Telular Cell Phone 850, 1800, 1900 User manual

Brand: Telular

Model: Cell Phone 850, 1800, 1900

Category: Telephones

Type: User manual

This manual is also suitable for

12/15/04 Part Number 56031701

PHONECELL

SX6P GSM

• Fixed Wireless Phone

850/1800/1900 MHZ GSM (TRI BAND) AND

900/1800/1900 MHZ GSM (TRI BAND) MODELS

USER MANUAL

Phonecell

SX6P GSM i User Manual

Fixed Wireless Phone

Serial Cable

or USB Cable

(SX6P-300G

series only)

This manual is for use with all SX6P-200G and SX6P-300G series deskphones

only. To determine which model of phone you have, pick up the phone and view

the label underneath for verification.

Phonecell

SX6P GSM ii User Manual

SX6P MENU STRUCTURE

Phonebook

Service Numbers

View Names

Add Name

Settings

Messages

Received Messages

Saved Messages

Create Message

Message Settings

Voicemail

Info Message

Clock

Set Alarm

Clock Settings

Set Time

Set Date

Set Time Zone

Settings

Phone Settings

Audio Settings

Call Settings

Data Settings*

Dial Settings

Network Settings

Security Settings

Restore Defaults

Service Settings**

Call Log

All Calls

Missed Calls

Received Calls

Dialed Numbers

Clear Logs

Call Time

GPRS Info

Call Divert

All Calls

When Busy

No Answer

Not Found

Cancel All Diverts

* Not available on SX6P-200G

** Requires password

Phonecell

SX6P GSM iii User Manual

Before installing your Phonecell

SX6P, carefully remove the contents from the shipping carton

and check for evidence of shipping damage. If damage is found, contact your Authorized

Telular Distributor or shipping agent immediately.

SAFE OPERATION INSTRUCTIONS

IMPORTANT! Before installing or operating this product, read the SAFETY INFORMATION

section of this manual.

••

Install unit indoors.

••

Install unit on hard, flat surface for proper ventilation.

••

Do not expose unit to rain or moisture.

••

Do not place unit on or close to sources of heat

IMPORTANT NOTICES

TERMS AND CONDITIONS FOR USE OF PHONECELL

PRODUCTS ("Product")

These Terms and Conditions are a legal contract between you and Telular Corporation for the title to and use of the Product.

BY RETAINING AND USING THE PRODUCT AFTER RECEIPT OF IT, YOU AGREE TO THE TERMS AND CONDITIONS

INCLUDING WARRANTY DISCLAIMERS, LIMITATIONS OF LIABILITY AND INDEMNIFICATION PROVISIONS BELOW. IF

YOU DO NOT AGREE TO THE TERMS AND CONDITIONS, DO NOT USE THE PRODUCT AND IMMEDIATELY RETURN

THE UNUSED PRODUCT FOR A COMPLETE REFUND. You agree to accept sole responsibility for any misuse of the Product

by you; and, in addition, any negligent or illegal act or omission of your or your agents, contractors, servants, employees, or

other users of the Product so long as the Product was obtained from you, in the use and operation of the Product.

INDEMNIFICATION OF TELULAR CORPORATION ("TELULAR")

YOU SHALL INDEMNIFY, DEFEND AND HOLD HARMLESS TELULAR FOR ANY OF THE COST, INCLUDING REASON-

ABLE ATTORNEYS' FEES, AND FROM CLAIMS ARISING OUT OF YOU, YOUR CLIENTS' OR OTHER THIRD PARTIES'

USE OR OPERATION OF THE PRODUCT: (i) FOR MISUSE OR IN A MANNER NOT CONTEMPLATED BY YOU AND

TELULAR OR INCONSISTENT WITH THE PROVISIONS OF THIS MANUAL; (ii) IN AN ILLEGAL MANNER OR AGAINST

PUBLIC POLICY; (iii) IN A MANNER SPECIFICALLY UNAUTHORIZED IN THIS MANUAL; (iv) IN A MANNER HARMFUL

OR DANGEROUS TO THIRD PARTIES; (v) FROM CLAIMS BY ANYONE RESPECTING PROBLEMS, ERRORS OR MIS-

TAKES OF THE PRODUCT; OR (vi) COMBINATION OF THE PRODUCT WITH MATERIAL, MODIFICATION OF THE

PRODUCT OR USE OF THE PRODUCT IN AN ENVIRONMENT NOT PROVIDED, OR PERMITTED, BY TELULAR IN WRIT-

ING. THE PARTIES SHALL GIVE EACH OTHER PROMPT NOTICE OF ANY SUCH COST OR CLAIMS AND COOPER-

ATE, EACH WITH THE OTHER, TO EFFECTUATE THIS INDEMNIFICATION, DEFENSE AND HOLD HARMLESS.

TELULAR CORPORATION

Corporate Headquarters

647 North Lakeview Parkway

Vernon Hills, Illinois 60061, USA

Technical Support

Tel: 847-247-9400 • Fax: 847-247-0021

E-mail: support@telular.com • http://www.telular.com

Power Supply

Phonecell

SX6P GSM Desktop Phone

Spike Antenna

PLEASE SEE THE IMPORTANT NOTICES SECTION OF THIS MANUAL FOR

IMPORTANT INFORMATION ON USE, WARRANTY AND INDEMNIFICATION

CONTENTS

AC Power Cord

Phonecell

SX6P GSM iv User Manual

TABLE OF CONTENTS

QUICK CONNECTION GUIDE .......................................................................................i

SX6P MENU STRUCTURE............................................................................................ii

CONTENTS ...................................................................................................................iii

SAFE OPERATION INSTRUCTIONS...........................................................................iii

IMPORTANT NOTICES.................................................................................................iii

SX6P SETUP..................................................................................................................1

SIM Card Installation .................................................................................................1

Battery Installation .....................................................................................................1

Battery Operation.......................................................................................................2

Location and Setup....................................................................................................2

Connect the Handset .................................................................................................2

Wall-Mounting ............................................................................................................3

Connect the SX6P to AC Power ................................................................................4

GETTING TO KNOW YOUR SX6P................................................................................5

Function Keys ............................................................................................................5

LCD Screen Icons......................................................................................................6

Service Indication ......................................................................................................6

CALL FUNCTIONS ........................................................................................................7

Making Calls ..............................................................................................................7

Receiving Calls ..........................................................................................................7

Ending Calls...............................................................................................................7

In-Call Functions........................................................................................................7

SX6P BASIC FEATURES ..............................................................................................8

Date and Time Settings .............................................................................................8

Audio Settings............................................................................................................8

Adjust Alert Tones ......................................................................................................9

Speakerphone............................................................................................................9

Phonebook.................................................................................................................9

Speed Dialing ...........................................................................................................11

Change the Display Screen Contrast ......................................................................11

ChangeBacklight Options.........................................................................................11

SX6P ADDITIONAL FEATURES .................................................................................12

Call Logs..................................................................................................................12

Alarm Settings..........................................................................................................12

Language Selection .................................................................................................13

Personalization Options...........................................................................................13

Call Settings.............................................................................................................14

Network Settings......................................................................................................15

SIM PIN Setup .........................................................................................................16

Handset Call Barring................................................................................................17

Restricted Dialing.....................................................................................................18

Deskphone Lock ......................................................................................................18

Closed User Groups (CUG).....................................................................................19

Restore Factory Defaults .........................................................................................19

Phonecell

SX6P GSM v User Manual

SUPPLEMENTARY SERVICES (NETWORK DEPENDENT) .....................................20

In-Call Options .........................................................................................................20

Call Divert (Forwarding)...........................................................................................20

Call Waiting..............................................................................................................21

Multiparty Calling .....................................................................................................21

Caller ID Settings.....................................................................................................21

Blocking Your Number (CLIR) .................................................................................21

Voicemail..................................................................................................................22

Short Message Service (SMS) ................................................................................22

Information Messages .............................................................................................24

Network Call Barring................................................................................................25

DATA FEATURES ........................................................................................................26

Connect SX6P to a Computer .................................................................................26

Configure PC for Circuit Switched Data ..................................................................26

Automatic Baud Rate Fall Back Control ..................................................................26

Digital Fax Setup .....................................................................................................27

GPRS (Packet Data) Connections...........................................................................27

SX6P TROUBLESHOOTING .......................................................................................28

CONFORMANCE STATEMENTS ................................................................................29

SAFETY INFORMATION .............................................................................................29

WARRANTY .................................................................................................................32

APPENDIX A: PC SERIAL PORT SETUP FOR CS FAX AND DATA ........................34

Phonecell

SX6P GSM 1 User Manual

SX6P SETUP

SIM Card Installation

The SX6P requires a Subscriber Identification Module (SIM) for normal operation. The service

provider supplies the SIM card, which carries the account information needed to operate the

SX6P. The SIM compartment is on the back of the SX6P.

NOTE: If you don’t have a SIM card, contact your network service provider.

1. Make sure the unit is off and the power supply disconnected before removing or installing a

SIM Card.

2. Remove the SIM compartment cover by removing the screw.

3. Open the SIM compartment holder.

4. Line up the SIM card with the arrow on the SIM card holder - see Figure 1.

5. Gently insert the SIM card in the slot of the SIM card holder.

6. Close the SIM card holder.

NOTE: Do not force the SIM card holder shut. Make sure the SIM card is aligned properly

with the directional arrow on the holder.

7. Reattach the SIM compartment cover with the screw.

Install Batteries (optional)

1. Remove the battery access door screw located on the bottom of the unit - see Figure 2.

2. Press the battery access door tabs and remove the battery access door.

3. Install the Telular 3.6V rechargeable battery pack into the battery pack area.

4. Reinstall the battery access door using the screw - see Figure 3.

SIM Compartment Cover

SIM Card

Holder

SIM Card

Cover Screw

Figure 2 –

Battery access door.

Battery Access

Door Screw

Battery Access Door Tabs

Battery Access Door

Battery Pack Area

Figure 3 - Battery installation.

Figure 1 - SIM card installation.

WARNING!

Do not use batteries other than the included Telular battery pack with the SX6P.

Using any other batteries may result in fire and/or other damage to the unit.

Phonecell

SX6P GSM 2 User Manual

Battery Operation

The SX6P will recharge its battery pack when connected to AC power. If AC power is interrupted,

the SX6P will continue to operate, using power from the battery. (Standby and talk-times will vary

based upon phone usage during power interruption.)

Location and Setup

The SX6P comes with a standard spike antenna (TNC).

NOTE: The supplied antenna will support either 850/1900 MHz or 900/1800 MHz frequincies,

as specified by your wirless service network provider.

1. Attach and finger-tighten the antenna - see Figure 4. Do not over-tighten the antenna.

2. Select a location that is above ground and as close to windows (or exterior walls) as possible

to get the best signal - see Figure 5.

Connect the Handset

Before you can use the SX6P, you must connect the handset cable.

1. Connect the handset cable to the phone jack - see Figure 6.

2. Connect the handset cable to the handset - see Figure 6.

Phone jack

Handset cable

Figure 4 - Attach the antenna.

Figure 5 - SX6P location.

Handset

Figure 6– SX6P handset connection.

Phonecell

SX6P GSM 3 User Manual

Wall-Mounting

1. Remove the mounting clip from the cradle and re-insert it with the tab pointing up - see

Figures 7 and 8.

2. Mark two hole locations 83 mm (3-1/4 inches) vertically apart and drill two holes into the wall.

3. Install the screws (not supplied) into the wall, leaving a gap of approximately 3 mm

(1/8 inches) between the screw head and the wall.

6. Align the mounting holes with the screws and mount the SX6P onto the screws - see Figures

9 and 10.

Insert

Mounting

Clip into

the Cradle

(tab up)

Mounting Clip in

Cradle (tab up)

Figure 8 –

Handset mounting clip for wall-mount.

Remove

Mounting Clip

from the Cradle

(tab down)

Figure 7 –

Handset mounting clip assembly.

Figure 10 – Mount the SX6P onto the screws.

83 mm (3-1/4 inches)

Figure 9 – SX6P mounting hooks.

Mounting

Holes

Phonecell

SX6P GSM 4 User Manual

Figure 11 –

SX6P AC power connection.

AC Power Cord

Wall Socket

Power Supply

AC Power

Input

Barrel

Connector

Connect the SX6P to AC Power

1. Connect the barrel connector of the power supply to the AC power input on the rear panel of

the SX6P - see Figure 11.

2. Plug the AC power cord into the power supply.

3. Plug the AC power cord into the wall socket.

4. Press and hold the ON/OFF button for 3 to 5 seconds.

5. Check the cellular signal strength and move the unit until the best signal possible is

achieved - see the Service Indication section of this manual.

GETTING TO KNOW YOUR SX6P

Function Keys

Operation of the SX6P is accomplished through the function keys on the keypad of the unit - see

Figure 12.

Figure 12 – SX6P keypad and function keys.

LCD Screen - Displays

icons, information, and

menu options necessary

to operate the SX6P.

LCD Soft Keys - Provide

access to the SX6P menu

options and features.

Hold - Used to put the

active call on hold or to

reactivate an on-hold call.

Mute - Prevents the party on the

other end of a call from hearing any

sound from the SX6P.

Volume - Controls the speaker

volume level for the handset and

the speakerphone when the SX6P

is off-hook.

Redial - Dials the last number

called from the SX6P.

Flash - Allows answering of call

waiting, connecting multiparty calls,

and putting an active call on hold to

make another call. Also can be

used to skip Dial Delay time (quick

dial).

Speakerphone - Engages the

speakerphone feature.

Power - Used to power unit On

and Off.

Phonecell

SX5 GSM 5 User Manual

Phonecell

SX6P GSM 6 User Manual

LCD Screen Icons

Icons displayed on the LCD screen indicate the features in use, the status of the phone, signal

strength and battery status - see Figure 13.

Service Indication

Full Service

When powered on, the SX6P will display a wakeup banner (the 300G models LCD screen and

keypad backlight will also light). After a few seconds, the greeting and mobile carrier will display.

If service is available, the antenna icon will display indicator bars. The number and height of the

indicator bars increases as the signal grows stronger (the more bars, the better the signal).

No Service

When no service is available, the antenna icon will not display any bars. Contact your service

provider to verify cellular service is activated. No calls can be made in this condition.

Limited Service

If there is a signal, but full service with the system is blocked, only emergency calls will be

allowed. Contact your service provider for more information.

Network Registration

If the home network is unavailable, but there is another network available (either another fre-

quency or system), the SX6P will attempt to register to that system. If there is more than one

system, a list of available systems will display.

1. Use the arrow keys to highlight a network from the list.

2. Press the SELECT key. If the selected network cannot be accessed, the list of available net-

works will be updated and a different network must be selected.

Figure 13 – SX6P LCD screen icons.

Received Signal

Strength - Indicates the

strength of the current

signal. The more bars,

the stronger the signal.

Message - Displays when

a new text or voicemail

message has been received.

Speaker - Indicates speaker

phone is activated.

Battery - Indicates the level of

battery power. The more bars,

the more power.

Clock - Displays the

current time.

LCD Soft Key Labels - Provide access to features within

the sub-menus of the SX6P. Labels change according to

the selected sub-menu.

Alarm - Indicates that

the alarm feature has

been set.

Call - Indicates that the hand-

set is off-hook.

CALL FUNCTIONS

Making Calls

1. Pick up the handset or press the SPEAKERPHONE key.

The SX6P is now “off-hook.”

2. Listen for dial tone.

3. Dial the phone number. The dialed number will be displayed. The name will also be displayed

if it is stored in the phonebook.

Correct Dialing Errors

• To erase one digit, press the CLEAR key once.

• To erase all digits, press and hold down the CLEAR key until all digits are erased.

• To insert numbers, use the arrow keys.

Redial the Last Telephone Number Dialed

1. Pick up the handset or press the SPEAKERPHONE key. The SX6P is now “off-hook.”

2. Press the REDIAL key.

Receiving Calls

When there is an incoming call, the SX6P rings, an incoming call notification displays the call

type and Caller ID information (if available).

1. Pick up the handset or press the SPEAKERPHONE key.

2. Begin talking.

NOTE: Press the REJECT key to refuse the call. The phone will stop ringing and the calling

party will be disconnected.

Receive a Call When Caller ID is Activated

The Caller ID feature displays the caller’s number when the SX6P rings. If the caller’s name and

number are stored together in the SX6P phonebook, the caller’s name and number will be dis-

played. Contact your service provider to activate this feature.

NOTE: If there are missed calls (calls not answered), “MISSED CALLS” will be displayed with

the number of calls missed. See

the Call Logs section of this manual for more information.

Ending Calls

Hang up the phone by either placing the handset back onto the SX6P cradle or press the SPEAK-

ERPHONE key if using the speakerphone.

In-Call Functions

Mute a Call

1. While in a call, press the MUTE key. A notification will display in the upper right corner of the

LCD screen.

2. Press the MUTE key again to un-mute the microphone.

Place a Call on Hold

1. While in a call, press the HOLD key.

2. The display will change from Active to Held.

3. To reactivate the call, press the HOLD key again.

Adjust Volume

1. While in a call, press the Volume keys to raise or lower the handset/speakerphone volume.

Phonecell

SX6P GSM 7 User Manual

SX6P BASIC FEATURES

Date and Time Settings

The SX6P allows customization of the date, time, time zone, and time format (12 or 24 hour).

Set the Date

1. Press the MENU key.

2. Select Clock.

3. Scroll to Set Date, then press the CHANGE key.

4. Enter the desired date.

5. Press the OK key.

Change the Date Format

1. Press the MENU key.

2. Select Clock, then select Clock Settings.

3. Scroll to Date Format. The current format will display.

4. Press the CHANGE key.

5. Select the desired date format.(D:M:Y, M:D:Y, or Y:M:D)

6. Press the OK key.

Set the Time

1. Press the MENU key.

2. Select Clock.

3. Select Set Time.

4. Enter the desired time.

5. Press the OK key.

Change the Time Format

1. Press the MENU key.

2. Select Clock, then select Clock Settings.

3. Scroll to Time Format. The current format will display.

4. Press the CHANGE key.

5. Select the desired time format (12 hour or 24 hour).

6. Press the OK key.

Set the Time Zone

1. Press the MENU key.

2. Select Clock, then scroll to Set Time Zone.

3. Press the CHANGE key. Use the two middle soft keys to scroll left or right on the graphic to

highlight the time zone you are in.

4. Press the far left soft key to select the highlighted time zone.

Audio Settings

Adjust Alert Volume (Ringer)

1. Press the MENU key.

2. Select Settings, then select Audio Settings.

3. Select Alert Volume, then set the desired volume level using the arrow keys.

Phonecell

SX6P GSM 8 User Manual

Adjust Alert Tones (Ringer)

Alert tones can be customized for different types of calls, such as voice or text.

1. Press the MENU key.

2. Select Settings, then select Audio Settings.

3. Use the arrow keys to scroll through the alert types.

4. Select the desired alert sound.(Voice call alert, SMS alert, Voicemail alert)

NOTE: If No Alert is selected, no alert will sound.

Turn On/Off the Keypad Tones

1. Press the MENU key.

2. Select Settings, then select Audio Settings.

3. Select Keypad Tones.

4. Select On or Off.

Turn On/Off the Warning Tones

1. Press the MENU key.

2. Select Settings, then select Audio Settings.

3. Select Warning Tones.

4. Select On or Off.

Speakerphone

1. Press the SPEAKERPHONE key. A dial tone will be heard through the speaker and the

Speaker icon will display.

2. Enter a telephone number, press the REDIAL key or press the NAME key to find a number

you have previously entered into the Phonebook - see the Phonebook section of this manual

for details about how to enter a number.

Speakerphone Microphone Adjustment

You can adjust the microphone gain of the speakerphone from -5 to +5 using Spkr Phone Adj in

the Audio Settings menu.

1. Press the MENU key.

2. Select Settings then Audio Settings.

3. Select Spkr Phone Adj then the desired microphone gain using the arrow keys.

Phonebook

The SX6P has an Internal Phonebook capable of storing up to 250 telephone numbers with cor-

responding names in the SIM card (SIM cards may have different memory capacities) and 18 in

the phone memory.

HINT: To dial a number from the Phonebook when off hook, press the NAME key, select the

name, then press the DIAL key.

NOTE: The Phonebook will not be accessible while the SIM Card is read when the SX6P is

powered on. This process takes approximately 60 seconds.

Adjust Phonebook Settings

Entries can be saved to the SIM card or to the phone memory. When numbers are saved to the

SIM card, they can be transferred by removing the SIM card and installing it in another GSM

phone.

1. Press the MENU key.

2. Select Phonebook, then select Settings.

3. Select Save Entries To. (SIM card, Choice or Phone memory).

4. Select the desired location of the phonebook entries.

Phonecell

SX6P GSM 9 User Manual

Keypad Buttons for Text Entry (Multitap)

There are three or four letters (as well as a number) assigned to each key on the telephone

keypad. During text entry, pressing a key displays the first letter, then cycles through the other

letters. For example, if the number 3 is pressed, a “D” will appear. If it is pressed again, the “E”

will appear, and if it is pressed three times, the “F” will appear. The cursor will move on to the

next space after a brief pause, so the letter must be selected quickly.

Enter a Hard Pause

Hard pauses allow the SX6P to be used with automated phone systems used for pagers or auto-

mated banking. When a number is programmed into the phonebook, a pause is entered by

pressing and holding “#” for more than one second. The hard pause will be displayed as “P.”

Use of Lower Case or Numbers

The “

” key can be used to switch change from upper case (ABC) to lower case (abc) or to num-

bers (123). The current setting will display under the clock in the upper right corner of the LCD

screen.

Use Special Characters

The “1” key can access several special characters (punctuation marks and symbols). To scroll

through available special characters, press the “1” key repeatedly.

Add a New Entry to the Phonebook

1. Press the MENU key.

2. Select Phonebook, then select Add Name.

3. Enter a name by pressing the alphanumeric keys (maximum 16 characters).

HINT: Use the “

” key to switch between upper case, lower case and numbers. Use the “0”

key to insert a space between entries. Use the “1” key to access special characters. To cor-

rect errors in the name, press the CLEAR key.

4. Press the OK key.

5. Enter the desired telephone number (maximum of 20 digits).

6. Press the OK key. You will be prompted to enter another number.

7. Press the OK key to save the entry and return to the Phonebook menu. If you have additional

numbers (up to 2 more) follow steps 5 through 7 for each number.

Phonebook Entry Search

1. Press the NAME key.

2. Use the arrow keys to scroll through the entries or use the keypad to view all entries that

begin with a specific letter.

3. Press the SELECT key to view the phone number(s) listed for a highlighted entry.

Edit or Delete an Entry

1. Press the NAME key.

2. Use the arrow keys to scroll through the entries, or use the keypad to view all entries that

begin with a specific letter.

3. Press the SELECT key to view the phone number(s) listed for an entry that is highlighted.

4. Press the OPTIONS key and select the desired option. (Edit Name, Edit Number, Add

Number, Add Name, Add to Speed Dial, Delete Number or Delete Entry).

Phonecell

SX6P GSM 10 User Manual

Speed Dialing

Speed dialing permits one-touch dialing for up to 10 telephone numbers stored in the phone

book. 0 through 9 on the keypad are used for speed dialing. You must press and hold the corre-

sponding key for 2 seconds to use speed dial.

Assign a Number to a Speed Dial Location

1. Press the NAME key.

2. Select the desired entry to add to the speed dial list.

3. Press the OPTIONS key.

4. Select Add to Speed Dial.

5. Use the arrow keys to scroll to a location, then press the SELECT key.

NOTE: If a location is already in use, the phone number that is stored there can be replaced

with a new one.

Dial a Speed Dial Location

1. Pick up the handset or press the SPEAKERPHONE key.

2. Press and hold the number (for 2 seconds) of the location containing the speed dial number

to be called.

3. The number is displayed and dials automatically.

View the Speed Dial List

1. Press the MENU key.

2. Select Phonebook, then select Settings.

3. Select Speed Dial List.

Change the Display Screen Contrast

1. Press the MENU key.

2. Select Settings, then select Phone Settings.

3. Select Screen Contrast.

4. Use the arrow keys to adjust the display contrast.

5. Press the OK key.

Change Backlight Options (SX6P-300G Series Only)

1. Press the MENU key.

2. Select Settings, then select Phone Settings.

3. Select Backlight, then choose the keypad lighting setting you prefer.

ON: Display and keypad are lit whenever phone is in use.

15 Seconds: Display and keypad light when phone is in use, then go dark after 15 seconds.

Power Save: Display and keypad are never lit.

Phonecell

SX6P GSM 11 User Manual

Phonecell

SX6P GSM 12 User Manual

SX6P ADDITIONAL

FEA

TURES

Call Logs

The SX6P stores the telephone numbers of the last ten outgoing calls and the last ten incoming

calls with the dates and times of the calls. These numbers are displayed and can be dialed

directly from the call log.

View the Call Log

1. Press the MENU key.

2. Select Call Log.

3. Select the desired calls to view (All, Missed, Received,Dialed). Calls are denoted by the

following icons:

Dial a Number From the Call Log

1. Press the MENU key.

2. Select Call Log.

3. Highlight the desired call to dial.

4. Pick up the handset or press the SPEAKERPHONE key.

5. A dial tone will sound, then the number will be dialed.

NOTE: This feature will not work for unavailable or private calls (denoted as Withheld in the Log).

Clear the Call Log

1. Press the MENU key.

2. Select Call Log, then select Clear Logs.

3. Select Yes to clear the call log. Select No to return to the Call Log menu.

Check the Last Call Time

1. Press the MENU key.

2. Select Call Log, then select Call Time.

3. Select Last Call Time.

Check Total Accumulated Air Time

1. Press the MENU key.

2. Select Call Log, then select Call Time.

3. Select All Calls Time.

GPRS Call Information

1. Press the MENU key.

2. Select Call Logs then GPRS Info.

Alarm Settings

The SX6P alarm feature can be used as an alarm clock. Alarm time and tone can be set for daily

use or for one time only.

Set Alarm Time and Tone

1. Press the MENU key.

2. Select Clock, then select Set Alarm.

3. Select Set Time, then enter the desired alarm time.

4. Press the OK key.

5. Select Set Tone, then select the desired alarm tone.

6. Press the OK key.

5. Press the OK key.

Set Alarm to Repeat Daily

1. Press the MENU key.

2. Select Clock, then select Set Alarm.

3. Select Repeat Daily.

Turn Alarm On/Off

1. Press the MENU key.

2. Select Clock, then select Set Alarm.

3. Select Alarm Status.

4. Select On or Off.

5. Press the OK key.

Language Selection

The SX6P is capable of displaying menu items in several different languages.

Select a Language

1. Press the (MENU) key.

2. Select Settings.

3. Select Phone Settings.

4. Select Set Language.

5. Scroll through the list of desired languages.

6. Highlight the desired language, then press the SELECT key.

Personalization Options

The SX6P can be customized with a personal greeting that displays when the SX6P is turned

on. It can also be programmed to display your phone number.

Store Your Telephone Number for Viewing

1. Press the MENU key.

2. Select Settings, then select Phone Settings.

3. Select My Number.

4. Press the EDIT key.

5. Enter your phone number.

6. Press the OK key.

NOTE: To display your phone number, follow steps 1-3 above.

Change Greeting Message

1. Press the MENU key.

2. Select Settings, then select Phone Settings.

3. Select Set Greeting.

4. Enter the desired greeting message.

5. Use the arrow keys to change the delay time (2-20 seconds).

6. Press the OK key.

HINT: Use the “

” key to switch between upper case, lower case and numbers. Use the “0” key

to insert space between words/names. Use the “1” key to access special characters.

Phonecell

SX6P GSM 13 User Manual

Call Settings

Minute Minder

When turned on, the Minute Minder emits a low audible tone once every minute while a call is

active.

1. Press the MENU key.

2. Select Settings, then select Call Settings.

3. Select Minute Minder, then select On or Off as desired.

Call Timer

When turned on, the Call Timer displays during an active call. It can be set to remain visible for 30

seconds after the call is terminated or until another action (key press or taking SX6P off-hook).

1. Press the MENU key.

2. Select Settings, then select Call Settings.

3. Select Call Timer, then select the desired option. Options include:

• Off - no call timer displayed.

• On For 30 Sec. - call timer is displayed for 30 seconds or until user action.

• On Until Action - call timer is displayed until a user action.

Dial Delay

The Dial Delay is the amount of time, after a digit is dialed, the SX6P waits before automatically

sending the call.

1. Press the MENU key.

2. Select Settings, then select Dial Settings.

3. Select Dial Delay.

4. Use the arrow keys to change the delay time(2 - 20 seconds).

5. Press the OK key.

Auto Dial

The SX6P is able to recognize frequently called numbers and automatically dial them without wait-

ing for the Dial Delay. Once a number has been called twice successfully, it will Auto Dial when this

option is turned on.

1. Press the MENU key.

2. Select Settings, then select Dial Settings.

3. Select Auto Dial.

4. Select On to enable Auto Dial.

Phonecell

SX6P GSM 14 User Manual

Page is loading ...

Telular Cell Phone 850, 1800, 1900 User manual

Brand: Telular

Model: Cell Phone 850, 1800, 1900

Category: Telephones

Type: User manual

This manual is also suitable for

Download PDF

report

Telular Cell Phone 850, 1800, 1900 User manual

This manual is also suitable for

Telular Cell Phone 850, 1800, 1900 User manual

Related papers

Other documents