling Mounting

Invert the projector and suspend it from the ceiling using a specific bracket.

• To fit the bracket unscrew and remove the four rubber feet

• Attach bracket by using six M6 screws not exceeding 8 mm in length

For ceiling mounting use only SIM2-approved ceiling brackets and adhere

to the installation instructions and safety guidelines provided with the

bracket. Do not over-tighten the screws.

Orientation

By default, the M.120 is configured for a Front installation (projector installed upright

and in front of the screen). If the projector is installed behind the screen or inverted,

you can use the image orientation function of the projector (see “Orientation” on

page 30)

Lens Shift

Ideally, the projector should be positioned perpendicular to the screen and in such a

way that:

• the lens center and screen center are aligned with each other

• the projected image fills the screen perfectly.

If it is not possible to position the projector perpendicular to the projection screen

you can use the motorized lens shift controls to shift the projected image vertically

and horizontally. Table 3.1 provides usable lens shift ranges for floor installations

(projector upright) and ceiling installations (projector inverted). Vertical and horizontal

shift limits are expressed as percentages of the image height and of the image width

respectively.

Important: The amount of vertical shift available can be limited if horizontal shift has

also been applied.

Table 3.1

Direction Sense Floor Mounting Ceiling Mounting

Vertical Up 60% 25%

Down 25% 60%

Horizontal Left 7.5% 7.5%

Right 7.5% 7.5%

Note:

Percentages refer to image height or width respectively. Tolerance is ±2.5%

Note: You can access the Lens Shift adjustment through the remote control directly,

using F1 key or F2 key. See “F1-F2 Keys” on page 32 for details.

Keystone

If the projector is ceiling-mounted and the screen is lower than the projector, you may

need to tilt the projector by adjusting the ceiling mount. If you do so:

• the top and bottom borders of the image will be unequal in length

• the sides of the image will be inclined

If the tilt is not excessive, you can use the Keystone function of the projector to

correct the image shape. See “Keystone” on page 30.

3 Installation M.120

User Guide

Note: Keystone correction may cause artifacts in the image and may not be available

when displaying specific 3D content (see Table 4.2).

Zoom and Focus

The M.120 provides motorized Zoom and Focus controls. You can access these

adjustments through the remote control directly:

• F1 key for optical Zoom

• F2 key for Focus

See “F1-F2 Keys” on page 32 for details.

Connections

Proceed as follows to connect the M.120 to video sources, control devices, screen

control systems, 3D sync emitter and AC power.

When connecting your equipment:

• turn off all equipment before making any connections

• use the correct signal cables for each source

• make sure cables are routed so that people are not impeded or become a trip

hazard

• ensure that the cables are securely connected (tighten the thumbscrews on

connectors that have them)

Video

Often the sources (Blu-ray Players, Set Top Boxes, Game Consoles and so on) have

several outputs. Choose HDMI whenever possible.

• HDMI The major benefits of this signal type are:

◦ best image quality, because the signal is carried in the digital domain

throughout the entire signal path

◦ highest available resolution, because video sources can deliver full

resolution content via HDMI only

◦ availability of 3D content, because most 3D compatible sources deliver 3D

content from HDMI only

◦ optimization of several image parameters (2D/3D content, color space,

aspect, signal range, over scan), thanks to auxiliary information (AVI

infoframe) sent by the source device together with the signal.

If your source has dual HDMI outputs, we would recommend direct

connection to the projector from one of the HDMI connections and the

second HDMI output to the input of an appropriate AV receiver/processor for

audio.

Sources with a DVI-D output can be connected to the HDMI input of the

projector using a suitable DVI-D to HDMI cable. In this case no auxiliary

information is sent from the source to the projector.

Note: HDMI uses a code known as HDCP (High-bandwidth Digital Copy

Protection), which protects the recorded supports from being copied illegally.

The connection between the source and display require that the two devices

perform a handshake and exchange code keys before being able to display an

image. The InstaPort technology allows a simultaneous pre-authentification of

3 Installation M.120

User Guide

every attached device at the same it is connected, reducing drastically the

time required for HDMI source switching. For this reason you may note a

slight delay before the image appears on the screen, but it is perfectly normal.

• Graphics RGB Input for Personal Computer and other sources that outputs

RGB or YPrPb signals. These sources must be able to provide separate H/V

sync or composite H+V sync.

• RGB/YPrPb Input for DVD Players, Set Top Boxes and other sources that

output one of the following signals:

◦ Component (YPrPb)

◦ RGB with composite sync on green (RGsB)

◦ RGB with HV composite sync

RGB connectors also provides RGB input for SCART RGBS sources. See “Video”

below and “RGBS Sync” on page 30.

• Video This is the the input for composite video sources (such as VCR or

camcorders). This connector is also the composite sync input for SCART RGBS

sources. See “RGB/YPrPb” above and “RGBS Sync” on page 30.

Control

You can connect the M.120 projector to a Personal Computer or a control system

through one of the following methods:

• RS-232 port, using a standard 9-pin straight serial cable

• RS-232 port, using a USB to serial converter cable. In this case, installation of a

device driver provided by the cable manufacturer may be required

• USB port, using a USB Type A (rectangular) to Type B (square) cable connector.

In this case, installation of a device driver provided by SIM2 may be required –

ask your SIM2 Authorized Dealer

Note: RS-232 communications are limited to 15 m (50 ft.), whereas USB are limited to

5 m (16 ft.).

Triggers

Some Home Theater devices can be controlled through a 12 V signal. The projector

can output three 12 V (100 mA max) signals:

• TRIG1 for motorized screens control

• TRIG2 and TRIG3 are for motorized screen masks and anamorphic lens motors

control. See “Screen” and “Anamorphic Lens” on page 28 for instructions on

how to do configure them from OSD

Note: Three jack adapters are shipped with the projector.

3D RF Emitter

The RF emitter sends the RF pulses that sync the 3D glasses. Proceed as follows to

install the emitter:

1.Place the emitter near the projector on a secure surface or use an appropriate

mount kit. For maximum range emitter should not be placed on the ground/floor but

should be placed at least 10 cm above ground (like on a shelf).

2.Connect the emitter connector to the corresponding 3D Sync Out output connector

in the projector.

3 Installation M.120

User Guide

3.Once the emitter is connected to the projector, please make sure that the projector

is in 3D mode. Check the X sign on the emitter; the red light should be on, indicating

that the emitter is functioning.

3D Glasses

Proximity Association with 3D RF emitter

The following procedure has to be done every time the glasses are introduced to new

3D RF emitter. During the proximity association, 3D glasses shall be located within 1 m

from 3D RF emitter.

Switch on the glasses (1 short press on the button). LED will change from off to bright,

indicating glasses power on.

Press button for minimum of 1 second.

After 1 second, LED will start to blink with a rate of 1 blink per 2 second.

Release the button.

Successful proximity association is indicated with 6 short LED blinks.

If glasses could not proximity associate LED will change from bright to off and

glasses will go in power off state.

Connecting glasses to 3D RF emitter

Once glasses are associated with the emitter, they will automatically connect to that

emitter every time they are switched on. If during the operation glasses lost the

connection to the emitter, they will automatically try to reconnect to that emitter (LED

is blinking with a rate of 1 blink per 2 seconds). If glasses cannot successfully

reconnect to the emitter within 60 seconds, LED will change from bright to off and

glasses will automatically go in power off state.

Indicating the battery state

If LED flashes every couple of seconds during the operation, battery level is low.

Charging is indicated with lit LED.

Charging the battery

The glasses are shipped with the micro USB to USB Type A cable. To charge the glasses

battery, plug the micro USB cable in a computer or other USB device capable of

supplying power. LED will remain lit while glasses are charging. When battery is fully

charged LED will go off.

For more information on glasses status and transitions, refer to “3D Glasses” on page

21.

Distances from glasses to 3D RF Emitter

The minimun distance from glasses to 3D RF Emitter is 10 m, the maximun depends

on how the room is made.

AC Power

Choose the AC power cord that is appropriate in your area among those shipped with

the product. Plug the female end of the power cord to the AC receptacle located on

the rear of the projector (100-240 V AC, 50-60 Hz) and the other end into a grounded

AC outlet. An high-quality surge protector is recommended while a UPS is optional.

3 Installation M.120

User Guide

Switching On and Off

Switching On

1. Turn on the main power switch on the rear of the projector. The projector

enters the low power Standby status. The indicator light on the left hand side

of the projector turns red and the status display next to it shows . .

2. Press any of the numeric keys (0-9) on the remote control or the I/O button

on the projector keypad to switch on the projector.

3. The indicator light turns green and red and the status display shows 88 for a

while.

4. The SIM2 logo appears on the screen within five seconds.

5. When the projector is ready for use (this can take approximately 40 seconds),

if a valid signal is detected, an image appears on the screen (otherwise a black

screen with the “No Signal” message is displayed).

Switching Off

1. Press and hold the Off key on the remote control or the I/O button on the

projector keypad.

The indicator light flashes green and red to indicate that the projector is

cooling down. Cooling fans remain on for approximately ten seconds to cool

the light source. In the meanwhile the projector cannot be turned on again.

2. After cooling is complete the projector enters Standby status. The status

display turns black, unless an error or warning code is displayed.

3. The indicator light turns:

• Red if Standby Mode is set to Eco

• Orange if Standby Mode is set to Fast Switch On

3 Installation M.120

User Guide

4 Operation

Viewing 3D Content

3D stereo visualization offers clear and sharp 3D images thanks to single chip DLP

Imaging technology. This technique achieves channel separation using active shutter

glasses.

• Active shutter glasses turn on and off in rapid succession and stop light

reaching your eyes. The glasses are synced using a RF emitter connected to

the projector.

• When an image is destined for the left eye, the right lens of the glasses goes

dark preventing any of the image for your left eye from reaching the right eye.

The left lens is completely open.

• The process repeats very quickly (up to 120 times per second) for each eye.

• The human brain combines the two images and creates the illusion of 3D.

Important: Read 3D safety information at the beginning of this User Guide before

viewing 3D content.

Your M.120 projector is capable of displaying 3D Images of exceptional high quality; to

ensure maximum enjoyment and trouble free viewing we recommend the following

guidelines.

• You will need a Blu-ray player or equivalent that is capable of

playing 3D content and is HDMI compliant plus of course a copy of

a film that has released on Blu-ray in 3D. Only films with the 3D logo are

compatible.

• Ensure your player has the latest software installed.

• If your Blu-ray Player has dual HDMI outputs, we would recommend direct

connection to the projector from one of the HDMI connections and the

second HDMI output to the input of an appropriate AV receiver/processor for

audio.

• If you are routing all of your HDMI sources through an AV receiver/processor

the product must be 3D compatible and HDMI compliant. Ensure your

equipment has the latest firmware installed (refer to the manufacturer for

further information).

• Other 3D content providers are available such as Satellite Broadcasters, Cable

providers, VOD and Streaming services, gaming consoles such as PlayStation 3.

Details of the 3D service provided can be obtained by contacting your

local/regional operators.

To watch 3D Content via Blu-ray

• Switch on the M.120 and all other relevant products such as Blu-ray player

and AV receiver and ensure the correct inputs have been selected.

• Insert your 3D Blu-ray disc and press play, follow the on-screen menus.

Note: Some discs contain both the 3D and 2D versions of the film, ensure you

4 Operation M.120

User Guide

Page is loading ...

Sim2 M.120/M.120ST User manual

Brand: Sim2

Model: M.120/M.120ST

Category: Data projectors

Type: User manual

This manual is also suitable for

Download PDF

report

Sim2 M.120/M.120ST User manual

This manual is also suitable for

Sim2 M.120/M.120ST User manual

Related papers

Other documents