Digi ConnectPort X4 IA ZB - Ethernet & Cellular Quick start guide

ConnectPort X4 IA ZB - Ethernet & Cellular
Digi
Brand
Digi
Model
ConnectPort X4 IA ZB - Ethernet & Cellular
Type
Quick start guide

This manual is also suitable for

Digi ConnectPort X4 IA ZB - Ethernet & Cellular is a versatile networking device offering seamless connectivity solutions for various applications. With built-in Ethernet and cellular capabilities, it enables reliable data transmission over wired and wireless networks. The device is equipped with XBee radio technology, allowing for the connection of sensors and other devices using the Zigbee protocol.

Digi ConnectPort X4 IA ZB - Ethernet & Cellular is a versatile networking device offering seamless connectivity solutions for various applications. With built-in Ethernet and cellular capabilities, it enables reliable data transmission over wired and wireless networks. The device is equipped with XBee radio technology, allowing for the connection of sensors and other devices using the Zigbee protocol.

Quick Start Guide
ConnectPort® X4 IA Cellular
Welcome to your Digi product
Get started: This guide helps you with initial product setup. Need more? Find additional
product support at www.digi.com/support/ConnectPortX4. Or connect to the online
documentation by scanning this code:
Digi Technical Support: Digi offers multiple support plans to help you get the most out of your
product. For information on Technical Support plans and pricing, contact us at 877.912.3444 or
visit www.digi.com/support.
Documentation Feedback: To provide feedback on this documentation, send your comments
to techcomm@digi.com.
1 Verify your components
ConnectPort X4 DIN rail mounting bracket Ethernet cable
XBee antenna Direct mount antennas
Part number
# of Direct mount
antennas
X4-xxx-P01-x 1
All other models 2
Verify that you have all included equipment. If any item is missing or damaged, contact your supplier.
2 Insert SIM card(s)
Note If your device uses a SIM card, you must insert the SIMcard. If your device does not use a SIMcard, you can skip this step.
1. Remove the SIMslot cover plate.
2. Insert SIMcard(s) as shown. Insert the end of the SIMcard with the chamfered corner first.
n Install the primary SIM card in the upper SIMslot with the contacts face down.
n Install the secondary SIM card in the lower SIMslot with the contacts face up.
3. Reattach the SIM slot cover plate when finished.
© 2018 Digi International Inc.
Digi, Digi International, and the Digi logo are trademarks or registered trademarks in the United States and other countries worldwide. All other trademarks mentioned in this
document are the property of their respective owners.
3 Connect the hardware
1. Using the two provided screws, attach the DIN rail mounting bracket to the ConnectPort X4.
2. Connect accessories as shown.
a. Connect the XBee antenna.
b. Connect the primary direct mount antenna. If you are using two direct mount antennas, connect the secondary antenna on the
opposite side of the device.
c. Connect the Ethernet cable to the device. You can connect the other end to an Ethernet network.
3. Open the power connectors (+ and -).
a. Insert a small screwdriver into the bottom compartment of the connector at a 30-degree angle.
b. Push the screwdriver down to open the connector.
4. Insert the bare wire from a 6-30 VDC power source into the power connectors. Follow the labeling of the positive (+) and negative (-) power
connectors on the device. The positive connector is the leftmost one.
5. Power up the ConnectPort X4.
4 Next steps
After you have connected the hardware, you should configure the ConnectPort X4. Refer to the ConnectPort X4 Getting Started Guide which can
be found at www.digi.com/support/connectportx4.
  • Page 1 1
  • Page 2 2

Digi ConnectPort X4 IA ZB - Ethernet & Cellular Quick start guide

ConnectPort X4 IA ZB - Ethernet & Cellular
Digi
Brand
Digi
Model
ConnectPort X4 IA ZB - Ethernet & Cellular
Type
Quick start guide
This manual is also suitable for

Digi ConnectPort X4 IA ZB - Ethernet & Cellular is a versatile networking device offering seamless connectivity solutions for various applications. With built-in Ethernet and cellular capabilities, it enables reliable data transmission over wired and wireless networks. The device is equipped with XBee radio technology, allowing for the connection of sensors and other devices using the Zigbee protocol.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents