009-1744-01
INF5512AG
INF5522AG
INF5532AG
QUICK START GUIDE
1. INSTALLING THE OPS PC AND ATTACHING ANTENNAS
(BIGTOUCH & MONDOPAD ONLY)
1) Remove the OPS PC Bay protective plate on left side of the rear of the panel.
2) Remove PC from box; insert it into the OPS PC bay.
3) Secure the PC with the two thumb screws.
4) Attach the two WiFi antennas to the two antenna ports on the PC.
Note: Install the PC into the OPS PC Bay, before powering ON the display.
2. INSTALLING BATTERIES AND RF MOUSE DONGLE
(BIGTOUCH & MONDOPAD ONLY)
1) Open the battery compartment on the back of the mouse, remove the dongle, and install two fresh AAA batteries.
2) Plug the dongle into the PC USB 2.0 port on the front, left of the display, to connect your mouse.
3) Open the battery compartment on the back of the keyboard, install two fresh AAA batteries.
3. PLUGGING IN/ UNPLUGGING THE DISPLAY
1) Ensure the display is installed in an upright position.
2) Connect one end of the AC power cord to the AC IN jack (trapezoid plug) on the back of the display.
Connect the other end of the power cord to an AC outlet.
Note: Connect the display to a compatible power source only; check the label for your model's specic needs.
Unplug the AC power cord from power outlet, when you are not using the display for an extended period of time.
4. TURNING THE DISPLAY ON/ OFF
1) Toggle the power switch on the back of the panel to the ON/OFF position.
2) Press the power button on the right side front of the panel, to turn power for panel ON or OFF.
Result: The LED on the front of the display turns on to indicate the panel has power.
5. ATTACHING THE CAMERA (MONDOPAD ONLY)
To mount the camera on the top of the panel, follow these steps.
1) Remove center screw, top, back of panel.
2) Attach the camera adapter to top of panel, using the Phillips-head screw, provided with the camera adapter.
3) Place the camera assembly over the camera adapter, then screw in the two thumb screws (provided with the camera),
through the holes, which line up with the attached camera adapter.
6. SETTING UP MS WINDOWS 10 (BIG TOUCH & MONDOPAD)
1) Turn the display power ON and turn the PC system power ON; then wait for Windows to complete its internal processes.
2) Use touch screen commands or your keyboard and mouse to follow the Windows prompts for set-up.
009-1744-01
Result: After you nish Windows setup, the display is ready for use.
For more information: Go to www.infocus.com/support.
5. ATTACHING THE CAMERA (MONDOPAD ONLY)
To mount the camera on the top of the panel, follow these steps.
1) Remove center screw, top, back of panel.
2) Attach the camera adapter to top of panel, using the Phillips-head screw, provided with the camera adapter.
3) Place the camera assembly over the camera adapter, then screw in the two thumb screws (provided with the camera),
through the holes, which line up with the attached camera adapter.
6. SETTING UP MS WINDOWS 10 (BIG TOUCH & MONDOPAD)
1) Turn the display power ON and turn the PC system power ON; then wait for Windows to complete its internal processes.
2) Use touch screen commands or your keyboard and mouse to follow the Windows prompts for set-up.
-
1
-
2
-
3
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Infocus INF5512AG Quick start guide
-
Infocus INF6522AG Quick start guide
-
-
-
-
-
Infocus INF8021k User manual
-
-
-
Infocus INF5522AG Software Guide
Other documents
-
Hitachi HILS65205 User manual
-
ViewSonic IFP6560 User guide
-
AVer CP654i / CP754i / CP864i User manual
-
-
Gateway ONE User manual
-
EUROCOM LCD PC User manual
-
-
Pelco VideoXpert Core – MG and OCC Hardware Installation guide
-
Optoma 5651RK Owner's manual
-
Geovision GV-MNVR2110 System User manual