Tuftex 1201A Dimensions Guide

Brand
Tuftex
Model
1201A
Type
Dimensions Guide

This manual is also suitable for

Tuftex 1201A is a versatile and durable roofing panel that can be used for a variety of applications. Made from high-quality materials, Tuftex 1201A is designed to withstand the elements and provide years of reliable protection. With its 26" width, 9/16" corrugation height, and available lengths of 8', 10', 12', 14', and 16', Tuftex 1201A can be customized to fit any project.

Tuftex 1201A is easy to install and can be fastened with either galvanized screws or aluminum nails. It is important to pre-drill all fastening holes to prevent damage to the panel. Tuftex 1201A can be installed on a maximum of 24" on center for vinyl panels and 36" on center for PolyCarb panels.

Tuftex 1201A is a versatile and durable roofing panel that can be used for a variety of applications. Made from high-quality materials, Tuftex 1201A is designed to withstand the elements and provide years of reliable protection. With its 26" width, 9/16" corrugation height, and available lengths of 8', 10', 12', 14', and 16', Tuftex 1201A can be customized to fit any project.

Tuftex 1201A is easy to install and can be fastened with either galvanized screws or aluminum nails. It is important to pre-drill all fastening holes to prevent damage to the panel. Tuftex 1201A can be installed on a maximum of 24" on center for vinyl panels and 36" on center for PolyCarb panels.

1
(See TUFTEX Installaon Guide for more informaon.)
Specificaons
Specs and Installaon Tips
Panel Width: 26” U.S. Standard
Corrugaon Height: 9/16”
Panel Length: 8’, 10’, 12’ Standard and 14’, 16’ available in some colors/
profiles by special order
Galvanized Screws: 2” #10 Galvanized 1/4” Hex-Head Screws with EPDM Washers
(50/box), 12 boxes per case
Aluminum Nails: 1-3/4” x 1/8” Ring Shank Aluminum Nails (3/8” head) with EPDM
Washers (100/box), 24 boxes per case
Fasteners per panel: 8’ = 25 fasteners 10’ = 30 fasteners 12’ = 35 fasteners
Closures: Foam Closures = 3’ length (pack of 5)
Wood Closures = 6’ length (minimum order of 24)
Round profile for SeaCoaster™
Octagonal profile for UltraVinyl™ & PolyCarb™
Light Transmission: SeaCoaster Translucent Blue--75%
SeaCoaster Translucent White--70%
UltraVinyl Crystal Clear--93%
PolyCarb Clear--93%
PolyCarb Translucent White--78%
PolyCarb Smoke--84%
Load Bearing Capacity SeaCoaster = 90 lbs./sq. .
on 24” Centers: UltraVinyl = 90 lbs./sq. .
PolyCarb = 115 lbs./sq. .
ToRemovePanelLabels:Useeithermilddetergentormildcitrus-basedcleaner.
Visit us on the web at www.tuexpanel.com or give us a call.
800-777-7663 (Toll Free) or +540-898-7000 (Internaonal)
TUFTEX
®
2
Storage: Do not stack TUFTEX in direct sunlight or in an enclosure subject to
very high temperatures. Vercal storage indoors is preferred.
Cung: Cut single panels with a pair of snips or heavy duty scissors. Mulple
panels can be cut with a circular saw (plywood blade reversed) or a fine-
tooth hand saw.
Side and End Laps: Seal all side and end laps with a silicone sealer. Overlap sides of panel
one corrugaon and overlap ends a maximum of 4”.
Pitch: Plan a minimum of 1” pitch per foot of run. In heavy snow areas, plan
up to 3” pitch per foot. Greater pitch = less likelihood of leaks.
Cross brace Support Install TUFTEX Vinyl panels on a maximum of 24” on center.
Structure: TUFTEX PolyCarb can span 36” on center.
Heat and Choose the right product for your project. For projects in high heat
Temperature or cold areas where the surface temperature ranges from +270°F to
Issues: -40°F select TUFTEX PolyCarb. Vinyl Opaque panels are suitable for all
weather condions and surface temperatures up to 150°F. Vinyl
Translucent and Clear panels are to be installed for use in milder
weather condions only, and are not recommended for locaons with
high UV or surface temperatures that can exceed 125°F. Never install
TUFTEX panels directly over dark colored raers or closure strips. For
best results, paint (white) the top edge of the raer or closure strip that
is exposed to sunlight. Do not overlap or apply over exisng roofing
or lace.
Venlaon: All TUFTEX covered structures need adequate venlaon to control
condensaon and ensure coolness. In locales where high heat and
humidity frequently occur, choose TUFTEX PolyCarb panels for your
project.
Fastening: Important - Pre-drill all fastening holes. Always pre-drill holes prior to
fastening panels. The diameter of the hole should be 5/16” if using
TUFTEX fasteners. If using other fasteners, the hole must be 2/16 to
3/16” larger than the diameter of the sha of the fastener. Do not over-
ghten fasteners.
(See TUFTEX Installaon Guide for more informaon.)
Installaon Tips
Specs and Installaon Tips
TUFTEX
®
Visit us on the web at www.tuexpanel.com or give us a call.
800-777-7663 (Toll Free) or +540-898-7000 (Internaonal)
  • Page 1 1
  • Page 2 2

Tuftex 1201A Dimensions Guide

Brand
Tuftex
Model
1201A
Type
Dimensions Guide
This manual is also suitable for

Tuftex 1201A is a versatile and durable roofing panel that can be used for a variety of applications. Made from high-quality materials, Tuftex 1201A is designed to withstand the elements and provide years of reliable protection. With its 26" width, 9/16" corrugation height, and available lengths of 8', 10', 12', 14', and 16', Tuftex 1201A can be customized to fit any project.

Tuftex 1201A is easy to install and can be fastened with either galvanized screws or aluminum nails. It is important to pre-drill all fastening holes to prevent damage to the panel. Tuftex 1201A can be installed on a maximum of 24" on center for vinyl panels and 36" on center for PolyCarb panels.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents