Fishbone Offroad 3/4" Leveling Kit Installation guide

Type
Installation guide

Fishbone Offroad 3/4" Leveling Kit is designed to provide a 3/4-inch lift to your Jeep JK Wrangler, improving its off-road capabilities and allowing for the installation of larger tires. The kit includes front and rear coil spring spacers, which are easy to install and do not require any special tools. Once installed, the leveling kit will provide your Jeep with increased ground clearance, making it more capable of tackling rough terrain and obstacles. Additionally, the kit can help to level out the stance of your Jeep, giving it a more aggressive and customized look.

Fishbone Offroad 3/4" Leveling Kit is designed to provide a 3/4-inch lift to your Jeep JK Wrangler, improving its off-road capabilities and allowing for the installation of larger tires. The kit includes front and rear coil spring spacers, which are easy to install and do not require any special tools. Once installed, the leveling kit will provide your Jeep with increased ground clearance, making it more capable of tackling rough terrain and obstacles. Additionally, the kit can help to level out the stance of your Jeep, giving it a more aggressive and customized look.

FB47185
Jeep® JK Wrangler
.75” Lift Kit
4718500
*******THIS INSTALL SHOULD BE DONE BY A PROFESSIONAL*******
*******YOUR VEHICLE WILL REQUIRE AN ALIGNMENT AFTER INSTALL*******
REQUIRED TOOLS
Jack
Jack Stands
Sockets
Rachet
Torque Wrench
Wrenches
Tie Rod, Ball Joint Puller
KIT CONTAINS
Front Coil Spring Spacer
Rear Coil Spring Spacer
QTY
2
2
FB47185
Jeep® JK Wrangler
.75” Lift Kit
1 4718500
BEFORE INSTALLATION:
Check all part and hardware to make sure you have
a complete kit.
Inspect all steering and suspension parts before
installing your kit. Worn or damaged parts could fail
after install of your kit. Replace or repair any worn
or damaged parts.
INSTALLATION:
1) On a smooth, flat, and hard surface. Block
your tires and set the emergency brake.
2) Jack your vehicle up and set on jack stands.
3) Remove your front tires and wheels.
4) Using a jack support the axle on the side of
the Jeep you are working on.
5) Remove the shock, unbolt the sway bar end
link from both sides of the vehicle, remove
the tie rod end nut and remove the tie rod
end from the knuckle. Unbolt brake line
bracket from axle.
6) Slowly release the jack until the axle drops
enough to remove the coil spring. (You
might need to unbolt the track bar from the
axle to get enough drop).
7) Install your Fishbone Coil Spacer over your
factory spring isolator.
8) With the coil spring installed in the spring
pocket slowly raise the axle with your jack.
9) Once the axle is raised enough reattach the
tie rod end, reinstall front shock, and brake
line bracket. (Reinstall track bar into the
axle mount if previously removed).
10) Repeat on the opposite side.
11) Reinstall the sway bar end links once both
sides are complete.
12) Install front tires and wheels.
13) Remove your rear tires and wheels.
14) Using a jack support the axle on both sides
of the Jeep.
15) Remove the shocks, unbolt the sway bar
end link from both sides of the vehicle,
remove the bracket that holds the brake
lines to the body.
16) Slowly release the jack until the axle drops
enough to remove the coil spring.
17) Remove the factory spring isolator and
install your Fishbone spring spacer.
18) With the coil springs installed in the spring
pocket slowly raise the axle with your jack.
19) Once the axle is raised enough reinstall rear
shocks, sway bar end links and brake line
brackets.
20) Install rear tires and wheels.
21) Set vehicle back on the ground.
22) Make sure to tighten all bolts to factory
torque specifications. Re-torque all bolts
after 500 miles.
WARNING!!!
This vehicle now has modified suspension. The
steering, braking and handling will be different than
an unmodified vehicle. Avoid driving conditions that
could cause loss of control. You must drive your
vehicle carefully! If larger tires are installed your
speedometer will read lower than the vehicles
actual speed.
ENJOY YOUR FISHBONE OFFROAD COIL SPRING
SPACERS!!!
  • Page 1 1
  • Page 2 2

Fishbone Offroad 3/4" Leveling Kit Installation guide

Type
Installation guide

Fishbone Offroad 3/4" Leveling Kit is designed to provide a 3/4-inch lift to your Jeep JK Wrangler, improving its off-road capabilities and allowing for the installation of larger tires. The kit includes front and rear coil spring spacers, which are easy to install and do not require any special tools. Once installed, the leveling kit will provide your Jeep with increased ground clearance, making it more capable of tackling rough terrain and obstacles. Additionally, the kit can help to level out the stance of your Jeep, giving it a more aggressive and customized look.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI